I've been attempting to use the GEOMAP command to bring satellite imagery into one of my maps. I have followed theses steps:
1. Signed into my Autodesk360 account.
2. Assigned a coordinate system (SC83F) to my map.
3. Entered the GEO MAP command and selected "A" for aerial image.
Following these steps, I am unable to display the aerial imagery.
AutoCad 2011. I am having no luck when trying to drag a command from the Command List pane to the Quick Access Toolbar. I have success draging to Tool Palettes
View 1 Replies View RelatedI am currently writing a series of routines for setting the layers for text, leaders and dimension commands. The end goal is a system where any annotation command sets the correct layer for the duration of the command, then reverts back to the layer that was active before the command.
I have managed to complete all the code, and it appears to be working fine, I just have one question: I have used -layer "m" "Lay_name" etc... for all layer setting commands, rather than any code to see if the layer exists already. In my limited testing this seems to be suitable, nothing that exists on that layer seems to be affected.
I know how to write code to determine if the layer exists already and set the layer instead, but so far it seems unnecessary??
After installing the VBA Module, I get the message "Unknown command "VBARUN"". I've rebooted, restarted and tried reinstalling the VBA Module to no avail.
View 4 Replies View RelatedI used send command for Export Layout..But the line only executes after exiting command method.
View 9 Replies View RelatedI press CTRL+9 to make the Command Line disappear while drawing. When I plot (or when doing a plot preview) , the Command Line appears again by itself. So I always have to turn the Command Line off manually after each plot
The bug still happens;
- if Dynamic Input is turned off or on
- if I plot to a real device or in PDF
- if the Cammand Line Palette i docked or floating.
This is not an issue in AutoCAD 2012 so I guess it has to do with the new way they programmed the revamped Command Line palette in 2013.
Using Windows7
I need to save a drawing file and give it the name of my desire using a single command, I don't want to issue "saveas" and then specify the name in the file name prompt. This problem is has been faced when I was using ScriptPro and I couldn't succeeded to do that. Hence I need to know if it is feasible to do the stuff using a single command. It will be preferred if I can choose the location to save the file also rather than save the file to the default location.
View 2 Replies View Relatedwithout reiterating a lot of what is said in this thread: [URL] ......
This happen outside the potential malware infection?
if you care to not click-through, the problem is that certain commands (not all of them) simply do not disply in the command line. so the MOVE command for example looks like this:
NORMAL:
Command: _move
Select objects:
NOW:
Command:
Select objects:
same with QSAVE and who knows how many others.
line command is a multiple command. there is a way to execute it like a single command?
View 4 Replies View RelatedHow can i use subtract area command in area command while using add command , often it happens we click on polyline whose area we did not want to consider. How can i do like this, i re click on that enclosed polyline and the area gets subtracted and the green fill goes away?
View 3 Replies View RelatedFew years back our instructor in CAD teaches 'limits' since then i never use limits in all of my drawings. One thing i notice though is when i zoom extents my object seems so big and sometimes i can't use Pan command so what i did is to make a very long line just to make my object small..
* Does setting up limits a must before starting a job?
I am testing the LT 2012 version in Windows. I want to use the pan command which used to be a easily visible button, one click. In 2012 I have to go to View>Pan to acess the button, 2 clicks, If I type P I get a popup menu with every command starting with a P, with Pan at the top, click on Pan, 2 clicks again.
So, can I move the Pan button to the Home tab to make it simpler? Can I edit something so when I type P it knows I mean Pan and don't have to make another choice?
This is really slowing down my process and work flow, it's like stutter! Used to be a seamless flow of click, click, click. Now it is click, pause, search, click, pause, search, click.
I tried applying this flag to one of my commands for Autocad 2006. The documentation states that it forces users to enter the full namespace of the command in order to invoke it.
The problem is that even after defining the local, global, and group names I can't get the command to load. I've tried every possible namespace I could think of when entering the command into Autocad. The command works if I do not apply the flag, and typing GroupName.GlobalName into the command line also works - unless I add the Undefined flag.
[CommandMethod("group1", "cmd1", CommandFlags.Undefined)] _
Public Sub Test()
End Sub
I see people mentioning the filter command what does this do exactly? what are its uses? and how do I use it?
View 9 Replies View RelatedI started on AutoCAD about two weeks ago for my company. The drawings that I have done are in a viewport. There are objects outside of the viewport that I am supposed to copy and past into the viewport to use (transformers, anchors, other utility stuff). The problem with these is that they are in paperspace and I would like to copy them into modelspace. When I try to copy them into model space it says "Duplicate definition of block ****** ignored." able to copy and paste into drawing instead of doing insert command all the time and finding desired block. I am running autocad lt 2004 and do not have a chspace command.
View 9 Replies View RelatedHow to know in which bar a certain command is?
For example, if in need to know the bar in which the command “Align” is, what to do that?
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
Can I create my own custom command?
View 9 Replies View RelatedWhen I used earlier versions of Acad I used to be able to do a calculation within a command. Like if I wanted to offset something equally on each side of a mid-point I could start the offset command then for distance I could put in the distance I wanted/2 (ie if the total distance between the 2 lines needed to be 85.375 i I could do 87.357/2). Is there some setting that I am missing or is this something that has disappeared from Acad?
View 3 Replies View RelatedHow to use the slice command. I'm really not that familiar with 3d. I've done a few but when it comes to roof, I always got stuck into that part. In fact I only heard about the command "Slice" here in Cad tutor. I'm practicing 3d with a house. I'm now on the roof part. And I wanna have this on solid. I made this only by 3dface.
Here is the layout of the roof.
When i go to use the rad or dia. command, and i click on an arc surface (in paper space) the rad dimension will jump to the nearest arc, not the arc that i need dimensioned.
View 3 Replies View Relatedif I load 2 different .NET dll into AutoCAD, and both have a command with the same name, which one will AutoCAD use?
View 2 Replies View Relatedwhat the command for Dim Suffix? I wanted to add "m" in my dimension text but i need the command because i am using it for a script file.
View 3 Replies View RelatedMy AutoCAD now cannot run appload command because the command program suddenly disappear from Support File Search Path AutoCAD.I don't now the file (appload command) are deleted or moved to another folder.
I have to try search its file but didn't find.
I switched LT recently and can not find a command : "laytrans" which is in "normal AutoCad".....
View 9 Replies View Relatedwhat is this purge command, i practice cad 2010. i don't understand the use of purge command.
View 7 Replies View RelatedI have not used Transparent Commands in a LONG time. I'm working in Civil 3D 2012 now. Where are the Transparent Commands?
I would like to dock a toolbar of all the Transparent Commands so they are easily accessible no matter where I have navigated to in the Ribbon.
when I use the insert command by typing I, I used to get a dialogue box in order to locate the file I wanted to insert, but now I do not get the dialogue box, I get the box with the WBLOCK command when I type W. I have ATTDIA set to 1 and changed it several times to no avail.
View 7 Replies View RelatedAutoCAD was working fine on my machine for several months, and now I'm getting this error.
Exception in acmgd.dll ARX Command
Tried repair, resinstall, then uninstalled and installed again, and this keeps coming up.
I am writing a program in vb.net.I have a command.
<CommandMethod("att2att")> _
Public Sub att2att()
Dim ed As Editor
ed = Autodesk.AutoCAD.ApplicationServices.Application.DocumentManager.MdiActiveDocument.Editor
ed.WriteMessage(String.Format("{0} commande: att2att, maintenant disponible...", System.Environment.NewLine))
Dim start As New FileSelect
start.ShowDialog()
End Sub
In the debug mode, the att2att is not recognize.If I compile, netload and call the command, it works. Why is the command not recognize in debug mode?
After deleting some rips and corner seams on my model, I can no longer create rips, unfolds, or refolds. They all come up with the same message as shown in attached picture.
View 3 Replies View RelatedI seem to have lost my command bar on my AutoCAD 2012 drawings. I looked into Options and can not seem to find the command to turn it back on.
View 1 Replies View Related