AutoCAD Inventor :: Mirror A Feature To Opposite Side Of A Part?
Nov 17, 2011I need to mirror a feature to the opp side of a part, then supress the parent feature. Can this be done?
View 5 Replies
ADVERTISEMENT
AutoCAD Inventor :: Mirror And Flip A Feature
Jun 11, 2013I would like to both flip and mirror (or pattern) a feature onto the opposite side of a rectangular extrusion.
For example (assuming a rectangular solid extruded in the Z dimension), I have two counter bored holes on the top surface of the solid aligned with the X axis and I would like a copy of those holes on the bottom surface but aligned with the Y axis. If I pattern the holes rotating them 90 degrees and then attempt to mirror them, I can only select all four or the two originals. Is there any way to disassociate the rotated copies from the originals while still retaining control over their dimensions from a single sketch?
AutoCAD Inventor :: Assembly To Avoid Work Of Forming Opposite Bent Part
Mar 19, 2012I have a formed beam I would like to mirror in an assembly to avoid the work of forming the opposite bent part. I have mirrored it however the cuts in the lower side of the beam are mislocated as if the part were rolled over rather than mirrored.I am in Inventor 2012.
View 9 Replies View RelatedAutoCAD Inventor :: Suppress Base Mirror Feature
Jul 6, 2012Is it possible to create feature A mirror it to create feature B and suppress feature A without suppressing or crashing feature B? What I have are very complicated left hand and right hand features. I could create the B feature again but there are a lot of dimensions. I could mirror the sketch, but there are formulas controlled by iLogic in them, and mirroring a sketch seems to break those formulas and I only get the dimension.
If it is not possible it would be an excellent addition to 2014!
AutoCAD 2013 :: Side Opposite Measurement
Oct 20, 2013I needed to know the Side Opposite so that I could subtract that amount from a known line length.
I knew the angle (24) and the side adjacent (.9375) therefore SIN 24 = X/.9375 .0467= X/.9375 = .3813
When I measure the side opposite I get .4172
See attached screenshot.
AutoCAD Inventor :: Mirror Command Will Not Select Lofted Feature?
Jun 18, 2012I select the mirror command, but it will not select the lofted feature. All of the extruded features will select just fine.
View 5 Replies View RelatedAutoCAD Inventor :: 3D Mirror Does Not Inherit Part Changes
Jul 6, 2012i am using Autodesk Inventor 2012 to design a pipeline structure. I have a problem when mirroring a 3D sketch with applyed frames. the problem is that if after the mirror operation i edit the original sketch, the modifications are not inherited by the mirrored part of the structure. in particular when i mirror a 3D assembly and edit the original assembly the modifications are made also in the mirrored part but the program does it in a wrong way as long as the constraints are not satisfied and the position of the parts are not the same as the original assembly.
How to mirror an object and preserving the link between the original and the copy in order to make modifications to all the parts mirrored in an easy way?
AutoCAD Inventor :: Easy Way To Mirror Part
Sep 21, 2011Is there an easy way to mirror a part? I drew this from a sample and need the opposite handing.
View 1 Replies View RelatedAutoCAD Inventor :: Doesn't Allow To Mirror A Part As Different One
May 15, 2013Inventor doesn't allow me to mirror a part as a different part. In normal cases, I can mirror a part within an assembly and it allows me to give a new filename. Now, it thinks it is a standard part and wants to reuse it even if I uncheck the "reuse standard content and factory parts" box. How can I turn that off? Or mirror the component?
Software: Inventor Series 2011 SP1 x64
OS: Vista Business x64
CPU: E6400
RAM: 2*2Gb GeIL
VGA: Quadro FX 550
GIMP :: Getting The Opposite Side Of Image (2012)
Jun 26, 2012I have an image of a car with a view of looking from the back and to the left, i.e.
[URL].......
I would like to change the view from the back and to the right. Does Gimp have the functionality to do that.
Illustrator :: Reflecting Object To Appear Opposite Side?
Aug 18, 2012I have managed to reflect objects but cannot manage to reflect one object across the Artboard to show up on the opposite side. If you see my image below, I would like to reflect the horizontal stripe at the top of the design and make it appear at the bottom of the Artboard so it finishes the design. Almost all of the work I do requires only one quarter of the design to be created, then I could just reflect it across and then reflect it down so this would be a useful piece of knowledge
View 1 Replies View RelatedAutoCAD Inventor :: How To Link Part Feature In One Part To Another
Jun 21, 2012Very new to inventor 2012 coming form solid edge way back in the day (1998 to 2008) to autocad 2d. getting ready to move to the inventor and trying to figure out some things. searched videos , training etc but not even sure what to call it.
My questions are:
1. I design stamping dies and I will want to build sections from a stock strip with the outside then adding hole, dowels etc. what is the best work flow for this? It is kinda the middle between top down and bottom up.
2. what is the best work flow for adding counter bore , dowel in the block and then having this tied to the mating block so if I move the location of the holes in the block then move as well?
Maya Animation :: Mirroring Rig Controllers To Opposite Side
Sep 10, 2011Is there a tool to mirror objects like there is in Max inside Maya? I am trying to copy my rig controllers to the opposite side but I cant find any tools to do it in 1 click...
View 1 Replies View RelatedAutoCAD Inventor :: Part Are Not Constrain In Assembly If Use Mirror Option
Dec 6, 2012I am working in assembly .there is lot of similar parts in both side. i want to mirror that part. it was mirror but not constrain.
View 1 Replies View RelatedPhotoshop :: Dropdown Menus Open On Opposite Side Of Arrows
Jul 29, 2013After a reinstall of 5.5 I noticed the secondary drop down menus open on the opposite side of the arrows.
View 5 Replies View RelatedIllustrator :: Variable Width Tool - Changes Opposite Side Of Image
Nov 14, 2012Ive been messing around with the variable width tool, Im not sure I i changed something, I did try to restore defaults but when I make a change it changes the opposite side of the image. For example In screen shot I changed the width on the left and the effect showed up on the right.
I would like the width to change where I change it.
AutoCAD Inventor :: Make Feature In Part Be Transparent?
Jan 20, 2012How can I make a feature transparent in a single part? Like one extrusion in a part?
View 9 Replies View RelatedAutoCAD Inventor :: Can Delete Part Of A Fillet Feature
Dec 7, 2011Can you delete part of a fillet feature? While still keeping part of it & adding to it.
I have a fillet feature with 2 fillets to a part. One is in the wrong place.The Feature Fillett1 if you edit it, you will see what I mean.
Keep the middle one. Both fillets are 0.25" / Replace the bottom fillet to the top corner.
I would like to keep the Feature in the order it is in, if possible.
I am using Inventor 2012.
AutoCAD Inventor :: Create A Part That Has Spherical Feature?
Apr 16, 2013I am trying to create a part that has a spherical feature. The spherical feature is "sliced" on the front and back to create a flat surface (see Compound Rest Handle Isometric image). Should I use workplanes to slice the sphere? What is an efficient process the slice the sphere. See Compound Rest Handle Front and Compound Rest Handle Back images and compare to the final result in the Compound Rest Handle Isometric image).
View 9 Replies View RelatedAutoCAD Inventor :: Add Thread Feature To A Part Using ILogic
Dec 27, 2012Possible to add a thread feature to a part using iLogic.
Basically in the iLogic form if the user selects "Threaded Rod" the existing Extrusion is updated to reflect a cylinder with a length and diameter specified by the user and then I need to have a Thread Added to the cylinder.
Computer Specs:
Windows 7 (64 Bit) Pro. SP1, Inventor 2014 Pro, 3D Connexion SpaceNavigator (Driver 3.15.2)
Motherboard: ASUS Rampage IV Extreme x79 Socket 2011
Processor: Intel Core i7 Six Core Sandy Bridge-E 3.2GHz OCed to 4.7GHz (Under Water)
RAM: G.Skill Ripjaw Z-Series 32 gig quad channel of RAM 1800MHz OCed to 2133MHz
Video Card: 2x Nvidia Geforce GTX 770 (Running Six (6) Monitors)
Monitors: [Primary = 2x 24in HD WS][Secondary = 2x 22in HD WS][Tertiary = 2x 19in FS]
Primary Hard Drive: OCZ Vertex IV 256 GB Solid State Drive
Secondary Hard Drive: OCZ Vertex III 120 GB Solid State Drive
AutoCAD Inventor :: Transferring An Assembly Feature To The Related Part?
Apr 19, 2012Is there a way in Inventor to take an assembly feature and basically have it fall out at the part level also? So if you were to open the part up, it would have the cutouts in it.
View 2 Replies View RelatedAutoCAD Inventor :: Link Hole Feature In A Part In Assembly?
Feb 22, 2012I am trying to link a hole feature in a part in an assembly with the number of a particular feature in another part within the assembly. I have a base plate part with a coutersunk hole feature that I want to pattern by linking it to the number of bosses in another part within the same assembly.
View 6 Replies View RelatedMaya Animation :: How To Mirror A Locator (Null) To Other Side
Jan 5, 2011i did a Locator (Null) and parented to the Head Bone.this is where i am going to parent the sphere geometry of the eye.
but i cant find the way to mirror this Locator to the other side for the other eye.i try with Duplicate special, -x but it does it on its own, the only different is the scale is -X but didn't move from the original position, and the 2 are overlap.
how do i mirror / duplicate the Locator to the other side?
After Effects :: Resize One Side Of Solid Without Mirror Effect?
Oct 28, 2013i want resize solid, but just one side, like in photoshop. It is possible? When i try, its resize my solid in whole dimension.
View 4 Replies View RelatedAutoCAD Inventor :: How To Show A Feature Of A Part File As Dashed In A Drawing
Jul 18, 2013How to show, if it's possible, a feature of a part file as dashed in a drawing?
View 2 Replies View RelatedAutoCAD Inventor :: Assembly Hole Feature To Be Transferred In Subsequent Part?
May 28, 2013at assembly level hole feature shown only in assembly. how to create same feature at same position on parts.
View 5 Replies View RelatedAutoCAD Inventor :: Place Feature In Part File Has No Structural Parts
Oct 10, 2012When I insert a standard 6" square tube into an assembly there are all of the custom shapes and standard structural members to choose from. When I try to put the same tubing into a part file only the custom shapes are visible and no standard parts to choose from.
I can only guess that I have some obscure check box missing. There appears to be no good reason why I would be restricted in part files.
AutoCAD Inventor :: Create Non-associative Solid Base Feature In Second Part
Sep 19, 2013“Associative body copy API Sample” 2013 API help.
The above code in the API help shows how to do an associative or a non-associative copy in an assembly of one part into another part. ..BUT the non-associative copy does not always work correctly....
I have been testing this sample code and notice the following limitations with the lower part entitled “Create a non-associative solid base feature in the second part”...
The code uses the proxy body for the source object but it does not use the proxybody for the target object and therefore the relative positioning is wrong for the nonparametricbasefeature when it is created in the target object if the real target body is in a different place than the targetbodyproxy (e.g. it has been rotated/moved in assembly space).
I notice that if you perform this manually using the “copy object” button the relative positioning is maintained correctly even if both target and source objects have been rotated/moved in the assembly...
AutoCAD Inventor :: Can't Get COG Of Single Part Inside Assembly Using Default Feature Of ILogic
Jul 10, 2012can't get the COG of a single part inside an assembly using the default feature of iLogic:
centerPt=iProperties.CenterOfGravityOfComponent("part1:1")
Wikihelp states that it's possible to get the COG of a part within an assembly.It doesn't seem to work anytime getting an error on some missing included references .do I need a Sub-Rule inside the single part?
AutoCAD Inventor :: ILogic To Change Feature Occurrence Upon Opening Part By User
Jul 9, 2013I downloaded a model off a website, it is, (excuse my electrical background ignorance) a jumper for terminal blocks.Our electricians use these and cut them down to size as needed.
Is there a way to use iLogic and a form or message box, to prompt upon opening the part as to how many jumpers are needed for the current assembly> It comes stock with 10, but they sometimes only use 2, 3 4 etc. etc..
I didn't model the part, but I can if it will make the rule easier to write.My idea I suppose was to have the part modeled with 2 jumpers and then use ilogic to create more if necessary.
AutoCAD Inventor :: Bend Part Doesn't Work With Thread Feature Present
Oct 31, 2012I've attached an example of a workflow we use to make different instances of products.part1 gets assembled in assembly1 which then gets derived in part2 to receive a bend.We use assembly1 in one place and part2 in another.(this is a simplified example, made with IV2013 SP1.1)
In part1, if you add the thread feature, the "bend part" feature in part2 fails after updating.This also happens if you try to add a "bend part" to part1 AFTER the thread feature, if the bend is present beforehand it does work.
Having the bend before the thread feature in part1 doesn't work with our workflow, because we need the assembly1 to be straight.In short, the thread feature is causing problems with "bend part".
I can't say if this problem was present in previous versions or even in the previous service pack since we don't use this workflow that often, especially with threaded parts, but i hope this can get fixed with a hotfix.
Using IV2014 Pro SP1 update 1, Win7-64bit