AutoCAD Inventor :: ILogic Reference Parameters
Oct 9, 2013
I'm having some difficulties with iLogic and reference parameters.
I have made a tube with a weird shape and I want to measure the longest length. So I have to cut the tube in a certain angle in relation with the center to measure the length.
The problem is that this angle is really hard to calculate.
So I tried making a rule where I can make my angle shift x degree and then measure the longest length. If the measurement is larger the previous measurement the angle will shift x degree again until the measurement is smaller than the previous.
So I made my starting angle 0 degree, I know this is for a fact not the longest length. And then I tried this rule. (before making a While rule).
And I noticed that on screen the measurement changes. But the reference - parameter stays the same. So it gives me the measurement on the starting angle & after rotating it again gives me the starting angle.
How can I get the parameter to update itself in between?
Dim measurement_length As DoubleDim measurement_length2 As DoubleMessageBox.Show("Start angle ", "My iLogic Dialog", MessageBoxButtons.OK, MessageBoxIcon.Asterisk, MessageBoxDefaultButton.Button1)angle_measurement_spec = 0RuleParametersOutput()InventorVb.DocumentUpdate()measurement_length = [code].....
View 1 Replies
ADVERTISEMENT
Sep 26, 2013
I named a driven dimension parameter so I can reference it elsewhere in my model. The problem is that the driven dimension is in inches and the reference parameter does not allow me to change the units. I would like to use that driven dimension in my model and divide it by the pitch in a pattern to get the correct count for my pattern. The pattern dialog box is expecting a unitless input.
I tried creating a unitless user parameter that referenced the reference parameter but that did not work.
View 2 Replies
View Related
Jan 11, 2012
When a table driven i-feature is placed in a part the parameters are reference. I believe that is how it has always been.Although, to my recollection in versions previous to 2010 when an i-feature was deleted the sketch was maintained and the parameters then became model parameters.
To test this I created a table driven i-feature from scratch to make sure it was not a migration issue.
I have include a screen shot of the deleted i-feature and the result of the parameters is shown. Verify that prior to 2010 the parameters became model parameters or did they stay reference?
View 6 Replies
View Related
Nov 22, 2012
I want to reference parameters in an iRule in such a way that the value of parameter A determines the value of parameter b.
In this case i want to reference the dimensional height of a UC beam into a parameter <UC_HEIGHT> and then allow this to determine the value of uc designation size in a parameter <UC_DESIGNATION>
This would be useful because instead of typing the uc designation of a beam into the part description or matl. list i can just reference a parameter.
Is this possible? Iv tried an iRule along the lines of
if parameter (uc height) = xxx.x then parameter (uc designation) = 'custom test'
but get error messages
View 3 Replies
View Related
Mar 27, 2013
I have an ipart which is being controlled by an external spreadsheet. Each cell references a cell within a spreadsheet on my local drive. I have a set a parameters that are used to completely define each part but I am also interested in some of the reference parameters (from driven dimensions) so that I can analyze relationships between reference and input parameters. Is it possible (without extensive programming in windows VB or other) to export data from this iPart into, prefereably, the driving spreadsheet or another spreadsheet?
View 3 Replies
View Related
Jun 24, 2013
I have some manufacturing dimensions that are an end result of my design so they are driven dimensions at the end of my modeling history and pulled into the ipart table. If I make some design changes I need these dimensions to update too. The problem is they do not automatically update and require a manual activation of each child memeber for the dimension to update.
The dreaded "The Values in the active row don't match the document's current values. do you wish to update the table before continuing" Click, enter, Click, enter, Click, enter.
Autodesk Inventor 2012 Certified Assosicate
Autodesk Inventor 2012 Certified Professional
View 1 Replies
View Related
Feb 20, 2013
I would like to save parameters marked as Key to an XML-file (from an Inventor addin, VB.NET):
Dim addIn As ApplicationAddIn = m_inventorApp.ApplicationAddIns.ItemById("{3bdd8d79-2179-4b11-8a5a-257b1c0263ac}") 'iLogic addin addIn.Activate() Dim iLogicAddin As Object = addIn.Automation iLogicAddin.ParametersXmlSave(invDoc, "c: emp ext.xml", iLogicAddin.XmlSaveOption.KeysOnly)
This doesn't run: "Public member 'XmlSaveOption' on type 'iLogicAutomation' not found."
The documentation says:
Autodesk.iLogic.Interfaces.IiLogicAutomation.ParametersXmlSave(Inventor.Document,System.String,Autodesk.iLogic.Interfaces.XmlSaveOption)
What is the correct syntax to get the XmlSaveOption?
View 1 Replies
View Related
Mar 8, 2012
In the attached file there is a User Parameter, "Antal_ledekasser". Inventor has calculated its value to 2.
If you do the math by hand then you see the value should be 5.
Rebuild doesn't force recalculation.
There is an iLogic rule in the part, but this also fails to force recalculation:
iLogicVb.UpdateWhenDone=True
InventorVb.DocumentUpdate()
ThisDoc.Document.Rebuild2
ThisDoc.Document.Update2
Manual work around is to change the formula, then the value is recalculated.
iLogic work around is to change a parameter-value - and run the rule TWICE.
Question: How do I force a real rebuild, that actually wil recalculate parameter-values the first time I run the iLogic rule?
Background: The attached file is a little subset of the skeleton in a large assembly that is controlled by iLogic. The rules are placed in the topassembly, and writes vaules to the skeleton-file.
After writing values to skeleton-parameters I try to force them through with this iLogic
RuleParametersOutput()
InventorVb.DocumentUpdate()
iLogicVb.RunRule("Skeleton", "Update")
Later in the process I use calculated values to decide which components should be active. But my logic fails because my decisions are made on faulty values.
I did manage to get the updating work in 2011. But after migrating to 2012, it seems impossible to have it update correct. The user has to run rules several times, and doing manually updates to get a correct model.
View 2 Replies
View Related
May 21, 2013
I want to export reference parameters to an excel table using i-Logic
I found the function GoExcel.CellValues("filename.xls", "Sheet1", "A2", "A10") = MultiValue.List("d0")
It looks like the syntax calls for the file location and name if the xls file is not open and if open is not supposed to be required.
I have entered it both ways and with and with out the target file open and with the function GoExcel.Open("pathFilename.xls","sheet1") and continue to get the error:
we couldn't find C:AbellAbell VaultWorkSpaceDEVELOPMENTAC100-0100MRLTEST Table.xls. Is it possible it was moved, renamed or deleted?
Also, I was expecting that to fill in the sheet cell's would be MultiValue.List("d0","d1","d2")
but the system give me an error that says
Error on Line 3 : Overload resolution failed because no accessible 'List' accepts this number of arguments.
See below
GoExcel.Open("C:AbellAbell VaultWorkSpaceDEVELOPMENTAC100-0100MRLTEST Table.xls", "AC-100-0101003-TEST")GoExcel.CellValues("C:AbellAbell VaultWorkSpaceDEVELOPMENTAC100-0100MRLTEST Table.xls", "AC-100-0101003-TEST", "A2", "A10") = MultiValue.List("d194_A")GoExcel.Save
View 8 Replies
View Related
Jun 7, 2011
I am trying to enter some material ordering info into an external spreadsheet, and have that info reflected in a text box within an idw drawing file.
My method is as follows:
Obtain a numerical value (250) from an external Excel spreadsheet (sample.xlsx).Assign this value to a parameter (abc) in an idw file (Materials Ordering.idw).Insert parameter abc I made into a text box within the same idw file.
I made a set_parameters rule, and the ilogic text of the above example is as follows:
'Open File and Scan line - Part = Impeller Casing Flange
i = GoExcel.FindRow("sample.xlsx", "Sheet1", "Part", "<=", "Impeller Casing Flange")
'abc = Material Width
abc = GoExcel.CurrentRowValue("Material Width")
I had no problems with the first two steps, after checking the parameters I could see that parameter abc is being updated successfully.
However, I am having trouble with the third step. In the format text dialog box, I can see a drop box for components, but I can't find a reference to the idw file in there.
My question is, am I going the wrong way about this? Should I have assigned the parameters to a component instead of the idw file?
View 5 Replies
View Related
Aug 22, 2012
Working code ...... attaching file
Auto = iLogicVb.Automation
Dim iLogicAuto As Object
iLogicAuto = Auto
Dim oDoc As Document
oDoc = ThisApplication.ActiveDocument
[Code]...
'but now something more i wanna do is...... delete parameters
If Not (param Is Nothing) Then
For Each param In params
i = MessageBox.Show("Checking for Parameter in File")
i = MessageBox.Show("No.of Parameters exists are ="& param.count)
[Code]....
View 5 Replies
View Related
Mar 8, 2013
I was wondering if there was a command that will get the file name of the model referenced in a drawing?
The reason I want to do this is because I have various programs to automate drawings, but I have to manually edit the code if i want to switch between using the code on assembly drawings and part drawings.
If i can get the model reference, I can then use a bit of extra programming to extract the extension. (i.e. .ipt or .iam)
Autodesk Inventor Professional 2011
Windows 7 Enterprise, 64-bit
View 5 Replies
View Related
Jul 17, 2013
iLogic code question concerning how Place iLogic Component and retain the ability to push parameters from the subassemblies to the parts after being renamed.
I have ASSEMBLY.iam containing:
SUBASSEMBLY-01:1.iam
SUBASSEMBLY-02:1.iam
and sometimes SUBASSEMBLY-02:2.iam
each SUBASSEMBLY.iam contains PART1.ipt and PART2.ipt which have variable LENGTH and WIDTH. LENGTH and WIDTH are entered manually at the SUBASSEMBLY.iam and are infinitely variable.
To transfer the parameters I'm using iLogic code in the SUBASSEMBLY:
Parameter("PART1.ipt", "LENGTH")=LENGTHParameter("PART1.ipt", "WIDTH")=WIDTHParameter("PART2.ipt", "LENGTH")=LENGTHParameter("PART2.ipt", "WIDTH")=WIDTH
Issue 1: When I place the SUBASSEMBLY as an iLogic Component, the parts are renamed to PART1-01.ipt which renders my Parameter transfer useless. What am I missing on writing this code so it can find the new part name?
Issue 2: I like the automatic renaming that happens with Place iLogic Component. Is there a better way to handle this automatically through Place Component -> Save & Replace?
Inventor 2013
View 1 Replies
View Related
Sep 11, 2013
I am looking for information on the option parameters, any documentation?
I found some code to query what parameters there are (Rule: GetTranslatorOptions), just not sure what the enumerations are for some.
Specifically: ExportUnits, Resolution
Using Rule:ExportSTL
I have changed the Export Units from 1 to 4 and do not see any change to the STL ASCII output.. not sure what this parameter does... Expected it to be an enumeration of the drop-down box that you see during "manual" exporting.
View 1 Replies
View Related
Aug 14, 2013
I have this little iLogic snippet that writes out the name and value of all parameters in active document.
doc = ThisDoc.Documentparams = doc.ComponentDefinition.Parametersnames = New List(Of String)values = New List(Of String)For Each param In paramsIf Len(param.Name)>4 Thennames.Add(param.Name)values.Add(param.Value.ToString)ElseEnd IfNextMultiValue.List("ParamsList") = namesMultiValue.List("ParamsValues") = valuesGoExcel.CellValues("COVER.DEFAULT.PARAMS.xlsx", "Sheet1", "A2", "A400") = MultiValue.List("ParamsList")GoExcel.CellValues("COVER.DEFAULT.PARAMS.xlsx", "Sheet1", "B2", "B400") = MultiValue.List("ParamsValues")GoExcel.SaveGoExcel.Close
The problem is it ignores the parameter's units and assumes cm for length and rad for angular. I need another nested IF - Then that says:
IF param.Values.'UnitType' is "in" THEN
param.Value = param.Value/2.54
Else If param.Values.'UnitType' is "deg" THEN
param.Value = param.Value*360/2/3.14159
End If
I just do not know the syntax or proper method.
View 1 Replies
View Related
Dec 26, 2013
Is there a way to work with parameters on a suppressed assembly using iLogic.Everything works fine, but when I suppressed a part ilogic rule give me an error: Parameter: The component named "xxxxx:1" was not found.
View 1 Replies
View Related
Apr 3, 2012
I want to import the parameters from the .ipt file into the .iam file using a rule from iLogic (unless there is another way to do it?)
I pinched the code from the example hand rail iLogic part that comes with inventor and tweaked it to suit. After inputting the code shown in the image, when I click OK I get a 'fatal error' of some sort.
View 6 Replies
View Related
Jun 12, 2013
Is there a standard command or command sequence that allows for the changing of a parameter, say length, of a component from within an assembly. I'm looking to compile a code that allows for a template to be created, then that template will do changes based on text box input and then save out the modified parts with new part numbers.
View 2 Replies
View Related
Aug 30, 2013
I need import all new params, rules and forms from a new template to older parts. I'm trying to use an external rule to create a new iproperties and import params from xml file but I can't assign these parameters with these iproperties.
I attach the code.
View 3 Replies
View Related
Apr 12, 2013
I wish I perform the following code with iLogic. Is it possible to change a model parameter to a reference parameter?
If My_Expression Then' My dimension "d0" is a Driven Dimension' or' My dimension "d0" is a Reference ParameterElse' My dimension "d0" is NOT a Driven Dimension' or' My dimension "d0" is a Model ParameterEnd If
View 9 Replies
View Related
Oct 4, 2011
how to replace model reference using iLogic in inventor 2012. Basically I have a drawing file whose model reference needs to change with part number(iProperties) .
I've been struggling to perform replace model reference as there is no direct command given for it.
View 1 Replies
View Related
Aug 6, 2013
Is there a way in iLogic to iterate through all curves on a drawing. We manually apply radii labels to each drawing view but would like to automate the process with iLogic. How could I reference and cycle through all the radii on my drawing view?
View 2 Replies
View Related
Oct 26, 2011
Is there a way to set an assemblies bill of material setting to reference through iLogic?
View 3 Replies
View Related
Sep 17, 2012
I have a pattern of reference components, but the quantity of the pattern can change based on certain criteria. When the quantity increases or decreases, I need each pattern element to have its BOM structure set to reference.
The problem is, even if the original pattern element is set to reference, each subsequent element comes in as normal. This causes the BOM quantities for that component to be reported incorrectly in higher assemblies.
Is there some iLogic or VBA code that will automatically set each component in a pattern to BOM structure "Reference", even if the pattern quantity changes?
View 7 Replies
View Related
Aug 23, 2011
I would like to be able to use iLogic to get the value of the Comment field of a model's parameters. I have some text there that I would like to display in a sketched symbol. The attached image illustrates what I am seeking.
View 2 Replies
View Related
May 7, 2012
So far I can discover parameters and ilogic aren't possible in the definition of a drawing border.
How can fold lines be created in a border that can be used for multiple scales?
View 1 Replies
View Related
Oct 3, 2013
I made a flanged connection using I logic. Very simple Tube + Flange + Gasket + Blind flange + Bolting.Then I tried to write some ilogic rule to have Blind flange on / off when needed, hence the Gasket & Bolting also need to be off. Like in these images:
That works fine visually, but I also want the BOM to be set accordingly. For the Blind flange & Gasket my BOM is OK. But for my bolting the BOM is not OK. I tried to set the BOM structure the same way as the visibility but that failed. It only subtracted 1 bolt from my list (see code)
If Blindflange_status = 0 Then 'Bolting offComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kReferenceBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = FalseElse 'Bolting onComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kDefaultBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = TrueEnd If
Is there a way to set all parts within a pattern BOM structure? I made my bolting by adding 1 bolt, 1 washer & 1 nut and then pattern them using feature pattern select.
Inventor 2013
View 1 Replies
View Related
Dec 11, 2012
How to reference the drawign sheet number using iLogic? I see on the snippets on the side a way to reference the sheet name, but I only want the number. To get the name it is ActiveSheet.Name, but ActiveSheet.Number does not work. Getting the name give something like ASSM:1, so if there was a way to take that and subtract the colon and everything before it that would work also. I am not a programmer, I've just taked some programs I found online and modified them a little to do what I want to do, but this is holding me back a bit.
Overall, I'm trying to modify the drawing view label to have a project number, referenced from the drawign iProperties, a view label, and sheet number, and then save that info in an iproperty of the part, and then reference that in the BOM so it automatically labels all of the views and fills out a column of the BOM to reference which page and view to find the parts of the assembly. I have everything working except for the sheet number.
View 5 Replies
View Related
Oct 3, 2013
I made a flanged connection using I logic. Very simple Tube + Flange + Gasket + Blind flange + Bolting.
Then I tried to write some ilogic rule to have Blind flange on / off when needed, hence the Gasket & Bolting also need to be off. Like in these images:
That works fine visually, but I also want the BOM to be set accordingly. For the Blind flange & Gasket my BOM is OK. But for my bolting the BOM is not OK.
I tried to set the BOM structure the same way as the visibility but that failed. It only subtracted 1 bolt from my list (see code)
If Blindflange_status = 0 Then 'Bolting offComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kReferenceBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = FalseElse 'Bolting onComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kDefaultBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = TrueEnd If
Is there a way to set all parts within a pattern BOM structure?
I made my bolting by adding 1 bolt, 1 washer & 1 nut and then pattern them using feature pattern select. Inventor 2013
View 9 Replies
View Related
Oct 28, 2013
I have two user parameters saved in a part template that are tied to the part volume and an overall estimated part weight. The user parameter Pc_Volume is the volume in cubic feet and calculated by pulling the part mass (in cubic inches) and converting to cubic feet via ilogic rule. This is then automatically run via event triggers before a file is saved and if the part geometry has changed to keep the volume up to date. These are exported because they get pulled into iproperties of our drawing files as well as used to create a parts lists showing the volumes and weights.
I have the property formats of the user parameters set to Number and to unitless and the unit display turned off so it does not show on the parts list, with a precision of 0.000 for Pc_Volume. The Pc_Weight is set the same way however with a precision rounded to the nearest whole number.
These are created this way so when we use the part file as the template when we select "Make Components" to separate our parts and tie them to an assembly all the files are then updated and the information saved for exporting.
The problem is, the Pc_Volume always comes in rounded to a whole number. The Pc_Weight Does as well, but that doesn't bother me since we want it to do that anyway. If I would go into the part file after it's created, double check the precision and then re-run the rule the volume will show up with the correct precision in the exported parameters. I don't want to have to open each partfile however to get this to update.
Attached are images of the parameters, ilogic rule, and exported results.
View 2 Replies
View Related
Apr 2, 2013
I already have a code below that will read a bunch of drawing filenames that will go into each drawing, save the drawing, (print the drawing but I have this disabled for now,) close it, then move onto the next one.
What I want to do is add reference brackets around every dimension on each drawing. I have managed to update part list styles before using ilogic but I am not sure if it is possible with dimensions.
question = MessageBox.Show("Are you sure you want to update multiple drawings? If so, make sure all drawings are checked out.", "Batch Drawing Update",MessageBoxButtons.YesNo,MessageBoxIcon.Question)
'set condition based on answer
If question = vbNo
Exit Sub
End If
[Code] ......
View 4 Replies
View Related
