AutoCAD Inventor :: ILogic To Set Pattern Components To Reference
Sep 17, 2012
I have a pattern of reference components, but the quantity of the pattern can change based on certain criteria. When the quantity increases or decreases, I need each pattern element to have its BOM structure set to reference.
The problem is, even if the original pattern element is set to reference, each subsequent element comes in as normal. This causes the BOM quantities for that component to be reported incorrectly in higher assemblies.
Is there some iLogic or VBA code that will automatically set each component in a pattern to BOM structure "Reference", even if the pattern quantity changes?
View 7 Replies
ADVERTISEMENT
Oct 3, 2013
I made a flanged connection using I logic. Very simple Tube + Flange + Gasket + Blind flange + Bolting.Then I tried to write some ilogic rule to have Blind flange on / off when needed, hence the Gasket & Bolting also need to be off. Like in these images:
That works fine visually, but I also want the BOM to be set accordingly. For the Blind flange & Gasket my BOM is OK. But for my bolting the BOM is not OK. I tried to set the BOM structure the same way as the visibility but that failed. It only subtracted 1 bolt from my list (see code)
If Blindflange_status = 0 Then 'Bolting offComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kReferenceBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = FalseElse 'Bolting onComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kDefaultBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = TrueEnd If
Is there a way to set all parts within a pattern BOM structure? I made my bolting by adding 1 bolt, 1 washer & 1 nut and then pattern them using feature pattern select.
Inventor 2013
View 1 Replies
View Related
Oct 3, 2013
I made a flanged connection using I logic. Very simple Tube + Flange + Gasket + Blind flange + Bolting.
Then I tried to write some ilogic rule to have Blind flange on / off when needed, hence the Gasket & Bolting also need to be off. Like in these images:
That works fine visually, but I also want the BOM to be set accordingly. For the Blind flange & Gasket my BOM is OK. But for my bolting the BOM is not OK.
I tried to set the BOM structure the same way as the visibility but that failed. It only subtracted 1 bolt from my list (see code)
If Blindflange_status = 0 Then 'Bolting offComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kReferenceBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = FalseElse 'Bolting onComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kDefaultBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = TrueEnd If
Is there a way to set all parts within a pattern BOM structure?
I made my bolting by adding 1 bolt, 1 washer & 1 nut and then pattern them using feature pattern select. Inventor 2013
View 9 Replies
View Related
Jan 29, 2013
I'm new to inventor and I need to be able to create coppies of a part in my assembly that are uniquely identified so they can be individually changed. I see that this can be done through the ribbon with the "Place iLogic Component" button, but is it possible to do this from the API in a rule?
I am using inventor 2012 pro.
View 2 Replies
View Related
Sep 25, 2012
I want to arrange these outer circles in a corcular pattern at equal distance and at equal angle from each other without using circular patten feature in assembly tab. How do I do that.
The reasomn I dont want to use circular pattern in assembly tab is if I do that then, I cannot change color of each outer circle separatly If I change one color it changes color for all of these whcih i dont want.
I want to have each outer circle of different color.
View 3 Replies
View Related
Apr 9, 2013
In Inventor 2012 I know that it is possible to arrange assembly components in a circular or rectangular pattern. But is there a way to arrange these components in an oval pattern?
View 5 Replies
View Related
Jul 10, 2012
Lets say you have 100 Keps Nuts in an assembly. Named (KepsNut1,KepsNut2, etc)And you want to suppress them on and off.
Would there be a way to make an array 1-100 and just say suppress/unsupress "KepsNut" & array list of numbers.To basically add the two strings and find all the components in that array and turn them off or on.!
View 9 Replies
View Related
Mar 1, 2012
Can I use an iLogic Rule at the top assembly level to "replace all" of a particular component is that component resides in more than one subassembly? I need a rule to run and globally replace the component in all subassemblies without opening up each subassembly manually. I can run a rule in the individual subassembly that looks like the following:
If GoExcel.CellValue("3rd Party:Embedding 1", "Sheet1", "A2")=800 Then
Component.Replace("Part1:1", "OtherPartfilename.ipt", True)
End If
Is there a way to run a "replace all" command from a top level assembly?
View 1 Replies
View Related
Jul 26, 2012
I need to modify all the ipt in an assembly, but I don't kow how many ipt I have, and I don't know the name. Can I have with iLogic the list of all the ipt used in the assembly ? For example, to modify the Part Number in all the components.
The code should be like this :
For All component in Assembly
...
...
Next component
View 3 Replies
View Related
Oct 25, 2011
I'm using I-logic to suppress components in an assembly. I've attached a screenshot with 3 suppressed components.
In the browser the parts are suppressed but in the BOM (items 6,7,9) they are not. Is there a piece of code for this?
View 5 Replies
View Related
Oct 7, 2011
I am working on an iLogic assembly configurator that manipulates several skeletal parts, and suppresses both standard and skeletal parts depending on the configuration.
I've been using the Component.IsActive function to suppress all omitted parts, which has prompted me to create a custom Level of Detail. This hasn't caused me much grief until I had completed ~10months of work when it was time for me to make my final assembly drawing and a parts list.I am now running into several deal-breaking issues:
1) Suppressed parts insist on appearing on the Parts List.
2) Saving the assembly drawing reverts my assembly model to the "Master" LOD, which I never, ever, ever want to see again so long as I live.
Is there another workflow or technique that I should be using to turn off unwanted components in an assembly? I understand that LOD's are really intended to manage system resources, but Inventor users seem to be left with no other option to display a skeletal assembly in a certain configuration. What is the point of the Component.IsActive function if it doesn't update your assembly (at least so far as the Parts List is concerned)?
If I am left to deal with the nightmare that is the Inventor LOD, is there any way to set up the Parts List to reference the custom LOD?
Drawing View reps don't seem to be an option, as it looks like there is no way to automatically update the same custom view after the configuration has been made. The iAssembly Include/Exclude feature would handle part inclusion and BOM behavior nicely, but it won't fit into the rest of my iLogic and file management program.
View 9 Replies
View Related
Mar 25, 2013
I've been using iLogic. I'm creating a template assembly that will be used for multiple jobs. Therefore, the job number will be changing. I want a custom iProperty in ALL parts and sub-assemblies (cleverly call it "Job #" maybe) that I can include an a separate property called "Drawing #" which whose value will be [some text]-<Job #>-[some more text]. I want to be able to update all the "some text" parts manually for each component, but I want the Job # to update automatically. I need this property because I have a column in all my Parts Lists called "Drawing #" which tells the drawing number for any given part or assembly.
Ultimately what I want to do is open a text or Excel file, enter the job number, open my Inventor drawing, and have every Drawing # entry in every parts list magically update to the correct job number.
I've managed to use iLogic to do just that with a single .ipt/.iam file. But I have dozens upon dozens of components in the main assembly. I'd like to run some rule or hit some button or do something that will cause the Job # property to update for ALL sub-assemblies and parts, so that all my parts lists reflect the change.
View 4 Replies
View Related
Oct 6, 2013
Long time Autocad user but now am moving most of my work across to Autodesk Inventor.
Some of the work I do is with companies that their parts are standard components that will not change.
So I am using Inventor to automate the drawings based on their requirements. For example if it needs to be 4m high. then to use 2 x 2m sections. Currently I have create different assemblies of the different potential heights that I can switch between using ilogic but I need to be able to shift the top truss arch depending on how high the truss is.
View 1 Replies
View Related
Jan 24, 2013
I have an assembly which includes lot of parts (*.ipt) or sub-assembly (*.iam). I have some ilogic rules to control to suppress or un suppress them.
Now for the released assembly, I want delete all suppressed components by ilogic rule.
View 9 Replies
View Related
Jan 5, 2014
So I have been going round and round in circles on this one iam trying to use replace component within ilogic which is fine with switching one part for another but I want a drop down of parts so it replaces which ever one is active the problem I am having is establishing which one is active. So below is what I have so far but the problem is you cant seem to reference a part that is not in the assembly so I keep getting the error
The component named "Flange 1" was not found for example. I just need a way of establishing which one is currently in the assembly but with out referencing components that are not there.
If Component.IsActive("Flange 1")=True Then current = 1
If Component.IsActive("Flange 2")=True Then current = 2
If Component.IsActive("Flange 3")=True Then current = 3
If part = 1 And current = 2 Then Component.Replace("flange 2", "Flange 1.ipt", True) End If
If part = 1 And current = 3 Then Component.Replace("flange 3", "Flange 1.ipt", True) End If
If part = 2 And current = 1 Then Component.Replace("flange 1", "Flange 2.ipt", True) End If
If part = 2 And current = 3 Then Component.Replace("flange 3", "Flange 2.ipt", True) End If
If part = 3 And current = 1 Then Component.Replace("flange 1", "Flange 3.ipt", True) End If
If part = 3 And current = 2 Then Component.Replace("flange 2", "Flange 3.ipt", True) End If
View 4 Replies
View Related
Oct 18, 2013
After changing colors at assembly level only ,below is a rule that changes all parts that have material "Plywood" to poplar works great.
However I want a rule that does the same kind of change but on only temporally at assembly level only then we can change back to default colors by removing color override.
It would be good if we can do the following
Search assembly for .ipt files that have material that contains PlywoodChange to color using temporary override of "Clear - Light" Possibility of searching more materials within same rule ie : "Timber" to be black in color"Pvcu"to be white in color
Dim oCurrentDoc As Inventor.Document
Dim oDoc As Inventor.Document Dim oPartDoc As PartDocument
Dim oRefDoc As DocumentsEnumeratorDim oTargetColor As RenderStyleDim oNewColor As RenderStyleoCurrentDoc =
[Code].....
View 1 Replies
View Related
Sep 14, 2009
I'm using Inventor 2009.
Imagine a flat, rectangular plate with origin plains located symmetrically down the middle of the plate. Place a component, say a small cube, and constrain it to the face of the plate and the origin planes so that it too is symmetrically located. I now wish to pattern this cube about the midplane and create a total of five instances. I select "Pattern Component" in assembly mode and select the cube. For direction 1, I put in two instances and select an edge of the plate so that the pattern is taken to the left of the midplane. For direction 2, I again select two instances but pick an edge so that the pattern is taken to the right of the midplane. I now should have a total of 5 cubes but I don't. I have 6.
The second pattern is actually a repeating pattern of the first which, in the end, creates too many cubes. Visually, it looks correct because the cubes are placed excatly on top of each other. Numercially, like in BOMS, it is not correct.
Is there a way to avoid these duplications?
View 8 Replies
View Related
Feb 15, 2013
I was just wondering how to place a component into an assembly using ilogic? If this is possible, is there also an option to choose if iMates will be generated?
I would ideally like to place a list of components into an assembly, the list with probably exist in excel, then have iMates set to 'Automatically generate iMates on place' so that my assembly assembles automatically.
Inventor 2013 Certified Professional
Autodesk Inventor Professional 2011
Windows 7 Enterprise, 64-bit
View 7 Replies
View Related
Jul 9, 2013
I'm using iLogic to build a configurator and everything is working perfectly if I have all the componets available.
However, is there a way to use iLogic in this example:
Assume I have a bolt, nut and washer in an assembly based on 1/2" sizes. I then change the sizes to 1", the bolt and nut update to 1" but I do not have a washer modeled for 1". Is there a way to use iLogic to report that the washer is not available without causing an error or only updating the bolt and nut and ignoring the washer.
View 1 Replies
View Related
Oct 9, 2013
I'm having some difficulties with iLogic and reference parameters.
I have made a tube with a weird shape and I want to measure the longest length. So I have to cut the tube in a certain angle in relation with the center to measure the length.
The problem is that this angle is really hard to calculate.
So I tried making a rule where I can make my angle shift x degree and then measure the longest length. If the measurement is larger the previous measurement the angle will shift x degree again until the measurement is smaller than the previous.
So I made my starting angle 0 degree, I know this is for a fact not the longest length. And then I tried this rule. (before making a While rule).
And I noticed that on screen the measurement changes. But the reference - parameter stays the same. So it gives me the measurement on the starting angle & after rotating it again gives me the starting angle.
How can I get the parameter to update itself in between?
Dim measurement_length As DoubleDim measurement_length2 As DoubleMessageBox.Show("Start angle ", "My iLogic Dialog", MessageBoxButtons.OK, MessageBoxIcon.Asterisk, MessageBoxDefaultButton.Button1)angle_measurement_spec = 0RuleParametersOutput()InventorVb.DocumentUpdate()measurement_length = [code].....
View 1 Replies
View Related
Mar 8, 2013
I was wondering if there was a command that will get the file name of the model referenced in a drawing?
The reason I want to do this is because I have various programs to automate drawings, but I have to manually edit the code if i want to switch between using the code on assembly drawings and part drawings.
If i can get the model reference, I can then use a bit of extra programming to extract the extension. (i.e. .ipt or .iam)
Autodesk Inventor Professional 2011
Windows 7 Enterprise, 64-bit
View 5 Replies
View Related
Apr 12, 2013
I wish I perform the following code with iLogic. Is it possible to change a model parameter to a reference parameter?
If My_Expression Then' My dimension "d0" is a Driven Dimension' or' My dimension "d0" is a Reference ParameterElse' My dimension "d0" is NOT a Driven Dimension' or' My dimension "d0" is a Model ParameterEnd If
View 9 Replies
View Related
Oct 4, 2011
how to replace model reference using iLogic in inventor 2012. Basically I have a drawing file whose model reference needs to change with part number(iProperties) .
I've been struggling to perform replace model reference as there is no direct command given for it.
View 1 Replies
View Related
Aug 6, 2013
Is there a way in iLogic to iterate through all curves on a drawing. We manually apply radii labels to each drawing view but would like to automate the process with iLogic. How could I reference and cycle through all the radii on my drawing view?
View 2 Replies
View Related
Oct 26, 2011
Is there a way to set an assemblies bill of material setting to reference through iLogic?
View 3 Replies
View Related
Dec 11, 2012
How to reference the drawign sheet number using iLogic? I see on the snippets on the side a way to reference the sheet name, but I only want the number. To get the name it is ActiveSheet.Name, but ActiveSheet.Number does not work. Getting the name give something like ASSM:1, so if there was a way to take that and subtract the colon and everything before it that would work also. I am not a programmer, I've just taked some programs I found online and modified them a little to do what I want to do, but this is holding me back a bit.
Overall, I'm trying to modify the drawing view label to have a project number, referenced from the drawign iProperties, a view label, and sheet number, and then save that info in an iproperty of the part, and then reference that in the BOM so it automatically labels all of the views and fills out a column of the BOM to reference which page and view to find the parts of the assembly. I have everything working except for the sheet number.
View 5 Replies
View Related
Apr 2, 2013
I already have a code below that will read a bunch of drawing filenames that will go into each drawing, save the drawing, (print the drawing but I have this disabled for now,) close it, then move onto the next one.
What I want to do is add reference brackets around every dimension on each drawing. I have managed to update part list styles before using ilogic but I am not sure if it is possible with dimensions.
question = MessageBox.Show("Are you sure you want to update multiple drawings? If so, make sure all drawings are checked out.", "Batch Drawing Update",MessageBoxButtons.YesNo,MessageBoxIcon.Question)
'set condition based on answer
If question = vbNo
Exit Sub
End If
[Code] ......
View 4 Replies
View Related
Aug 31, 2012
how to suppress a pattern in *.iam by ilogic?
I used ilogic to suppress the main components, but the rest are not suppressed.
For example, I have component "A" and make it a pattern (Colum and Row are variable). How to use ilogic to suppress rest not just "A".
Autodesk Inventor Professional 2013 (64 Bit) SP2
Windows 7 Professional Service Pack 1
Intel(R) Xeon(R) CPU E5645
12.0 GB Memory
View 3 Replies
View Related
Jan 8, 2013
I have a pattern of holes (exactly 3) on an object and when the object height changes so does the pattern base on height. My issue is that i need to create a rule or code that ensures that apart from the first hole (which is fixed), the remaining two holes are at a location that is divisible by 6. The reason being that this is a sheet metal part and our punch press has a template for aligning punches at every 6 IN.
We are using iLogic to automate some of our designs and the code is needed to eliminate having to worry if the punches are at the correct location for faster production.
View 3 Replies
View Related
Oct 11, 2011
I've noticed that one can turn off the visibility of an entire component pattern by manually right-clicking the pattern in the browser and unchecking "Visibility". However, when one tries to automate this process with the following code, only the first element of the pattern is made invisible.
Component.InventorComponent("Pattern1").Visible = False
Is there a better way to do this, or will I be forced to develop a "workaround" like first changing the number of elements to 1?
I've been desperately trying to find a way to "turn off" unneeded assembly components without iAssemblies or LOD's, but Inventor always finds a way to stop me. This workflow of turning off visibility and setting BOM status to "Reference" would work if only I can make patterns invisible, also.
View 1 Replies
View Related
Apr 11, 2012
I attached the iLogic code which is automatically creating dwg drawing (script borrowed from one of the discussion group users), also it creates 4 views. I`m just wondering how to add flat pattern ?
View 7 Replies
View Related
