AutoCAD Inventor :: ILogic Rules - How To Replace All Components
Mar 1, 2012
Can I use an iLogic Rule at the top assembly level to "replace all" of a particular component is that component resides in more than one subassembly? I need a rule to run and globally replace the component in all subassemblies without opening up each subassembly manually. I can run a rule in the individual subassembly that looks like the following:
If GoExcel.CellValue("3rd Party:Embedding 1", "Sheet1", "A2")=800 Then
Component.Replace("Part1:1", "OtherPartfilename.ipt", True)
End If
Is there a way to run a "replace all" command from a top level assembly?
View 1 Replies
ADVERTISEMENT
Jan 5, 2014
So I have been going round and round in circles on this one iam trying to use replace component within ilogic which is fine with switching one part for another but I want a drop down of parts so it replaces which ever one is active the problem I am having is establishing which one is active. So below is what I have so far but the problem is you cant seem to reference a part that is not in the assembly so I keep getting the error
The component named "Flange 1" was not found for example. I just need a way of establishing which one is currently in the assembly but with out referencing components that are not there.
If Component.IsActive("Flange 1")=True Then current = 1
If Component.IsActive("Flange 2")=True Then current = 2
If Component.IsActive("Flange 3")=True Then current = 3
If part = 1 And current = 2 Then Component.Replace("flange 2", "Flange 1.ipt", True) End If
If part = 1 And current = 3 Then Component.Replace("flange 3", "Flange 1.ipt", True) End If
If part = 2 And current = 1 Then Component.Replace("flange 1", "Flange 2.ipt", True) End If
If part = 2 And current = 3 Then Component.Replace("flange 3", "Flange 2.ipt", True) End If
If part = 3 And current = 1 Then Component.Replace("flange 1", "Flange 3.ipt", True) End If
If part = 3 And current = 2 Then Component.Replace("flange 2", "Flange 3.ipt", True) End If
View 4 Replies
View Related
Mar 29, 2011
I am currently using a vb.net application to control inventor using the API code.The API code is used to delete/suppress unwanted occurances from parts and sub-assemblies, depending on what is selected in the external application. It then puts all the parts and sub-assemblies together into a final assembly.
Most of the parts contain iLogic rules, to control dimensions, and these have been set to trigger when the part file is opened.I have noticed that in my final assemblies some of the parts don't appear as they should, however if i close the final assembly and open the individual part it appears to be correct. If i then open the final assembly it looks fine.
I think this might be due to the iLogic rule being triggered when the part is opened.Is there any way to trigger the rules using the API code while the final assembly is open, instead of closing it down and opening all the component parts and sub-assemblies?Or should we set the rules to trigger on a parameter change?
View 6 Replies
View Related
Jul 23, 2012
I'm trying to set a rule in which i have 2 i parts that i can change the length of . I want a rule where if i change one of them it changes the other to fit with it.
View 1 Replies
View Related
Oct 1, 2012
I made a simple rule that triggers before save to ask user to make a selection, which then updates an iProperty.I created A multi value fxParameter and used the InputListbox function.
Ultimately I want to know the best way ok making this rule available to all parts, old and new.I am thinking, it will be easy enough to update my templates and embed this code into the part, as well as content center files by updating each file / template .
But for existing parts, is there a way to add these rules without the user having to do much steps.because there is an fxParameter I am thinking the user will have to know how add this to their part.I can change it to just an input box where they can type in the correct value, if that would be easier.
View 6 Replies
View Related
Sep 8, 2011
I have been having trouble with parts that do not trigger iLogic rules. I've set the triggering events to After Open Document, but nothing triggers. I must manually open the parts and then click the iTrigger to get the rules to run. This is not all parts only a select few and seemingly random.
Is there something I can do to ensure the triggers fire and the rules to run?
Sidebar: If a part is set for trigger After Open Document should that part trigger the rules when the assembly that the part is in is opened?
View 9 Replies
View Related
Oct 3, 2011
I am very new to this whole concept of having ilogic based rules to drive your part design. I have even gotten as far as creating a ipart and having ilogic rules be able to suppress, unsuppress, change values and dimensions using ilogic rules. I now want to be able to use ilogic rules to drive some of the various(yet similiar) assemblies that I create all the time.
For instance, If I have just a flat plate as the base component with a shaft welded to it that varies in length for my assemblies. Since the shaft varies in length, I went ahead and created iparts for all the lengths of the shafts. I can manually change which shaft I want represented in the assembly, but I would like to to know how do I get Ilogic to place the different shafts based on user parameters???
I've looked into component place iparts, but can't seem to get the code to work. The list of iparts tree within the model doesn't pop up in the model tab in the ilogic rule, only the base component.
View 1 Replies
View Related
Apr 24, 2013
I would like to know if there is any possibility to replace a component with another one, that has a different internal name. Losing the dependencies would be acceptable.
ReplaceReference and PutLogicalFileNameUsingFull always return the error "wrong parameter".
View 5 Replies
View Related
Jul 5, 2012
We have some Problems with the running order of iLogic Rules.
I try to describe it in an Example, you can find attached. (The description (PDF) and the ipt-file)
We're using iLogic via Addin in Inventor 2010. But I also tried it, with the 2012 version (the same problem).
The attached IPT File is running in the correct order.
View 2 Replies
View Related
Apr 1, 2012
I am trying to build a set of scripts (aka iLogic rules) into templates. So far, quite a common task. One extra requirement is that the scripts need to be updatable after parts have been instanciated from the template. That is, we do not want to update all of the ipt each time a new material option is added to the script. That means that external rules are the only way to go, right? This is the road I tried and it seems to work on my machine.
One extra requirement is that the whole project must be shared between several workstations. We went the Subversion road for that (for all the Vault comments). The scripts are distributed properly and in the same absolute location on the two test machines, all good (I checked the md5 on both side and they all match). The application options on all the machines are all set the same way (export the xml file, check it in the source control, import on all the machines restart). The iLogic search path is also updated, but manually this time, since it is not included in the application options export. It should all work perfectly right? Well, sort of....
I did create a tiny assembly from the templates. On my source machine, all looks good. The ilogic rules are both listed in the ilogic browser and the triggers are set when I instanciate from the template. This is the intended behavior. Now, I close inventor, copy the whole directory to a new machine, open inventor there and open the project. The rules do not appear anymore in the browser, but they are still listed in the trigger list (wtf?). The best part is that if I do not touch anything, stuff still works! The scripts are found and run properly!! Now, if I have to change the triggers or even find the rule in the browser to run it manually, well, bad-stuff-happens (tm).
All the files in question are indentical on both machines, the ilogic files, the ipt files, the application options export, all with the same hash. The ilogic search path is also set the same as are the absolute paths. It should work the same (tm).
Me sending a copy of the files is not likely to work though. Since the problem happens when you copy. I could try to "pack and go", but that would break reason #1 for doing that, which is keeping only one version of the script and adding materials at only one place for all the projects.
View 4 Replies
View Related
Nov 29, 2012
I have 3 iLogic Rules that I use with my idw's,
1-SCALE - is to update scale in the title block
2- WEIGHT - is to update weight of model in title block
3- PDF - is to create a pdf version of drawing in same location as idw
all are triggered by saving the drawing.
These work fine, but sometimes when I create specific types of drawings there is errors, which is no big deal, just a prompt appears and I press ok and everything is fine.
With very little to no iLogic programming knowledge, is there a way to edit to rules so that if there is an issue, the rule knows it is ok and saves without the little prompt appearing?
Example of when errors occur for:
SCALE - sometimes I create drawings on my template just using create sketch, I don't place a base view so therefore there is no model information. which makes it hard to produce a scale. (see image, error -1)
WEIGHT - occurs during the same instance as above, only a sketch is saved on the idw. (see image error -2)
but I also have an error occur when creating a drawing from a presentation file. I create a presentation file from a specific level of detail from an assembly. and I get an error when saving . (see image error-3)
I understand the first 2 errors because there is no physical data to get this information from, so I am hoping an edit to the rules can bypass this issue. But the 3rd error doesn't make sense. It is from an actual model, but I guess the physical properties get lost from an .iam to .ipn?? or is there a setting that can be toggled to carry over model properties?
Inventor Pro 2013
Rules are below:
'Scale
Public Sub Main()
On Error Resume Next
'Get the drawing document
[Code]....
View 6 Replies
View Related
Aug 18, 2011
Is it possible to create something like a password or other trick to protect ilogic rules from editing? Ilogic can enforce standards but if any engineer can delete rules or edit them then we have a problem.
View 4 Replies
View Related
Jul 31, 2013
I have a dedicated folder for external rules on a network. In the Advanced ilogic configuration interface on my machine I added the path to this folder in the External rule directories.That seemed to work fine. I opened the ilogic tree activated the external tab and the external rules were available for selection.
Today I tried to do the same process however no rules were visible under the external tab. I had to select "add external rule" and navigate to the folder.I do not want my users to have to manually navigate to the folder. Is there a step i have missed in this process? I am using Inventor/ilogic 2009.
View 9 Replies
View Related
Mar 25, 2013
In past I replaced components in Assemblies with this sub:
Sub testReplacePartInAss()
Call ReplacePartInAss("W:INVENTORTPart1.ipt", "W:INVENTORTPart2.ipt")
End Sub
[Code] .....
But if the assembly is a weldment assembly the line
If oOcc.ReferencedDocumentDescriptor.FullDocumentName = sInAssFilename Then
creates an error '91' that the object is not set.
What has to be changed in this code so that it will work with 'normal' assemblies AND weldment Assemblies too.
View 3 Replies
View Related
Aug 23, 2012
How do I change the document units using iLogic rules.
View 3 Replies
View Related
Feb 29, 2012
How do I turn sketch visibility on and off using ILogic rules.
View 3 Replies
View Related
Mar 27, 2013
I have an assembly with parameters named the same as LOD's.
The parameters are set to equal the mass of the corresponding LOD's using ilogic.
If the LOD does not exist, I want to set the mass of the corresponding parameter to a value of zero.
I don't know how to check for the existence of the LOD and I'm not sure I can have three commands in the ELSE section.
Below is an example of what I need using a Parameter and LOD called EXTERNALS as an example.
If EXTERNALS LOD does not exist
THEN Parameter("EXTERNALS")=0
ELSE
'activate the EXTERNALS LOD
ThisDoc.Document.ComponentDefinition.RepresentationsManager.LevelofDetailRepresentations("EXTERNALS").Activate
[code]...
View 2 Replies
View Related
Mar 7, 2013
I am having a problem with Inventor 2013. Every time I run/edit then run an iLogic rule my Inventor crashes. I have sent the report in to autodesk, but I need a fix for now.
I have tried a soft reboot, hard reboot, only opening inventor while no other programs are running, disconnection from the internet, etc.
View 1 Replies
View Related
Dec 5, 2012
I'm a contractor, I've created a really impressive form-driven assembly containing various iLogic rules. However, as i add more rules it is beginning to slow down (increase rule processing time). Should I suggest upgrading to 64-bit and increasing RAM?..could be costly with no increase in performance.
Processor: i7-2600
OS: 32-bit
RAM: 4.00GB
Inventor 2012
View 2 Replies
View Related
Aug 10, 2012
I made an Part with iLogic rules, let's call it "iLogicPart". The rules inside could create lot of different part by my input.
I want save the different parts to different name as "Part 1", "Part 2", etc. I used SaveAs to get them.
My question is: I want to delete all rules and parameters in the saved parts as "Part 1", "Part 2". And I have lot of features (the name is hard to track) which are inactive, I want to delete them at same time too.
I could manually do so, but I want to use rule to do so automatically.
View 9 Replies
View Related
Nov 22, 2013
I am just starting to use ilogic for some design files. We have two design sites connected with Vault Collaboration 2012.
What is the best practice for sharing the ilogic rules between the sites?
I was planning on making an ilogic rules folder at the root of my workspace and having Vault manage the external rules. However, I don't see the rules listed when I check-in a file that uses them.
Do I have to add the rules to my template files? If so, how do I make changes to the rules without editing every file created with the templates?
We will be moving to Vault and IV 2014 after the first of the year, if that makes any difference.
View 7 Replies
View Related
Jul 17, 2013
I have a wire trough that we typically use on all our units. Instead of modelling each trough as it's own separate part to length, I would like to add this part to frame generator for tracking there cut lengths etc...
A few items, there is two sizes that we use, but for now I will work with just one.
I have modeled the part and renamed the important parameters.
-WIDTH - stays the same
-HEIGHT - stays the same
-LENGTH - adjusted by frame generator
-RIBS - the part has 6 currently, but there is a rib added for every 1/2 inch. it is a rectangular pattern
-SLOTS - will be added to the trough every 2 inches of length, it is a rectangular pattern
-SLOT_DISTANCE - is 2 inches and never changes, if the trough is cut on a slot, which ever is easiest, to show half a slot or none, doesn't matter, this is just for a visual and BOM reference
I found a video that shows me how to publish parts to FG, but I am stuck for the iLogic part. Part attached.
Inventor Professional 2014-Update 2 - AutoCAD Electrical 2014
Win7-x64 | ASUS P8Z77-V | i7 3770 -3.4 GHz | 32GB RAM |
240GB SSD | nVidia GTX 670 4GB - 320.49
View 6 Replies
View Related
Sep 26, 2012
I'm currently trying to make an automated fence generator with Inventor 2012 driven by iLogic rules.
My model is done now, and my BOM information (description & part number) is set correctly.
Now is my problem some parts are not supposed to be in the BOM at a certain moment.
Example.
If fence_type = 1 Then
Beam-001 = default
Else If fence_type = 2 Then
Beam-001 = reference
Else If fence_type = 3 Then
Beam-001 = reference
End If
But what do write to set BOM status of a part?
Inventor 2013
View 5 Replies
View Related
Jan 29, 2013
I'm new to inventor and I need to be able to create coppies of a part in my assembly that are uniquely identified so they can be individually changed. I see that this can be done through the ribbon with the "Place iLogic Component" button, but is it possible to do this from the API in a rule?
I am using inventor 2012 pro.
View 2 Replies
View Related
Jul 10, 2012
Lets say you have 100 Keps Nuts in an assembly. Named (KepsNut1,KepsNut2, etc)And you want to suppress them on and off.
Would there be a way to make an array 1-100 and just say suppress/unsupress "KepsNut" & array list of numbers.To basically add the two strings and find all the components in that array and turn them off or on.!
View 9 Replies
View Related
Jul 26, 2012
I need to modify all the ipt in an assembly, but I don't kow how many ipt I have, and I don't know the name. Can I have with iLogic the list of all the ipt used in the assembly ? For example, to modify the Part Number in all the components.
The code should be like this :
For All component in Assembly
...
...
Next component
View 3 Replies
View Related
Sep 17, 2012
I have a pattern of reference components, but the quantity of the pattern can change based on certain criteria. When the quantity increases or decreases, I need each pattern element to have its BOM structure set to reference.
The problem is, even if the original pattern element is set to reference, each subsequent element comes in as normal. This causes the BOM quantities for that component to be reported incorrectly in higher assemblies.
Is there some iLogic or VBA code that will automatically set each component in a pattern to BOM structure "Reference", even if the pattern quantity changes?
View 7 Replies
View Related
Oct 25, 2011
I'm using I-logic to suppress components in an assembly. I've attached a screenshot with 3 suppressed components.
In the browser the parts are suppressed but in the BOM (items 6,7,9) they are not. Is there a piece of code for this?
View 5 Replies
View Related
Oct 7, 2011
I am working on an iLogic assembly configurator that manipulates several skeletal parts, and suppresses both standard and skeletal parts depending on the configuration.
I've been using the Component.IsActive function to suppress all omitted parts, which has prompted me to create a custom Level of Detail. This hasn't caused me much grief until I had completed ~10months of work when it was time for me to make my final assembly drawing and a parts list.I am now running into several deal-breaking issues:
1) Suppressed parts insist on appearing on the Parts List.
2) Saving the assembly drawing reverts my assembly model to the "Master" LOD, which I never, ever, ever want to see again so long as I live.
Is there another workflow or technique that I should be using to turn off unwanted components in an assembly? I understand that LOD's are really intended to manage system resources, but Inventor users seem to be left with no other option to display a skeletal assembly in a certain configuration. What is the point of the Component.IsActive function if it doesn't update your assembly (at least so far as the Parts List is concerned)?
If I am left to deal with the nightmare that is the Inventor LOD, is there any way to set up the Parts List to reference the custom LOD?
Drawing View reps don't seem to be an option, as it looks like there is no way to automatically update the same custom view after the configuration has been made. The iAssembly Include/Exclude feature would handle part inclusion and BOM behavior nicely, but it won't fit into the rest of my iLogic and file management program.
View 9 Replies
View Related
Mar 25, 2013
I've been using iLogic. I'm creating a template assembly that will be used for multiple jobs. Therefore, the job number will be changing. I want a custom iProperty in ALL parts and sub-assemblies (cleverly call it "Job #" maybe) that I can include an a separate property called "Drawing #" which whose value will be [some text]-<Job #>-[some more text]. I want to be able to update all the "some text" parts manually for each component, but I want the Job # to update automatically. I need this property because I have a column in all my Parts Lists called "Drawing #" which tells the drawing number for any given part or assembly.
Ultimately what I want to do is open a text or Excel file, enter the job number, open my Inventor drawing, and have every Drawing # entry in every parts list magically update to the correct job number.
I've managed to use iLogic to do just that with a single .ipt/.iam file. But I have dozens upon dozens of components in the main assembly. I'd like to run some rule or hit some button or do something that will cause the Job # property to update for ALL sub-assemblies and parts, so that all my parts lists reflect the change.
View 4 Replies
View Related
Oct 6, 2013
Long time Autocad user but now am moving most of my work across to Autodesk Inventor.
Some of the work I do is with companies that their parts are standard components that will not change.
So I am using Inventor to automate the drawings based on their requirements. For example if it needs to be 4m high. then to use 2 x 2m sections. Currently I have create different assemblies of the different potential heights that I can switch between using ilogic but I need to be able to shift the top truss arch depending on how high the truss is.
View 1 Replies
View Related
