AutoCAD Inventor :: Ensure Vault Ribbon / Addin Loads Within 2011?
Aug 13, 2013Is there an easy way to ensure the Vault ribbon/addin loads within Inventor 2011?
AutoCADM 2011 SP2
XP 32-Bit SP3
ADVERTISEMENT
AutoCAD Inventor :: Communication Error With Vault Addin
Sep 9, 2013Using Inventor 2014 and Vault Basic 2014. It was working this morning but now when Invnetor is opened it automatically logs into Vault and says it is successful but the open from vault icon is greyed out. Similarly when opening a drawing from the vault it used to automatically run and open inventor but now seems to lack the connection. Even when manually opening a drawing that is in the vault by downloading it from the browser and then opening in inventor there is no Vault tab on the browser and all Vault commands except "log out" are greyed out. I think it has something to do with the add-in as well as the Vault group.
View 2 Replies View RelatedAutoCAD Inventor :: 2013 Vault Addin Could Not Find Data Management Services
May 9, 2013I was getting this error on one of my users machines, inventor 2013 vault add in could not find the data management services
I uninstall Vault workgroup 2013, Inventor 2013, re install, and re install add ins, worked for half a day, and just got the same error again,
it seems As Inventor looses the add in, what was intersiting it gave an error about some unerlaying error after disgarding that, the add in doesnt work anymore.
I also cant copy design from vault on the same machine, all Inventor related files cant be copied, but dwg files can.
I get the feeling its an Inventor issue, my last resort is a clean install.
AutoCAD Inventor :: 2013 Addin Icon Size On Ribbon Is Wrong?
Apr 19, 2012The icon dispayed on the ribbon for my addin seems to be the large (32x32) icon and i'm not sure how to fix that.
In IV2012 it was fine and i can't find anything in the programming that suggests anything was changed.
Using IV2014 Pro SP1 update 1, Win7-64bit
AutoCAD Inventor :: Vault Ribbon Missing?
Dec 2, 2011All of a sudden I see that within my Inventor the vault Collaboration ribbon has disappeared. How do I bring this back?
C1
Inventor Professional 2013
Vault Collaboration 2013
AutoCAD Inventor :: Vault Tab Disappears From Ribbon
Jun 5, 2013When I open up Inventor 2014 the Vault tab is visible in the ribbon; however, when I create a new file (of any type) the vault tab disappears from the ribbon. I can retrieve it by right clicking on the ribbon, clicking ribbon appearance and selecting reset ribbon. This fix is only temporary because if I close out Inventor and re-open it I must go through the same steps to retrieve the Vault tab in the ribbon. Any way to make it stay in the ribbon so I don't have to reset the ribbon every time?
After digging a bit more I came across the answer: [URL]....
AutoCAD Inventor :: Map Folders On Vault Ribbon Is Grayed Out?
Apr 22, 2013I am very new to Autodesk products, I never used any of them before. I just purchased a student license and I downloaded Inventor Professional. This is the 2013 version, 64 bit edition. I also downloaded Vault Basic 2012.
I am trying to learn how to use these tools and one step in this process is to map the working folder in Inventor to Vault so files can be checked in and out, so I created a new vault, added users and groups, and that went without any problem.
Then, in Inventor I log in to this new vault. All the other buttons, (Open, Place, Check In and Check Out) are grayed out at this time. Reading the literature, I got the instructions to click on the Vault ribbon in Inventor, then on Access and "Map Folders". But at this point I cannot proceed because this menu item is grayed out as well.
AutoCAD Inventor :: Vault Ribbon / Browser Not Working
Jun 25, 2012I have noticed today that my Vault ribbon is not working. I can log in / log out of the Vault and navigate to the Vault explorer. Also in the browser I only have access to model and favorites. It acts like the Vault project is not active.
The project file is active and mapped properly and I can check files in and out via the Vault explorer. I have also installed updates dl19384851 and update 1 for Inventor.
I am running Windows XP Pro x86 & Vault Professional.
AutoCAD Inventor :: Vault Icon Missing From 2013 Ribbon?
Apr 17, 2012Just installed inventor 2013 and the icon to launch vault is missing from the ribbon where it used to be in v 2012. Also when i try to open a file the quick link to vault is not there. i have installed vault basic 2013 and it opens up fine and my files are in it. Do i have to create a link?
View 2 Replies View RelatedAutoCAD Inventor :: 2014 Pro Addins Not Loaded Vault Ribbon Missing?
Sep 27, 2013Since yesterday The vault ribbon is missing in Inventor 2014 and also add ins are grayed out(not loaded).
win 7 x64 system?
AutoCAD .NET :: Start Addin That Add A Ribbon On Start Up
Apr 18, 2012I have a VB .NET Dll that add a new ribbon in AUTOCAD.When I load this dll from AUTOCAD, this new ribbon is well added.I'm trying to start this dll with AUTOCAD Start.
I've tried to load the DLL from the acad.lsp but the DLL is loaded before AUTOCAD load the ribbon, then the dll is well loaded but my new ribbon is not displayed !.
AutoCAD Civil 3D :: 2011 - Will Not Display Ribbon
Feb 11, 2013I am using Civil3d 2011 and the ribbon will not display. The button seem to work some times but I can't see the ribbon, QAT, or Infocenter. I tried relaoding the CUI files, updated video card drivers, Civil3D patches, even uninstalled and reinstalled Civil3D.
I can turn the ribbon off (ribbonclose) and the ribon area is rendered correctly on the screen. I can turn the menubar on/off and it works just fine.
I tried logging on to the computer as different user, as the administrator, etc. Same error.
I use the Ribbon but now I can't because I can't see it.
I have attached a screen shot of the ribbon area.
AutoCAD Civil 3D :: 2011 Will Not Load Enterprise Ribbon In Workspace
Aug 14, 2012I have a cuix setup as an enterprise menu. The drop-down menu loads up fine in my workspace. However, when i go to customize the workspace, and add the ribbon portion of the cuix, it fails to load it. The same enterprise menu loads fine in AutoCAD 2011.
View 1 Replies View RelatedAutoCAD .NET :: Create Custom Ribbon Tab And Buttons For Mechanical 2011?
Nov 23, 2010How do I create a ribbon tab and button for my application, any sample code?
How do I interact the button click with my application?
AutoCAD Architecture :: Create New Custom Tab Panels In Ribbon 2011
Oct 15, 2011send me a link to tutorial to create a new cutom tab panels in a ribbon 2011
View 1 Replies View RelatedAutoCad :: 2011 - Display Large Icon Without Text In The Ribbon?
Oct 22, 2012Is there a way to display large icon without text in the ribbon in autocad 2011? or this feature is only available in 2012 and up.
Is there a workaround to display large button icon without text in 2011?
AutoCAD LT :: Content Panel Missing From Insert Tab On Ribbon 2011?
Jan 28, 2011In looking for the design center in autocad 2011lt I discovered the content panel where it should be nested is missing in the insert tab on the ribbon
View 3 Replies View RelatedAutoCAD Inventor :: Run Addin From VBA Macro
Nov 9, 2011How to call a addin from vba ? The addin is existing, source code not available :-(
My only idea is to somehow activate the button on the ribbon. Made a dump with the Print Ribbon routine from the online API help:
Tab: CDLIGHT, CDLIGHT.Part.Tab
Panel: iToolbox, CDLIGHT.iToolbox.Part.ToolBar
AutoCAD Inventor :: Force Command In Loads Panel
Oct 10, 2013When I click the Force command in the LOADS panel when doing a Frame Analysis, I don't get a dialog box. All I get is a select origin box with an arrow. There is no way to change the Magnitude value or the Angle of Plane as per instructions in the tutorial. I have tried numerous ways to get a dialog box to appear, but I can't find out how. why I am not getting a Dialog box?
View 1 Replies View RelatedAutoCAD Inventor :: Frame Analysis UDL And Point Loads
Oct 10, 2012I understand that in a normal part to apply a load to a face is to make it a UDL (uniformly distributed load) by default. To apply a point load, I was told to create a small sketch and use it to split a face to create, in effect, a small face on which to apply a load, effectively making it a point load.
Now in the frame analysis environment, there is clearly an option for 'force' and one for 'continuous force' which the description clearly describes as a uniformly distributed load. However, when I run the simulation (on a 2m long 100mm x 50mm x 4mm Rectangular hollow beam) with a normal load in the middle of the beam (1m offset); the maximum moment comes out at 500000 Nmm or 500 Nm. By my reckoning the moment should be 1000 Nm as the basic formula for a moment from a point load is M = F*D (Moment = Force * Distance). However, to get 500 Nm, it looks like Inventor is using M = (F*x^2)/2 where x is the midspan of the beam (in this case 1m). .is a normal load in frame analysis the same as a UDL? If so..how to I make it a point load?
There are also some errors stating instability of type 2 at various nodes, I've used both Pinned and Floating constraints at either end of the beam.
AutoCAD Inventor :: Simulation Missing Applied Loads
Oct 11, 2011I was running a simulation with success including gravity and applied loads. I was checking both stresses and deflections. Both were in line with what I was expecting. The next day I went to change a few dimensions and run it again. The stresses and deflections were significantly less than expected (I did not tweak the dimensions very much). I changed my dimensions, remeshed and ran it again. It worked fine and returned expected results. I continued in this manner tweaking the size of my box.
Finally I went for one last run.... it didn't work again. It returned the significantly less than expected results. A bit of investigating revealed that it is only applying the gravity loads during the simulation. All of the applied loads are being disregarded (however, they show up in the report as if they are being applied.) If I supress the gravity my stress and deflections return 0 values. I have tried taking my loads off and reapplying them. I have tried removing the gravity load. I have remeshed. I have inputted my loads and the gravity in different orders. I cannot get my simulation to calculate using my applied loads. It was working fine.... what happened?
AutoCAD Inventor :: Getting An Addin To Load Without Registry
Sep 22, 2011how to load an addin without using the registry for Inventor 2012? Failing that, I just can't seem to get it to work.
View 1 Replies View RelatedAutoCAD Inventor :: Example Of Embedding IronPython Into A C# Addin
Dec 13, 2012Below is a link to a github repo that has a code example showing how to embed an IronPython engine inside a C# addin. It is the same as the "Simple AddIn" that comes with the SDK, only with the logic part of the addin factored out into IronPython. I could never find anything on using IronPython with Inventor so I'm posting this for any others that might be interested.
The main reason for doing this is to speed up development time. Edits related to the python code do not require the cycle of shutting down Inventor, compiling, restarting etc. More detail is in the readme. URL....
AutoCAD Inventor :: AddIn Sample Tool Bar
Oct 29, 2004I followed exactly step-by-step showing in the program. After compile the DLL register the registry, run IV, I couldn't see the AddIn SampleToolbar in the Panel bar.
View 9 Replies View RelatedAutoCAD Inventor :: Calling AddIn Function From Outside
Dec 17, 2013I would like to make an Inventor AddIn with commands (functions) that can be called from other standalone applications. I have tried to create a COM interface for my AddIn, and that works with rather small effort, but I think I have heard that it should be possible to do this without the COM interface. I would like to avoid COM if possible. if I need to do anything special in the AddIn to make the function visible and how I on client side calls the function.
View 1 Replies View RelatedAutoCAD Inventor :: Creating An Addin That Uses WPF (instead Of WinForms)
Jan 27, 2010creating an Inventor addin that uses WPF (instead of WinForms). We are trying it with Inventor 2010 and are running into problems.
View 2 Replies View RelatedAutoCAD Inventor :: Reload An Addin For Each File
Feb 13, 2013I have an addin which displays a form, then when I click a button operations are launched. The form is no modal, so I display it, select objects, apply, select objects, apply,... then close the form with another button (form.close).
All functions, but only on the first opened file : I open the file, use the addin, close the form. I open another file, the addin is always loaded, but when I click on the icon to display the form nothing happens... I have to unload the addin and reload it.
AutoCAD Inventor :: Addin Stopped Loading
Apr 13, 2012Windows 7 64bit
Inventor 2010
Visual Studio Professional 2010
I have an Addin with several pieces of functionality that I have been working on for over a year now and have had no problems with it loading. Yesterday I was working on a bug in a function and when I set a break point it was not breaking in the correct location. Possably some miss match between the source and .pdb files. I tried a clean build but still could not get the break point to be correctly aligned with my source code.
I tried to unregister and re-register the Addin with regasm but no luck. I then decided to search the registry for the name of my Addin and was supprized to find thousnads of registry entries. I then decided to clean my registry of all occurances of the Addin name. After removing all occurances of my Addin from the registry my Addin would not load.
I tried putting a message box in the first line of the Activate sub but it never executes. I made the assumption that it was a problem with the registry and changed the GUID value. When I did a rebuild I got the following error:
Error 1 The "UnregisterAssembly" task failed unexpectedly.
System.Runtime.InteropServices.COMException (0x80030002): could not be found. (Exception from HRESULT: 0x80030002 (STG_E_FILENOTFOUND))
at Microsoft.Build.Tasks.NativeMethods.UnregisterTypeLib(Guid& guid, Int16 wMajorVerNum, Int16 wMinorVerNum, Int32 lcid, SYSKIND syskind)
at Microsoft.Build.Tasks.UnregisterAssembly.Unregister(String assemblyPath, String typeLibPath)
at Microsoft.Build.Tasks.UnregisterAssembly.Execute()
at Microsoft.Build.Framework.ITask.Execute()
at Microsoft.Build.BackEnd.TaskExecutionHost.Microsoft.Build.BackEnd.ITaskExecutionHost.Execute()
at Microsoft.Build.BackEnd.TaskBuilder.ExecuteInstantiatedTask(ITaskExecutionHost taskExecutionHost, TaskLoggingContext taskLoggingContext, TaskHost taskHost, ItemBucket bucket, TaskExecutionMode howToExecuteTask, Boolean& taskResult) AnthroAddIn
I ran the build again and did not get the error.This Addin is loaded on every CAD workstation in the company using an install program written with the Inno Setup Compiler. I installed the Addin using the installer and the Addin still will not load on my machine.
What is the best approch to debugging an Addin that will not load?When is it necessary to re-register your Addin using regasm?Is it possable that this problem is being caused a problem with the registry?I have read a number of posts regarding problems with Addin's not loading but have not found anything simmilar to this.
AutoCAD Inventor :: How To Pass Variable From One Addin To Another
Aug 25, 2013I've used vb.net to write two separate addins. I was wondering if there is a way to pass a variable from one addin to another similar to the way shared variables are passed from rule to rule in iLogic.
View 2 Replies View RelatedAutoCAD Inventor :: Unable To Get Addin To Load
Aug 25, 2011I have having difficulty getting any addins to load at the moment and am totally stumped as to what the problem is. I have even created a very simple addin from the (C#) template, compiled and registered it and it still will not load up. I get the addin to appear in the Inventor Add-ins dialog ok but it will not load for some reason. I have tried generating various .Net versions 2.0, 3.0 & 3.5 all produce the same result. I have also tried to debug the add-in by getting Visual Studio to launch Inventor but it does not even appear to be loading the add-in. I have dug out some work I did months ago and tried that but it does not work either. Is there a log in Inventor?
I am using C# in Visual Studio 2008 Pro & Inventor 2011.
AutoCAD Inventor :: Create Addin With Compatibility
Sep 12, 2013I am looking for any example to create an addin compatible between versions of inventor and also compatible win between 32 and 64bit.
Today I know create all separate. Thereby generating 4 different files.
Example:
Addin2013_32x.dll
Addin2013_64x.dll
Addin2014_32x.dll
Addin2014_64x.dll