All of the patterned parts in my assembly show up as reference parts in the BOM I have I have opened the base part for the pattern and made sure its BOM is set to normal. When I change the BOM setting in the assembly it automatically changes to reference.
View 2 RepliesI am having trouble with getting the reference parts of my assemblies to show on the IDW drawings. That is, most of them show, but some items disappear.
On the attached picture you can see what i mean... its of a circular structure with a door frame mounted. One is put in as normal assembly, one is put in as reference part.
The circular structure shows, but the door is missing (in some views). When I do a sectional view of the view where it is missing it appears.
I had some parts that in BOM were checked as "referenced". Then at some point I changed them to "normal".
In the drawing environment they still act like reference parts even though I changed them to "normal" before created the view.
They are still see thru when I go Drawings View/Model State/Reference data/As parts. They act like they are reference parts but they are not anymore. How to make then really "normal"?
I have an assembly that uses reference parts. I do not want them in the BOM, but they are used in other drawings in the BOM. When I make them reference, the iso drawing view boundaries are not correct. Can I change the size? Crop will only decrease the size not increase?
View 3 Replies View RelatedI am doing a .idw drawing of an assembly that I have several parts that I do not want to appear in the BOM parts list. I have therefore set these parts as Reference parts however this has caused them to appear as "hidden type" lines in the drawing and are even visible through other parts.
Is there any way to make these parts appear in the drawing "as normal" and not be listed in the parts list?
In a drawing Is there anyway to section (and show the hatch pattern) on reference components?
View 9 Replies View RelatedI am trying to find a simple way to center part(s) to some reference within an assembly such that if any part sizes are changed, then the assembly will stay symmetrical when updated. I would imagine that this is simply possible without adding any constraint containing a numeric value.
See attached part and assembly files showing a 4 piece frame with the angles unconstrained NE to SW. All i want to do is maintain symmetry of the frame if any parts sizes (cross-sectional or length) are changed. I've tried to add a centered plane to the angle and aligning that with a sketch point made in the assembly but i can't select any sketch features when i try to apply an assembly constraint.
When a drawing view is made within Inventor from a presentation file (.ipn) some of the parts sometimes donot appear as properly visible.
I have attached some screen shots which might lead to some clues.
I made a flanged connection using I logic. Very simple Tube + Flange + Gasket + Blind flange + Bolting.Then I tried to write some ilogic rule to have Blind flange on / off when needed, hence the Gasket & Bolting also need to be off. Like in these images:
That works fine visually, but I also want the BOM to be set accordingly. For the Blind flange & Gasket my BOM is OK. But for my bolting the BOM is not OK. I tried to set the BOM structure the same way as the visibility but that failed. It only subtracted 1 bolt from my list (see code)
If Blindflange_status = 0 Then 'Bolting offComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kReferenceBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = FalseElse 'Bolting onComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kDefaultBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = TrueEnd If
Is there a way to set all parts within a pattern BOM structure? I made my bolting by adding 1 bolt, 1 washer & 1 nut and then pattern them using feature pattern select.
Inventor 2013
How can you force the geometry of reference parts to print behind to print behind your visible parts. I have my reference parts print out on a light gray layer to be shown indistinct on a drawings, but it prints over my object lines in effect hiding them. This is even true if a reference part is hidden. Then hidden line will print over the object lines as well.
View 4 Replies View RelatedI made a flanged connection using I logic. Very simple Tube + Flange + Gasket + Blind flange + Bolting.
Then I tried to write some ilogic rule to have Blind flange on / off when needed, hence the Gasket & Bolting also need to be off. Like in these images:
That works fine visually, but I also want the BOM to be set accordingly. For the Blind flange & Gasket my BOM is OK. But for my bolting the BOM is not OK.
I tried to set the BOM structure the same way as the visibility but that failed. It only subtracted 1 bolt from my list (see code)
If Blindflange_status = 0 Then 'Bolting offComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kReferenceBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = FalseElse 'Bolting onComponent.InventorComponent("Bolting:1").BOMStructure = BOMStructureEnum.kDefaultBOMStructure 'Sets BOM Structure to Reference (Remove from BOM)Component.Visible("Bolting:1") = TrueEnd If
Is there a way to set all parts within a pattern BOM structure?
I made my bolting by adding 1 bolt, 1 washer & 1 nut and then pattern them using feature pattern select. Inventor 2013
I need to assign the dimension in my screenshot to a parameter so I can use it to drive another assembly. However, I can't find any way to capture it in a usable manner.
In the screenshot I have an associative part inserted that contains only a sketch with the projected line and point that I wish to measure between, but the geometry in the sketch does not update when the model geometry changes. This seems to be normal behavior?
I have assemblies that are comprised of reference parts - the assembly is a purchased part such as an air cylinder. I have them as reference only in the assembly (ie right click on the parts in the model tree->BOM Reference->Reference). I do it this way so I can adjust the air cylinder how I need it, but still only asign one part number to the whole assembly - as an example we'll say "cylinderX" is the part number, and filename is "cylinderX.iam"
The problem arises when I put cylinderX.iam into other assemblies and try and make drawings of those assemblies. Even though cylinderX.iam is not a reference part (but all it's sub components are), it shows up in an IDW just like reference parts. I am able to make it show up how I want by editing the view properties (Edit View->Model State Tab->Reference Data Line Style "as parts"), but I still cannot balloon cylinderX.iam. It shows up in the parts list, but I cannot attach a balloon to it.
Inventor 2013, 64-Bit
Dell Precision M6700
Windows 7 Pro
Intel Core i7-3820QM @ 2.70 GHz
16 GB Ram
NVIDIA Quadro K4000M
Space Navigator
I there a way of finding each Bom structured part that is set to reference in an assembly and setting the view of that component to in-visible.
Also needs to iterate into all set View reps that where created and set all views to not show the referenced parts as well.
Two different problems (questions). These are IV2012 files but the problems are the same in 2013.
Open the two attached ipt's. Launch the Measure Distance tool and measure between the blue an red face on the DimTest. It should read 1 inch.
Change to DimTest Derive using the tabs on the status line. Measure still gives 1 in. Change precision to All Decimals. The mouse pointer changes to calipers and the distance now measure 1.004 (which is correct)
Switch back to DimTest again using the tabs.
Measure again and notice the mouse pointer still shows the calipers which imply that it is going to return all decimals but the dimension given is still just 1 inch. Either the mouse pointer should change back or all decimals should stick.
OpenDimTest.dwg. Manage> Modify> Replace Model Reference and pick DimTestDerive.
ALL dims disappear and the origin indicator goes sick.
I am trying to replace a custom part - created from a content center part - with a copied part with a different name. (I am using the replace tool in an assembly.) However, Inventor is not replacing the part with the part I pick but rather the content center version of it.
View 3 Replies View RelatedOn the main sheet of my drawing I have the overall Parts List. Shows almost all parts except for the few that we don't want to list. On the second sheet I inserted a Parts List to show only parts that are shown in a detail on that page, made the rest non-visible.
On the main sheet there is an item (#13) that has a QTY of 3. Two of those Three are optional parts. What I'm trying to do is insert a custom part into the Parts List, give it an item number of 13A and put in the description "OPTIONAL", then do an Override in the balloon to show 13A.
I get it in the Parts List, Apply it, close it, save the drawing. Looking at the Parts List, item #13A is there, but item #14 is gone. I go back into the Parts List and 13A is there and there's a blue box around the item # and the description. I uncheck Static Value and number 14 shows up (item # and the description).
Then I go over to sheet two, open that Parts List and it lists 13A at the bottom with all the info I added in sheet one and it's non-visible. Go back to sheet one, open the Parts List and there is no 13A to be found.
I am working on an assembly that is designed around a box (bounding box) that could change size. I modeled the bounding box and placed it in a new assembly file. All other parts have been created within the assembly by referencing that bounding box with starting work plane and project geometry.
The problem comes in when I change the bounding box dimensions. The work planes for each additional part, which were defined by the faces of the bounding box, do not move when the sides move. Also, my projected geometry is not updating correctly. This is a simple box, with all 90° corners. So, all associated parts (at this point) are just rectangles.
My parts list on my idw do not update when I make changes to the model. Specifically, I have deleted a bolted connection on my design and replaced with a different components but the parts list table does not update - all I see is a lightning bolt in the browser next to the parts list but I cannot update it here.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
I was using virtual parts to add nuts and bolts to a drawing in 2013
I can make a VP bolt in the assembly, no problem, set it's size, weight, etc.
In the VP itself, there is no option for number of bolts I want it to emulate. For arguement's sake the weight was 1 pound per bolt (they are big bolts).
I can go into the BOM and say quantity 60, hit done and save the assembly.
If i open the drawing, the parts lists shows 60lbs for the 60 bolts total - which it should when summing the weight.
The problem is the BOM/assembly. If the weight of my assembly (without bolts) is 10,000lbs, the assembly sees the VP weighing 1lb and says the total weight is 10,001 lbs. Am i going to have to pattern a fake part to get this to work right? Shouldn't the total weight take into account the quantity set in the Bom??
Is there a way to display the density of materials that are assigned to varius parts in the parts list on a drawing? I don't need the mass of the parts I just need the material density to show up next to their respective parts.
For example, if I have a part with [steel mild] material assinged to it (no matter the size) I need a column in the BOM on the drawing to show: 490.684 lbs/ft^3. "Worry when there's something to worry about."
I have an assembly with a lot of purchased parts. I need to create a buy out list for purchasing. I've done this many times in the past and have a template set up for this purpose.
So now the problem, In this assembly, I have subassemblies showing up on my parts only parts list.
One of the subassemblies cinsists of two purchased parts. Both parts are set to purchased in the Bill of materials. If I do a parts only list on this assembly, it works as expected, showing two purchased parts. However, if I put that assembly into a higher level assembly, A parts only parts list shows the assembly instead of the individual parts.
IV 2010 Suite
Been working over an idw MANY times due to project lag.Today I opened it up and tried adding balloons to an already ballooned assembly.
The parts list has not changed, and is "structured".But, if I try adding balloons, they tag each part, not the entire assembly.
Also, I verified this by trying to add another parts list, which defaults to "parts only".
I can't show my data set, b/c it's HUGE, plus it's proprietary.
IV 2010 Suite
Digital Storm PC:
EVGA & Intel components
Win 7 Pro 64 bit
I have a .idw that I'm trying to make a parts list on. I select parts list and highlight everything. There are two screws that are not showing up on the parts list. I cannot select them manually either. It's acting like they are not there. Even if I do a complete parts list (adding the assemblies parts into one big list), they still don't show up.
How can I select these parts? What is wrong with them that they do not show up in the parts list?
I have been working with an assembly today where it is ideal to mirror parts and have figured out how to reuse the parts rather than create new parts. Now I find that when the parts are mirrored, they ate not retaining the mates. Where do I find the setting so they either retain their mates, or prefferably retain the mirror so that if I move the origional, the mirror moves as well?
View 9 Replies View RelatedI have structures and alignments data referenced. If I assign the structures ref alignments in the dwg with the data refs for labeling, the next time I open the dwg the ref alignments are set back to none, causing the labels to be ?
It seems like this worked in the past?
I'm working on a large infrastructure project with numerous of drawings. On quite a few layout drawings I need to have the same base set of references, however I need to change the layer settings (colors, lineweight etc.). This cannot be done in the base reference itself as it is used by others. As the layouts I work with includes other references as well, it is time consuming to filter and change layer settings on each base reference.
My concept is to have a master reference file to manage all layer settings and add/remove base references. When the master reference is referenced into the layout, all layer settings on the base references should stay as set in the master reference. In this way I can easily control all base references with one file and make sure all changes will be the same for all the layouts.
New illustration of concept:
I am getting this error in my production drawings.
My setup is as follows:
- EG.dwg has my existing surface in it. I create a data reference to use it in other drawings.
- Level One.dwg has the EG surface data referenced in, and I use this to create alignments, profiles, and finish surface. All of these are turned in to data references.
- Storm Sanitary.dwg has my pipe designs. I data reference in the two surfaces, profiles, and alignments, and create pipe networks. I create references for these networks.
- Plan Profile.dwg is the production sheet I'm getting this error from. Every one of my civil objects is data referenced in to this drawing. Everything is inserted correctly, the pipes show correct FG surface elevations for their rims, etc.
BUT when I open this drawing, I get this error. I assume it's because my FG surface is not directly in the storm sanitary.dwg.
How do I get rid of this error, without combining drawings, or promoting the surface to one or more drawings? Isn't this exactly what data references is made for?
know if we could put for example the Building of our Assembly in some 2D drawings as a "Reference" object and as a non reference object in other 2D drawings?
In some 2D drawings we don't need the whole building, and just with the references is enough, but in some other views, we need to see the building so we can represent the real obstacles we have or to show how the custumer should do the pipe implantation
I have Sample.ipt, SampleRev.ipt and Sample.idw. (Sample.ipt and SampleRev.ipt are the same configuration part with some different parameter value) Sample .idw is a drawing of Sample.ipt. How can I use code to change Sample.idw to be a drawing of SampleRev.ipt.
View 9 Replies View RelatedLet's say i want to draw a bike. In the 2D IDW of the wheel I want to see the frame as a reference. So, in the .iam of the wheel the frame subassembly is inserted and checked as reference. Also, a new level of detail is created that surpressed the frame.This level of detail is used in the overall assembly of the bike.
So, I end up with several subassembly's that contain other subassembly's just to reference them in the IDW. It would be better to have just one master assembly and create several IDW's from that assembly with different LOD and reference settings.
Inventor 2012 - 64 bit - build190 - Windows 7