Is it possible to isolate the interference detected by Inventor? I am thinking something trough the API or ilogic?
When we analyze interference we get a long list from inventor and sometimes is hard to see it. I am thinking maybe to Isolate the two parts that interfere.
how to change the color that the "Interference Analyze" tool identifies with??
I recently converted from 2010 to Inventor 2011 Pro. 2010 had a Dark Translucent Red which was extremely useful. 2011 has a Light Translucent Red which is extremely difficult to make out ( I have a massive assembly). Identifying these fouls/interferences is vital to my job.
I tried Styles Editor, View Styles, Application/Document Settings, and even part manipulation! (bah!)
how to change the color that the "Interference Analyze" tool identifies with??
I recently converted from 2010 to Inventor 2011 Pro. 2010 had a Dark Translucent Red which was extremely useful. 2011 has a Light Translucent Red which is extremely difficult to make out ( I have a massive assembly). Identifying these fouls/interferences is vital to my job.
I tried Styles Editor, View Styles, Application/Document Settings, and even part manipulation!
I cannot open anymore an IPT file (an error comes up). I know that the IPT file contains multiple references to other IAM´s and IPT´s via "Derived parts"; is there a tool to show all the references inside an IPT file?
View 9 Replies View RelatedBeing all new and complete virgin-like, to ilogic, I would like to know wether it is possible to analyze a sketch (wenn it is being closed)?
What I want to analyze is:
Does the sketch contain a fully constrained closed loop?
Does this closed loop consist only of straight lines?
What is the total number of lines in the loop?
Next fase is:
Create an excel-sheet with the following information:
For each line in this closed loop i wish to add the length of the line, and the angle to the next line (consequently on the internal side of the loop, resulting in angles from 0 to 180 degrees).
Is there a way to use interference checks to determine what material needs to be subtracted away from other parts to get the clearance needed? (See Attached) The way I typically handle this is to project the lines from one part onto the sketch of another and proceed accordingly, however as you can see, it didn't work out well in this instance as the face of the part in question is not parallel with the sketch plane in the other..Therefore making the cut location inaccurate.
View 2 Replies View RelatedI have a rack and a sprocket, in inventor, is there any command which can prevent the interference between both all the times.
my actual problem is while driving the motion constraints, sometimes, no pin of rack is in contact with sprocket, so i want to delete the motion constraints and want to rotate the sprocket to move rack, just as actualy it happens. Is t here any way to do so?
We just migrated from Inv 2011 where I had set the letter A as a shortcut for Zoom All. I tried setting it up again and ran into an issue where two commands were tied to it with the other command being Interference Analysis. I can't find interference analysis in the keyboard customization section and am wondering if there is a way to get rid of it's association with the letter A.
View 5 Replies View RelatedI am puttilng parts together on an assembly and right now when I move them they stop when they hit. how do I turn this off?
View 1 Replies View RelatedWhen I run an interference check on an assembly, any of the threaded holes that have fasteners in them shows interference. I guess that the problem arises from the document setting "Tapped Hole Diameter" is set to minor.
To solve the problem with the interference, I could either change the modeled size of the hole or change the modeled bolt diameter. Either one causes problems in other places.
I'm trying to figure a "fast" algorithm to obtain the amount of material (in linear distance) between 2 points within an assembly i.e. if I draw a line between any two points P1 & P2 in an assembly, what is the length of this segment that goes through material and what is the length that goes trough empty space?
For now I'm creating a thin cylinder as a new part, place it with one end at P1 and the other end at P2, calculate the interference volume of this body with the rest of the assembly and divide this number by the total volume of the cylinder. but has some problems:
1. It is VERY slow, and I want to call this function lots of times.
3. Is not accurate due to the finite diameter of the cylinder.
2. If the assembly has some interferences, the result is wrong (accounting same volume more than once)
I can't find how to change the color of the interference solid that is created during interference analysis. The default is red but unfortunately our housings are primed in red so I decided to color my housing assembly red without realizing that was going to make red highlights difficult to spot.
View 1 Replies View RelatedWhen you use Inventor command "Inspect" -->"Analyze Interference" command to analyze interference of two component, it not only gives you the interference volume, but also highlight the interference volume area to exactly identify it, as shown in the attached screen shot.
We want to implement this interference analyze using API. But the API sample (in AssemblyComponentDefinition.Analyze Interference Method) only gives the way to highlight the two interfering component occurrences and the interference volume, but there is no way to know where they exact interfere. So how to highlight the the interference location as in the inventor command? or does inventor exposes this function to API?
how can I close an iLogic Form from either an iLogic Rule, or a VBA Rule (VBA is the Preferred method)?
View 5 Replies View Relatedis possible to analyse the chain to see if is overlapping ?
View 9 Replies View RelatedI'm working on a drawing which requires me to rotate 3D rectangles until they are leaning against each other like dominos. Because they are standing on a curved path only one top corner of each will touch the adjacent rectangle, and because each one is shorter than the last the point at which they touch is different every time. There are over 40 rectangles.
I have no problem picking the correct axis of rotation for each but I want to avoid time-consuming calculations for the angle of each or the reference Point for each. Ideally I'd like AutoCAD to rotate until it recognizes that the solids are interfering.
Is there a command or a LISP for this?
I have run the interference check on pipes in my pipe network but I am not sure the results are accurate. I have set the 3D proximity distance to 1.7' in the attached example and Civil 3D found the pipes in interference with each other, but I'm not sure how this distance is calculated. This distance doesn't appear to be the pipe clearance measured along the perimeter (2.4' in green) or the inside diameter perimeter (1.8' in green) of my structure.
The distances measured directly between the pipes on the inside of the structure doesn't match the interference results either. I have set the pipe elevations and slopes to the same numbers in this example so I can measure the distance in 2D.
I have problem when i try to use function analyze mass model in revit building they show message like attached file.
View 1 Replies View RelatedI recorded video on a Black Magic Cinema Camera (BMCC), which has legendary video quality but an awful on-camera microphone with tinny recording process, and recorded audio on a Zoom H6 which has great low-noise, more bits and greater sampling rate capability.
In Premiere I made a Sequence containing the video footage, then added the H6 audio and synchronized it by waveform to the BMCC's audio, which I subsequently muted. I call this a Source-Sequence, as it is intended as a virtual source media item, to be cut into one or more Edit-Sequences (my term).
Not "holding my breath" but trying it anyway, in Premiere's Project/Bin pane, I selected that source-sequence then did RightClick > Analyze Content. Teasingly, that option was not greyed-out. However all options in the the resulting popup-dialog were greyed-out.
In this situation, to be useful, the speech analysis would need to be available to Sequences, not just to (Master) Clips. Obviously one could render such a sequence to intermediate but that would waste time and disk space and would essentially freeze the state of the Source (e.g. including any sync issues that might be discovered later, or whole-source color corrections issues etc.). If one subsequently altered that state, a re-render, re-link and re-analysis would be required. If a Souce-Sequence were used instead, and no alteration had been made to the audio (or if user indicated "don't care"), then there would in principle be no need for re-analysis.
In "Categories" of the filters window, it can be selected things which composes its mass, such as Mass Exterior Wall, Mass Glazing, Mass Roof. And these things can be clicked only after its mass become energy model.
I set up a filter rule of Mass Roof and applied it to V/G Filters of a view, but it did not displayed in Analyze Mass Model, the same as Mass Exterior Wall, Mass Glazing.
how to prevent EMF interference?
View 9 Replies View RelatedI have just put some photos together with transitions and a couple of music tracks. It is a n AV file as I wanted to put it back onto tape. Plays fine on the laptop but when I transfered it back to dv tape there was interference on the sound - difficult to explain the sound but like an intermittent spitting sound.
View 2 Replies View RelatedUnselected layers are creating parameters (or some sort of masking issue) on the selected layer. For an example. When I paint bucket a layer it will paint everything except.
View 4 Replies View RelatedI'm trying to use iLogic Design Copy to copy an assembly and all its associated parts to another directory. The assembly contains content center parts. Inventor warns me that the destination file of one of the CC parts (and 18 others) will be overwritten. When I go ahead and copy anyway, the copying process stops at that specific CC part. The Design Copy Progress dialog box states there is an error copying that CC part. When I close the Design Copy Progress dialog box, Inventor crashes.
The error copying the CC part: I'm allowed to use content center parts in iLogic Design Copied stuff, right? I searched some related topics and I'm under the impression that Inventor keeps the CC parts in its own directory and shouldn't be trying to overwrite them.
I want to give a poster I'm designing a look like it's been digitally compromised. This is one I like a lot, although I'm not seeking to render it unreadable like this one, perhaps toned down a slight bit.
View 5 Replies View RelatedAfter having made a record of my project, I see and hear a sound interference that looks like "click click click click click click". This often happens when rendering the transition constant gain.Here above render my project, the result and the problem.
And here below the photo of my project not encode, before rendering. occurred since the last update 2 Premiere Pro CC.
I am doing a tie rod the issue I have is when the length is between 2.001 and 2.250 we would drill thru all but only tap the ends .750 deep. If the part is 2.000 would would drill and tap thru in one step and not have to rotate the part in the lathe.
How do I get ilogic to understand if my number is between this 2.001 and 2.250 to lengthen the drill length parameter?Or add a mid plane cut? ( trying now code below reflects this try)
Not sure what way I want yet but I just can't seem to find a snippet or code to do this. I tried to add a list in the parameters for it to read but seems to do nothing.
If LENGTH <= "2" ThenFeature.IsActive("Thru_All") = TrueFeature.IsActive("Hole_A") = FalseFeature.IsActive("Hole_B") = FalseiProperties.Value("Project", "Description") = "RETURN ROLLER SHAFT, " & iProperties.Value("Custom", "DIAM") & " Ø S/S, TAP THRU 3/8-16, " & iProperties.Value("Custom", "LENGTH") & " LONG"ElseFeature.IsActive("Thru_All") = FalseFeature.IsActive("Hole_A") = TrueFeature.IsActive("Hole_B") = TrueiProperties.Value("Project", "Description") = "RETURN ROLLER SHAFT, " & iProperties.Value("Custom", "DIAM") & " Ø S/S, TAP BOTH ENDS 3/8-16, " & iProperties.Value("Custom", "LENGTH") & " LONG"End IfIf LENGTH = (My_List) ThenFeature.IsActive("Mid_Cut") = TrueElse Feature.IsActive("Mid_Cut") = FalseEnd If
Possible to run the 'import .xml structure' routine for an assembly BOM using either iLogic or VB?? I'm trying to replicate the Import button at the bottom of the BOM screen....
View 5 Replies View RelatedWhat I am trying to do is insert a part into an assembly file using iLogic. I basically want to mimic Inventor’s “Place” command using ilogic, maybe something like this:
oPath = ThisDoc.Path & ""
oFile = "File.ipt"
Component.Place(oPath & oFile, False)
This att. doc shows rule for exporting dxf out of drawing. It is working on one sheet just perfect. In multi sheets it save allways with same name. I want to choose from which sheet i need dxf but to be saved by sheet name or model properti name. Is that possible?
View 9 Replies View RelatedI have an external ilogic rule that creates a set of DWF drawings for all parts and subassemblies (as long as the idw files exist) within and including a main assembly.
I would like to merge all the DWF drawings of the sub assemblies and component parts into the DWF of the main assembly. Is there a method within DWFAddIn that will allow me to merge the files? Is there another way that I can merge the DWF files using the same ilogic rule (one rule to create and merge all DWF's together?)