When I run an interference check on an assembly, any of the threaded holes that have fasteners in them shows interference. I guess that the problem arises from the document setting "Tapped Hole Diameter" is set to minor.
To solve the problem with the interference, I could either change the modeled size of the hole or change the modeled bolt diameter. Either one causes problems in other places.
I want to put a threaded bolt in a threaded hole, until the bolt comes in contact with the bottom of the hole in .iam file.
View 5 Replies View RelatedIs there a way to tell Inventor to use the mean value for threaded holes? As it is IV always puts the Minor-min value for the hole size, which is a PITA for any and all CAM software.
The thread data can be extracted in CAM, but the hole size still remains what it's modeled as. I know I can edit the spreadsheet and cheat it, but that isn't exactly the correct way to go about it.
I just did a Circular Pattern of a threaded holes to a second solid body. The hole came through but the thread did not?Right now I have SP1 installed. I have been using solid bodies for a long time now and have not seen this.
A co-worker just came up with the same thing?
how to change the color that the "Interference Analyze" tool identifies with??
I recently converted from 2010 to Inventor 2011 Pro. 2010 had a Dark Translucent Red which was extremely useful. 2011 has a Light Translucent Red which is extremely difficult to make out ( I have a massive assembly). Identifying these fouls/interferences is vital to my job.
I tried Styles Editor, View Styles, Application/Document Settings, and even part manipulation! (bah!)
I've got a template with a set of Object defaults for an Inch drawing and a set for a Metric drawing. I've just noticed that within my metric set, if I insert a hole table with tapped holes, the font on the tapped holes doesn't match the other hole types. I'm searched around, but all the settings for the hole table style reference the same text style. (Please see the attached image.)
So is there a way to set a certain hole type to have a certain font or size within a hole table? Because if there is, I'd obviously like to remove it..... But I can't seem to figure out where the issue is.
I am trying to add a hole to an existing hole chart. I drop the part into a new drawing, set the ordinate "zero", and add a hole chart by selecting a few holes. When I attempt to edit the chart: click chart, right click "edit", click add hole, select new holes, right click to create, the "create" selection is greyed out and all I have to choose from is cancel. I searched the forum here but could not find a reference to this a know issue. Am I doing something wrong or is this a glitch of 2013.
We are running win7 x64 machines and this happens on both the 2013 Ultimate and Premium editions of the product.
I have had this problem intermittently for a few weeks since going to Inventor 2013 SP1.1. I have a part within an assembly and that part has holes created in it before assembling it with other parts. Now when I try and create a hole table in a drawing of the assembly I cannot select hole edges and the hole table is blank when trying to create it automatically from view selection. I originally thought it may be an alignment issue but I have since aligned everything correctly and it still persists. I can create the hole table if I import in just the part into the drawing but it will not allow me to create the table on the whole assembly.
I can also create the hole table if I use "centred pattern" and create cross hairs on all of the holes however it does not give me correct annotations for the holes as shown in attachment and I can manually change the annotations but seriously this should not be required. As shown in the screen shot it reads as A1 down to K1 instead of A1 to A10. .
Question: Is it possible to control the Hole Dimensions called out on the Hole Chart? As in controling leading/trailing zeros for main hole dim, alt home dim and tolerances? Can you combine the Main Dim with the Alt dim in a single column, separated with parentheses? (same with tolerance?)
View 5 Replies View RelatedI would like to use the hole command to place a hole in a part. When I place the hole it won't allow me to use one of the origin planes to locate the hole from. Can I only locate holes off edges?
View 4 Replies View RelatedI have an assembly that contains a part and a hole feature (the hole feature is at the assembly level). Using the api, I'm trying to get the hole location relative to the part's coordinate system in a without using the holeplacementdefinition.distance property, this way I can get the hole location regardless of the way it was defined.
View 2 Replies View Relatedi use hole feature names in hole table.
i assign hole names attribute to hole feature but dont get attribute hole table.
how to get hole names in hole table.
While creating holes in a part, a small counter shows (when you click on a point) of how many holes there are.
Programs:
Solidworks (1998-2011)
Autodesk Inventor (R8 - 2013)
Autodesk AutoCad 2D
Autodesk AutoCad 3D
Catia V5
SolidEdge
Anvil (Very old program!)
Pro/E
Our company works with some non-standard threads. I am making some 3-D models of our product and need to make a threaded bar.
View 8 Replies View RelatedI understand the process of splitting faces and applying a Bonded Contact between the split faces when you have a bolted connection with a nut, but what kind of contacts would you use for say a threaded connection?For example, suppose you have a plate that will be bolted to a mold. The plate has clearnace holes for said bolts and so that the bolts are threaded into the mold to be lifted. The plate has a threaded hole for the lifting mechanism (Swivel Hoist Ring). Finally, the desired load is applied to the Swivel Hoist Ring and the bolts are placed in pre-tension. I would like to simulate this via FEA but am getting tripped up in the contacts. Also I am trying to make it as simple and efficient as possible (by eliminating any bolts or other parts that are not needed). I use INV Pro 2014.
View 4 Replies View RelatedI have a part I am trying add a threaded hole to. The option for threaded holes is unselectable. I tried editing the registry as past posts have said, but the "parts" folder doesnt show up in the registry. I have been through every folder in the registry and dont see anything that has to do with threaded holes.
Running Inventor Pro 2012 on Windows XP.
Is it possible to isolate the interference detected by Inventor? I am thinking something trough the API or ilogic?
When we analyze interference we get a long list from inventor and sometimes is hard to see it. I am thinking maybe to Isolate the two parts that interfere.
Is there a way to use interference checks to determine what material needs to be subtracted away from other parts to get the clearance needed? (See Attached) The way I typically handle this is to project the lines from one part onto the sketch of another and proceed accordingly, however as you can see, it didn't work out well in this instance as the face of the part in question is not parallel with the sketch plane in the other..Therefore making the cut location inaccurate.
View 2 Replies View RelatedI have a rack and a sprocket, in inventor, is there any command which can prevent the interference between both all the times.
my actual problem is while driving the motion constraints, sometimes, no pin of rack is in contact with sprocket, so i want to delete the motion constraints and want to rotate the sprocket to move rack, just as actualy it happens. Is t here any way to do so?
We just migrated from Inv 2011 where I had set the letter A as a shortcut for Zoom All. I tried setting it up again and ran into an issue where two commands were tied to it with the other command being Interference Analysis. I can't find interference analysis in the keyboard customization section and am wondering if there is a way to get rid of it's association with the letter A.
View 5 Replies View RelatedI am puttilng parts together on an assembly and right now when I move them they stop when they hit. how do I turn this off?
View 1 Replies View RelatedWe want to use dual dimensions for holes and figured out how to do this by editing the styles. This works great except for threaded holes the dual dimension is redundant as shown in the picture.
Is there a way to not have the dual dimension for threaded holes but keep them for other holes? Having a dual dimentsion for a metric thread or having it printed twice on the drawing is pointless.
INV 2013
how to make this Clamp Rod to Clamp Base Spacer Turn relationship.
this is from the Clamp Project on this site: Inventor Wizard, The Clamp Lever is turning or rotating the clamp rod into the Clamp Base Spacer but I could not simulate the Thread or the Screw motion if that is the term, or the 1 or 1/2 turn of the Clamp Rod to 1 Pitch movement, plus I can't seem to put the Rod inside the Clamp Base Spacer hole when the Contact Solver is ON, maybe modeling issue on my part.
I'm trying to figure a "fast" algorithm to obtain the amount of material (in linear distance) between 2 points within an assembly i.e. if I draw a line between any two points P1 & P2 in an assembly, what is the length of this segment that goes through material and what is the length that goes trough empty space?
For now I'm creating a thin cylinder as a new part, place it with one end at P1 and the other end at P2, calculate the interference volume of this body with the rest of the assembly and divide this number by the total volume of the cylinder. but has some problems:
1. It is VERY slow, and I want to call this function lots of times.
3. Is not accurate due to the finite diameter of the cylinder.
2. If the assembly has some interferences, the result is wrong (accounting same volume more than once)
I can't find how to change the color of the interference solid that is created during interference analysis. The default is red but unfortunately our housings are primed in red so I decided to color my housing assembly red without realizing that was going to make red highlights difficult to spot.
View 1 Replies View RelatedHere is the issue we have found. While sectioning a view of an assembly in idw, the threaded lines of threaded features have a strange behavior depending on the section line used. I have attached a simple example that shows what he have found. Basically, if the section line is straight, threaded features show correctely. Independent of section participation. If the section has segments at different angles, then lines are not appearing.
The first three views have both parts excluded from section participation(Obviously, there isn't any real life need for this, but I did it to just simplify the illustration without adding a bunch extra parts) The base view is the top view or view showing the round shape. For the first example at the bottom, i simply projected the view to the left and made sure "Threaded Features" was selected. Threaded lines show fine.
Second example is the similiar, except the i used a section view instead of the projected view. Both parts are excluded. Section line is straight. Verticle in this example. Doesn't have to vertical as the line is straight.
Next example is similiar to the second, only difference is the section is not straight. You can see the threaded lines do not show. This is the problem we want to solve. How to make the threaded lines display!!!
Last example shows the same section, only this time the component is included in the section participation. And it works.
Any settings to change or a trick to make it work. Otherwise, i think i need to issue a support request with autodesk.
In most cases threaded parts are designed without true surface (just cylinder with texture) thus part surface area is calculated wrong (less than it is i real world)).
any automatic way to get true value of threaded surface which is modeled in traditional (simplified) way?
When you use Inventor command "Inspect" -->"Analyze Interference" command to analyze interference of two component, it not only gives you the interference volume, but also highlight the interference volume area to exactly identify it, as shown in the attached screen shot.
We want to implement this interference analyze using API. But the API sample (in AssemblyComponentDefinition.Analyze Interference Method) only gives the way to highlight the two interfering component occurrences and the interference volume, but there is no way to know where they exact interfere. So how to highlight the the interference location as in the inventor command? or does inventor exposes this function to API?
how to change the color that the "Interference Analyze" tool identifies with??
I recently converted from 2010 to Inventor 2011 Pro. 2010 had a Dark Translucent Red which was extremely useful. 2011 has a Light Translucent Red which is extremely difficult to make out ( I have a massive assembly). Identifying these fouls/interferences is vital to my job.
I tried Styles Editor, View Styles, Application/Document Settings, and even part manipulation!
Is there a way in the description field of an Inventor hole table to have mixed units? Some hole sizes at fractions, some at 2 plc, and others at 3 places.
Inventor Pro 2013 or 14
I'm searching for blocks of all types and sizes of threaded pipe fittings.
View 5 Replies View Related