AutoCAD Inventor :: How To Make Surface From Equation
Nov 26, 2013
I need to make a model of saddle surface. The surface is given by equation z = y^2 - x^2, and I must have some thickness - It will be printed on 3D printer.
I have Inventor 2014 and I dont see possibility of making the surface directly in Inventor. Is there any trick for that?
I'm afraid I cannot use solution as stated here Equation-driven surface , because saddle surface looks like this hyperbolic paraboloid .
I tried this solution: I made 3D surface in Matlab, exported it in .stl and opened in Inventor - but this only makes the surface with no thickness. Functions extrude, loft require 2D sketch.
2. What is the minimum dimension to make my part appear?
On the drawing I was working on, the part completly behind a surface was showing up until I rotated the view, then it dissapeared, this behaviour is not present in the test idw, the part doesnt appear at all behind the surface.
I'm trying to make a surface cut on my part. The part is a round cylindrical shaped cap with a surface geometry going through the center. I want to make that surface geometry remove some of the cylindrical part by about half the wall thickness.
See the attachment of the picture "cap" for a picture with the surfaces I'm speaking about. The orange features are surfaces and the grey feature is just a solid cylinder that I want to cut. The vertical, cylindrical surface in orange is where I want the grey cylinder to be cut along the curved orange surface. Only on the grey area outside of the orange cylindrical surface is to be cut while leaving everything grey on the inside area of the cylindrical surface will remain.
The picture titled "ideal cap" is the look that I'm going for on the picture titled "cap" which I'm trying to perform this cut on. The picture titled "ideal cap" was made using Pro/E and I'm trying to mimic the same thing in Inventor. How I can do this?
I have the German version of Inventor 2014, so some translations may be different.
I want to project a text on a sketch onto a conical surface. The error message is that the chosen surface wasn't tangential to the profile plane. I found no way to rotate the plane.
How do I project my profile onto the conical surface or How do I make the profile plane tangential to the conical surface?
Can an equation be used to calculate equal distances when using the rectangular pattern.Regarding the attached .ipt file i would like to place 25 holes in the X direction with equal gap size between each hole.Also how to calculate the number of holes in the Y direction again with equal distance between each hole.I have not done this before with equations but was thinking that i would need to use the Length x Width in the equation.Do i need to add figures into the Parameters box also?
The attached file with the Hole feature the sketch is not constrained for the purpose of using an equation so i know how far from the start of the part to get equal distances between each hole to the end of the part .
We have some equations in our templates which i have modified with iLogic. Once the rule is run it only shows the value and not the equation. ie i want it to show Thickness*2 instead of just '12'. The ilogic will say something like InnerRad = Thickness * 2 Is there a way to make it show the equation rather than the value? While i know whats going and can see the driven link in the parameters the planned change to 2012 could take some getting used to for users.
I was trying to use ipart to create some parts and place the relevant dimensions in the table format in the idw file. However, the equation for the dimensions appeared and I like to have it as numeric. Also, the feature present or absent is preferred to be called "Yes" and "No" instead of "Computed" and "Suppress" respectively.
If you look in the attached PDF, I have an elliptical wall that also has changes in elevation. call it a compound radius if you will. What I have to do is to make a wall cap to go on top of the wall. I know, sounds fun.....I have the surface on the right of the PDF and i need to figure out how i can take that shape and have it lay flat so that i can cut this shape out on my CNC. i know I can use the FLATSHOT command, but this will not give me the true shape of the board.
I have an asssembly stack and I have a known bending moment at a given place (ie the datum). I want then to create a drawing of this stack up and show the bending moments at known locations beside the relative dimension.
Now I can do this manually no problem...but I would like this drawing to update automatically. ie the stack up height(s) change and i want the bending moment figure to update accordingly.l
Is there a way to do this with drawing dimensions? ie dimensions created in drawing mode?
I'm trying to use the equation curve to draw a super ellipse.The formula I'm trying to translate for inventor is the following.I'm guessing this should be possible using the abs() for the first section and an IF() statement for the second. The problem is Iäm not even getting the abs() to work at all. How to translate this formula?
I have a small assembly with the parts. I'm doing an array (pattern) of one of the parts and I tried to do two things without success:
1. Tried to link one of the parts to the assembly itself with the equation tool ,but the software doesn't let me do it and says "...was rejected since it causes a cyclic dependency" - so what?:-) I know and need to do it!
2. After rejected the first choice, I tried to "project geometry" some stuff of the pattern I created in order to try and and make my connection in this way, but then I got a similar rejection: : problem encountered when doing cross part projection"...probably it's because it's from a pattern I'm creating from the part I'm doing this sketch inside?
What Can I do in order to bypass these remarks and make it somehow? Most important, Why can't one "tie" something from a part to its own assembly in which it's located???
Is there any way in which the text of a text parameter, which is in the equation column, can be replicated into the nominal value column in the parameters table? I want to reference the value of the parameter in Custom iProperties but it always comes up as blank because it has no value.
I need it to update automatically, e.g not entering the value manually.
what the 2D or 3D equation curve for a parabolic spiral, otherwise known as a Fermat's spiral would be? I have found this info but do not know how to apply it:
Fermat equation
Therefore in terms of the affine plane its equation is The Fermat curve is non-singular and has genus
I am trying to create a coil which from above, retains equal and thus parallel pitches whilst at the same time adheres to a semi-circular form in the cross section. You can see from the images attached that the first two revolutions are larger than the semi-circle outline.
These are the values I have used:
Cylindrical
r (t): 134.56924424045517662353735770102mm * t * 0.5 q(t): 1 deg * 360 ul * 3.0 ul * t z(t): 10 mm * 6 ul * 0.5 ul * t * (1.5 * t) * t
When you sweep a profile along a helical path, use the plane normal sweep (instead of perpendicular sweep) to orient profiles suitable for coil or spring. In the example below, the sweep path is a constant radius, variable pitch helix.
I would like to create an equation driven curve with inventor. I have no problems plotting the function in a plotter, however, inventor won't accept my equation. It gives me the error message, saying: "The equation contains unit errors". I'm using the explicit equations.That's the bare equation:
But both equations are not accepted by inventor due to unit errors. In this design, I'm using the metric system, millimeters, so I don't understand why and how I have to redefine this for the equation in order to get it working.
Is there a way to graph a curve using an equation over a closed interval in Inventor 2012? I know I can draw a spline through points that are solutions of my equation, but this does not guarantee that the curve is the graph of my equation.
I have an iPart that I have created parameters to perform some basic calcs so the values will show up on every member. The parameters are correct for the different member so it appears to be working correctly on the model side. For example I have a parameter called 'CutLength' that performs simple math functions. But when I make the table on the drawing and I include this parameter, I see the formula in the table instead of the value. Is there a way I can have it display the value instead of the equation?
I'm modeling a temperature gauge and would like to have glass over the gauge so the inside is visible. I can easily do this with an assembly, but I'm wanting to do this with a single part. I tried to derive a new part from the assembly, but the transparent part turns solid so nothing inside is visible. Is it possible to do this?
I've include pictures of what I want and what I end up with.
Inventor Professional 2013 Intel Xeon W3680 @ 3.33Ghz 12GB DDR3 RAM NVIDIA Quadro 2000 GPU Windows 7 Professinal 64-bit
how I can add more volume to curved object surface? Say for example I have a plastic cup.You can think of this as cylinder object ,which was the shelled out using the shell tool and then had its base sealed.
Now at certain parts, I would like to increase the thickness and then blend it the rest of the surface(may be chamfer its edges) .
At certain parts on curved surface I would like to add an extra mm, I think if the surface was flat I would just sketch the shape, then extrude it by few mm and smooth the edges by doing a chamfer
But how can this be done on surface that is curved? Or multi curved for edges?
I'm designing a press for a skateboard similar to: Rib Press
I have the board modeled: (see attached)
Now what i want to do is generate those ribs as seen in the picture.
I tried creating a block that intersected with the board and tried to split the rib at the surface, but to no avail. I think the issue has something to do with the curve of the board in two directions, but i can't seem to get it right.
if you are having trouble visualizing what i'm asking about, look at this. I want to be able to figure out the exact shape of those center ribs to print and eventually cut out of wood.
