I'm just starting out with learning equation curves in Inventor.How can I get this curve
r(t)= ti + 4cos tj +9sin tk; where t is greater than or equal to 0
how to get this VBA as an equation curve
I am trying to create a coil which from above, retains equal and thus parallel pitches whilst at the same time adheres to a semi-circular form in the cross section. You can see from the images attached that the first two revolutions are larger than the semi-circle outline.
These are the values I have used:
Cylindrical
r (t): 134.56924424045517662353735770102mm * t * 0.5
q(t): 1 deg * 360 ul * 3.0 ul * t
z(t): 10 mm * 6 ul * 0.5 ul * t * (1.5 * t) * t
tmin: 0 ul
tmax: 0.916 ul
I want to draw hyperbola curve whose equation is x^2/a^2 - y^2/b^2=1. May I use equation curve tool to make the above hyperbola.
I have also made a hyperbola curve of aforesaid equation through conventional method on mathematical ground in the past.
I'm trying to use the equation curve to draw a super ellipse.The formula I'm trying to translate for inventor is the following.I'm guessing this should be possible using the abs() for the first section and an IF() statement for the second. The problem is Iäm not even getting the abs() to work at all. How to translate this formula?
View 1 Replies View RelatedTrying to do something as simple as y=x^3 (Explicit Mode). Set xmin = 10, xmax = 20 then tried y(x) = :
1in *(x^3) -- no good
(x^3)/1 in -- no good
(x/1 in)^3 -- no good
Error is that "Equation y(x) contains errors. Expected units are length".
The point here is: Why should typing in such a simple equation as y=x^3 be so difficult??? Can't even do (x*x*x)/1 in & make it work.
Can i make an Equation Curve such that it is dependent on a parameter from my Parameters list?
View 1 Replies View RelatedWhat are the parameters for a parametric 3D Equation Curve to create a path for a coil similar to that in the attached image?
Or alternatively tell me how I can produce the coil in some other way!
what the 2D or 3D equation curve for a parabolic spiral, otherwise known as a Fermat's spiral would be? I have found this info but do not know how to apply it:
Fermat equation
Therefore in terms of the affine plane its equation is
The Fermat curve is non-singular and has genus
I have also found this: $r^{2}=a^{2} heta $
Please see image attached.
You can create a variable pitch helix by using the Equation Curve feature introduced in Inventor 2013.
Create a new 3D Sketch. Start the Equation Curve command.
Here are equations that I use to create helical curves. Many other variations exist.
Cartesian coordinates:
x(t) = radius * sin(360 * num_turns * t)
y(t) = radius * cos(360 * num_turns * t)
z(t) = height * t
[Code]....
When you sweep a profile along a helical path, use the plane normal sweep (instead of perpendicular sweep) to orient profiles suitable for coil or spring. In the example below, the sweep path is a constant radius, variable pitch helix.
I would like to create an equation driven curve with inventor. I have no problems plotting the function in a plotter, however, inventor won't accept my equation. It gives me the error message, saying: "The equation contains unit errors". I'm using the explicit equations.That's the bare equation:
"y=sqr(2)*16.5/2/sqr(pi)*sqr(arccos(1-2*x/50)-(sin(2*arccos(1-2*x/50))/2))"
I modified it, inserting variables which I defined also in inventor, leading to this:
"sqrt(2)*height/2/sqrt(PI)*sqrt(acos(1-2*t/length)-sin(2*acos(1-2*t/length))/2))"
But both equations are not accepted by inventor due to unit errors. In this design, I'm using the metric system, millimeters, so I don't understand why and how I have to redefine this for the equation in order to get it working.
Is there a way to graph a curve using an equation over a closed interval in Inventor 2012? I know I can draw a spline through points that are solutions of my equation, but this does not guarantee that the curve is the graph of my equation.
View 2 Replies View Relatedcreate an ellipsoid with a hyperbolic funnel on the end.
How can I join an equation curve to an ellipse to create revolved ellipsoid shape? I also have alias and fusion if these are needed.
Can I create a specific curve in latest released version of AutoCAD by an equation?
If yes, what version of AutoCAD is it, and also how to enter the equation?
Much of our work is structures fabricated from steel plate. One of our practices is to add a note " (SK) " to the description of plates that have a detailed sketch somewhere in the fab drawing set (simple rectangular or circular plates with no additional features do not get these detailed sketches). The actual "detailed sketch" is just a dimensioned drawing view of that plate.
I've been working on automating this process so that Inventor can actually determine for the user whether or not the sketch is required. I have it in certain part templates by default. Other templates add the note automatically through iLogic when certain plate features are selected, or when the model consists of multiple part features.
This leaves one remaining case that the current set of rules can't catch - when the user creates cutouts, notches, etc. by modifying the sketch for the original extrusion. I have determined a method for catching that case, but haven't yet figured out how to program it.
What I want to do is count all of the lines, arcs, and circles in the first model sketch. If that count returns a number other than 4 lines, the note will be added. If any arcs are detected, the note will be added. If any circles are detected with lines also present, the note will be added. There may be other cases that will come up in testing that need to be covered, but I ran into an issue before I got that far. Construction geometry messes up the count - I need a way to exclude it.
Below is the test code I have so far for the counter. what techniques I can use to get construction geometry out of the count. This code doesn't include the provisions for actually adding the note yet - I'm just trying to get the counter working right first. Instead it's just displaying the total count in a message box for test purposes.
oDoc=ThisDoc.Document
oSketch=oDoc.ComponentDefinition.Sketches.Item(1)
LineCount=oSketch.Sketchlines.count
CircleCount=oSketch.SketchCircles.count
ArcCount=oSketch.SketchArcs.count
TotalCount=LineCount+CircleCount+ArcCount
MessageBox.Show("Total Count "&TotalCount, "Title")
I'm building a product configuration which includes some helical curves. I want to find out how I can change the direction of a Helical curve feature in a 3D sketch.
Variables like pitch and diameter are parameters, but the direction isn't.
I made a bunch of lines, then used the bend command to make curves where they intersected. I'm trying to put lines connecting A to C and B to D. How do I constrain the ends of the lines to the center of the curves?
View 9 Replies View RelatedI would like to use a sketch as the basis for a rectangular pattern which is set up to use the curve length for both directions of the rectangular pattern so that when I update my rectangle in a sketch, the pattern automatically adjusts to the new sketch. I have sketched a rectangle, and used one leg of the rectangle to establish the direction and length of one dimension of the array.
However, when I try and choose the Direction 2, my only options are the entire rectangle or faces- I can no longer select other and choose a single side of the rectangle.
I was able to accomplish what I wanted by using two sketches, with the second sketch simply projecting one leg from the first sketch. Using one sketch just seems inherently safer than trusting projected geometry.Is there a way to accomplish this with one sketch instead?
Inventor 2013 (SP2 Update 2), Windows 7 Professional (64-bit), SP1, Intel Xeon 3.07GHz CPU, 12GB RAM, NVIDIA Quadro 2000, Vault Basic 2013
I am trying to create a 3D sketch of a helical curve that has an accelerated pitch.
View 2 Replies View RelatedI am trying to write a script to draw geometric figures in Illustrator.I want to achieve this by writing an equation into the ESTK, for example x^2 + y^2 =100. This should generate a circle with a radius of 10 units.
View 1 Replies View RelatedI need to make a model of saddle surface. The surface is given by equation z = y^2 - x^2, and I must have some thickness - It will be printed on 3D printer.
I have Inventor 2014 and I dont see possibility of making the surface directly in Inventor. Is there any trick for that?
I'm afraid I cannot use solution as stated here Equation-driven surface , because saddle surface looks like this hyperbolic paraboloid .
I tried this solution: I made 3D surface in Matlab, exported it in .stl and opened in Inventor - but this only makes the surface with no thickness. Functions extrude, loft require 2D sketch.
Can an equation be used to calculate equal distances when using the rectangular pattern.Regarding the attached .ipt file i would like to place 25 holes in the X direction with equal gap size between each hole.Also how to calculate the number of holes in the Y direction again with equal distance between each hole.I have not done this before with equations but was thinking that i would need to use the Length x Width in the equation.Do i need to add figures into the Parameters box also?
The attached file with the Hole feature the sketch is not constrained for the purpose of using an equation so i know how far from the start of the part to get equal distances between each hole to the end of the part .
I need to put the following into equation form to plug into a User Parameter:
if d91 falls in the range of 4" to 11"
then d92 = d91 + 2"
else d92 = 7.5"
Windows 7 Pro, SP1
Inventor 2012 SP1
Due to the nature of our business, I am not permitted to attach any files showing models or .idw environments of any actual work-related components.
how can i access the value in this column using vba?
View 1 Replies View RelatedI need to put in the polar equation r=e^theta. Is this even possible in autodesk? How can I do it? Should I spline through points instead?
View 4 Replies View RelatedWe have some equations in our templates which i have modified with iLogic. Once the rule is run it only shows the value and not the equation. ie i want it to show Thickness*2 instead of just '12'. The ilogic will say something like InnerRad = Thickness * 2 Is there a way to make it show the equation rather than the value? While i know whats going and can see the driven link in the parameters the planned change to 2012 could take some getting used to for users.
View 9 Replies View RelatedI was trying to use ipart to create some parts and place the relevant dimensions in the table format in the idw file. However, the equation for the dimensions appeared and I like to have it as numeric. Also, the feature present or absent is preferred to be called "Yes" and "No" instead of "Computed" and "Suppress" respectively.
View 1 Replies View RelatedI have an asssembly stack and I have a known bending moment at a given place (ie the datum). I want then to create a drawing of this stack up and show the bending moments at known locations beside the relative dimension.
Now I can do this manually no problem...but I would like this drawing to update automatically. ie the stack up height(s) change and i want the bending moment figure to update accordingly.l
Is there a way to do this with drawing dimensions? ie dimensions created in drawing mode?
I have a small assembly with the parts. I'm doing an array (pattern) of one of the parts and I tried to do two things without success:
1. Tried to link one of the parts to the assembly itself with the equation tool ,but the software doesn't let me do it and says "...was rejected since it causes a cyclic dependency" - so what?:-) I know and need to do it!
2. After rejected the first choice, I tried to "project geometry" some stuff of the pattern I created in order to try and and make my connection in this way, but then I got a similar rejection: : problem encountered when doing cross part projection"...probably it's because it's from a pattern I'm creating from the part I'm doing this sketch inside?
What Can I do in order to bypass these remarks and make it somehow? Most important, Why can't one "tie" something from a part to its own assembly in which it's located???
Inventor 2012 Pro.
I7 workstation
Is there any way in which the text of a text parameter, which is in the equation column, can be replicated into the nominal value column in the parameters table? I want to reference the value of the parameter in Custom iProperties but it always comes up as blank because it has no value.
I need it to update automatically, e.g not entering the value manually.
I've created a shared sketch and have used it with various features. Sometime those features are suppressed. The model works fine but the shared sketch generates a sketch doctor error because the feature that created it has been suppressed. Is there anyway to make the sketch suppressed so it doesn't trigger a sketch doctor error? Inventor 2013
View 2 Replies View RelatedI am almost sure this is not possible in AI but I will ask it anyway:
is it possible to assign value of parameter as a result of non linear equation?
for example I would need parameter x to meet the equation
cos^2x+Ax+C=0
where A and C can be other fixed parameters.
