Is it possible to search & find where a dimension listed in the parameters dialog occurs in a part model ( in which sketch for example)?
Inventor Suite 2013 Ultimate
if it is possible to increase the number of recently used values/parameters in the dimension dialog, during part sketching. For one part, I use approximately ten parameters that will be used repeatedly. When I'm done with one sketch and start with the next, only the last five parameters are in the recently used parameter list. (Create dimension --> select arrow on right side of dialog, see attachment Dimension_Dialog.jpg, excuse me for the poor quality ). It would be much more comfort to have more parameters in this 'recently used'-list.
Furthermore I'd like to know if it's possible to widen the parameter-list. In my case I've several parameters that start with the same prefix, followed by a differentiating suffix. When I create a new dimension, select the arrow on the right and select 'List Parameters', I have to adjust the width of this dialog every time to see the entire parameter. (see picture Dimension_parameters.jpg)
Why does this message appear? Is there a setting that is turned "on" that should be swtiched "off"?It occurs under Editing Dimension and Parameters.
View 1 Replies View RelatedI have an assembly with 10 parts in it. We use many assembly features at the assembly level (Revolve cut, Extrusion cut..etc). How to find the mass difference of each part by comparing at its parts level and its assembly level.
View 1 Replies View RelatedIf I want to find part which is inside another part or assembly, which means no matter how I turn camera, I always cannot see that part.
Does inventor has this function? Or is it possible to develope by .NET API?
I tried to match the dimensions of the already existing product with new dimension through fx parameters(using link excel sheet), while conversion all the dimensions are changed except taper value (By default it comes with inch instead of degrees) It can be changed by adding user parameter but i want it to consider from excel sheet data itself. Is it possible? For reference i have attached the snap shots
View 1 Replies View RelatedThe drop down arrow and check mark have disappeared from my Edit Dimension Dialog Box. What are the setting to turn those back on?
View 4 Replies View RelatedI need to use parameters of a part in an assembly. How to do this? Do i need to define a rule? How is this done?
Can i do it without using an Excel sheet as a parameter source for both the assembly and the part? The target is to have inventor update an array of assets as soon as the width of a part is changed whether in Excel or in the Factory properties of the asset.
I'm new to Inventor. Lets say I create a part called Pipe.ipt. In it I specify the OD, Thk and Length of the pipe. If I then create an Assembly, and I want to use multiple instances of Pipe.ipt, but each instance has a different set of parameters (i.e. different OD, Thk and Length). How do I do this?
I see I can set up iPart, and I could set up tables with the OD and Thickness for various standard pipe sizes. But this doesn't address the length. How do I re-use the same Part in an assembly, but each part has it's own set of unique paramenters?
I have a part made where various parameters in it.
Now I place the part in a assy and from there i want the parameters to control the part.
I do this now by the same parameters from the part to add in the assy by typing the parameters manually in the assy.
Is there a way that you can define parameters retrieved from the part about the assy without retyping and therefore can make mistakes?
how to dump the counter of parameters of model:
d0, d1, d10, d12
became
d0, d1, d2, d3
How we can access the part parameters after hitting create iAssembly. do I need to make i parts first and then bring them to an assembly and make an iAssembly??
View 5 Replies View RelatedI have design tree like this:
Main Assembly
L Sub Assembly1
L Sub Assembly 2
L Sub Assembly 3
L part 1
in part i have a parameter name ("Panjang")... how to control "Panjang"?. I cannot access a part parameter in Sub-assembly.
[URL]
I am trying to control the parameters contained in a part that is not in my assembly. May sound odd, but I am using the multi body part modeling feature to create all of my bodies in a single part file, then making these components/sub assemblies, and pulling them into my assembly. However, I do not want to have the "control part" in my assembly, I just want it to drive the parts. I cannot figure out how to access these parameters without having the part included in the assembly...
View 7 Replies View RelatedI have the following problem. I design a simple part - an extruded base, so i have a parameter in this part that i can control the extrusion distance - i call this parameter D.
Then i create an assembly and place the part in it. How can i access the parameter D of the part from within the assembly?
I want to place multiple instances of this part in my assembly and control each parameter D of an instance using an excel worksheet that is linked with the assembly. How can i do it ?
My aim is to design a very simple manipulator. Each link has the same shape but a different length. I want to control each length from an excel worksheet and not from an ipart table. I want to have only one worksheet that controls the parameters of my assembly such as constraint angles , and link lengths.
I have a configurator assembly, which is controlled with an iLogic rule.
one of the parts is being changed in a lot of ways according to the different configurations. But in one of the Configurations the part must be suppressed, which works fine, however next time i run the rule i get an error message from all the other instances where it would change a parameter if the part was active.
I have tried adding if [the configuration that makes the part suppressed] = False then, in the beginning of the the code that fails, to simply prevent it from running, but it still makes an error.
and as you can see i have a lot of lines where the part normally would be configurated.
Error on Line 628 : Method arguments must be enclosed in parentheses.
Error on Line 629 : Method arguments must be enclosed in parentheses.
Error on Line 633 : Method arguments must be enclosed in parentheses.
Error on Line 634 : Method arguments must be enclosed in parentheses.
[code]........
I don't understand how to enclose the argument in parentheses.
In the recent past I've been putting textboxes (General Notes) on drawings, and using part-parameters in these textboxes to display the values stored in these parameters (see attached picture). Is there a way to automatically put a link to these parameters into the notes through the API / VBA so that these values update when the part changes? With the property obj_GeneralNote.Text it's only possible to add plain text.
Product Design Suite 2014
Inventor 2014, Vault 2014
HP Workstation Z220
Intel Xeon 3.4GHz
16GB RAM
Nvidia Quadro 4000
Windows 7 Professional (64bit)
I have 2 parameters in a part (a spring), "diameter" and "Length".
I change these parameters with iLogic to build several springs.
Is it possible to update the "Part Number" Each time I change the parameters "diameter" and "length"?
I want to get the following:
Mola_Ø-65_L-140
Where 65 is the parameter value and 140 is the length value.
I tried with the code below,
iProperties.Value ("Project", "Part Number") = "Spring_Ø-" Diameter "_L-" Length
but that returns: End of statement expected.
Autodesk Factory Design Suite Ultimate 2014
Autodesk Simulation Mechanical
Autodesk Simulation CFD
Windows 7
I created a basic part using Inventor and some how something created some parameters out of the blue. I know that I didn't create the parameters. The parameters got created automatically some how and I would like to know how this happened so I can do it again, because it would save a lot of time.
Here are some of the parameters that got created.
vParam_Title
vParam_Project
vParam_Description
I have included the file that this issue occurs in.
I am working in one assembly. in that assembly i created all the part with using i part & same part i called in to the assembly & created i assembly. while creating drawing i have facing problem to show the model parameters in to the assembly drawing table. How to link the model parameters in assembly parameters with using i assembly.
View 1 Replies View RelatedIf I double click a workplane in the browser, the edit dimension dialog comes up half way off screen, does not remember the screen position if I move it, so it has to be repositioned every time. Seems to be tied to the browser position.
View 9 Replies View RelatedMy goal is to open have people go into a central assembly file, type in their specific parameters and the various part files update within the assembly. I wish to do this without the need for an excel sheet, but when I try to link the parameters from the assembly file to the part files, it will not allow me to insert these parts. I get an error about an "assembly can not be placed into itself."
Iparts will not work as this has an infinite amount of sizes.
I made an assembly that adjusted to sized based on some key parameters. These key parameters are controlled by a form in the main assembly. The keys parameters actually adjust the skeleton file, which then drives the frame, then all the parts are adjusted.
after changing these parameters all necessary parts would adjust to size and keep the location constraints. Worked quite well.
The issue now is that, we adopted a new naming convention and this assembly requires all the part files to be renamed. I meticulously saved each part as their new name and then replaced each component in the main assembly. This worked to an extent. The problem that I am facing is that when I saved each part as there new name, the new part retained the linked parameters to the old part. Is there a way to change this link to the newly name skeleton file?
I looked into design assistant for this process as well, but the only changes I think available were to add a prefix or suffix. If worse comes to worse, I can remodel this project but, I am sure there has to be a way to alter this.
attached is a single part with those parameters in the image above.
Is there a standard command or command sequence that allows for the changing of a parameter, say length, of a component from within an assembly. I'm looking to compile a code that allows for a template to be created, then that template will do changes based on text box input and then save out the modified parts with new part numbers.
View 2 Replies View RelatedI have some parts with varies User Parameters that allow cusomization of part features. With numeric user paremeters we can check the export parameter box and then, in the description of the part we can refrence that parameter. For instance the description could be: =Width <Width>, Height <Height>, etc. Where it would desplay as Discription: width 22in, height 12".
We also have text User parameters. Is there a way to add these parameters to the description as well? They do not have the option of checking the export parameter box in the parameters table.
I would like to have a rule that will add specific user parameters to a part file. These parameters need to be formatted so the width, depth and thickness will control the description of the part.
IE:
Width=4
Depth=2
Thickness=3/16
DESCRIPTION = TS <Width>X<Depth>X<Thickness>
I would like to format each parameter so that the:
Format=Fractional
Precision=1/16
Unit string=False
This is what I have so far:
oMyParameter=ThisApplication.ActiveDocument.ComponentDefinition.Parameters.UserParameters
oParameter=oMyParameter.AddByExpression("Width", "TOP_RAIL_WIDTH", UnitsTypeEnum.kInchLengthUnits)
oParameter.ExposedAsProperty=True
oParameter.Units="in"
[Code]...
The TOP_RAIL parameters are from a linked file.
How do I edit a derived part with a part file and include parameters I'm after?
I cant' seem to work out how to get to the reference components parameters to select whats visible and not visible.
I would like to be able to use iLogic to get the value of the Comment field of a model's parameters. I have some text there that I would like to display in a sketched symbol. The attached image illustrates what I am seeking.
View 2 Replies View RelatedI have an assembly which contains a CComPtr<ComponentOccurrence> pThisCompOcc , and I'd like to do two things.
Get the name of the "base" object, not the display name of the occurence Change the model and user parameter values of the occurrence I suspect that I need to find the function or method which gives me a CComPtr<PartComponentDefinition> pPartCompDef which the occurrence points to for the Q1, but what about Q2?
Presumably the parameters are associated with the Component Occurrence and the "real" name is associated with the Part Component Definition?
I am finally getting time to do some organizational cleanup and management with our templates and vault settings. Many of the things are items that I am altering for each drawing/model I make and I would like to make them "stick" for the company standards. Things like altering font size in the styles library, adding part dimensions to the parameters for the parts list, and creating a new content central library where our part numbers are already populated for the parts list and the structural shapes have datum planes in the middle rather than just at beginning and end.
Inventor Premium 2013 SP1.1
Vault 2013- plain vanilla version
HP G71 notebook
celeron cpu w 4gb RAM and 64 bit system
Win 7 home premium
Wouldn't be nice if you could use part parameters (description, part number, etc...) in the sketch mode text tool?
I'd like to emboss the actual part number on a part without having to retype the part number in manually.