Open SKS.iam which is suppose to be empty, but for some reason asks for the 14020-111.iam file. Once it opens go to the BOM and you will see 24 of the same part in the BOM. If you derive the SKS.iam you will see those 24 parts listed and you will even see them. Yet when you go back to the base SKS.iam they are not visible in the browser or the windows graphic area. IV 2012 sp2
View 8 RepliesI am trying to replace a custom part - created from a content center part - with a copied part with a different name. (I am using the replace tool in an assembly.) However, Inventor is not replacing the part with the part I pick but rather the content center version of it.
View 3 Replies View RelatedOn the main sheet of my drawing I have the overall Parts List. Shows almost all parts except for the few that we don't want to list. On the second sheet I inserted a Parts List to show only parts that are shown in a detail on that page, made the rest non-visible.
On the main sheet there is an item (#13) that has a QTY of 3. Two of those Three are optional parts. What I'm trying to do is insert a custom part into the Parts List, give it an item number of 13A and put in the description "OPTIONAL", then do an Override in the balloon to show 13A.
I get it in the Parts List, Apply it, close it, save the drawing. Looking at the Parts List, item #13A is there, but item #14 is gone. I go back into the Parts List and 13A is there and there's a blue box around the item # and the description. I uncheck Static Value and number 14 shows up (item # and the description).
Then I go over to sheet two, open that Parts List and it lists 13A at the bottom with all the info I added in sheet one and it's non-visible. Go back to sheet one, open the Parts List and there is no 13A to be found.
I am working on an assembly that is designed around a box (bounding box) that could change size. I modeled the bounding box and placed it in a new assembly file. All other parts have been created within the assembly by referencing that bounding box with starting work plane and project geometry.
The problem comes in when I change the bounding box dimensions. The work planes for each additional part, which were defined by the faces of the bounding box, do not move when the sides move. Also, my projected geometry is not updating correctly. This is a simple box, with all 90° corners. So, all associated parts (at this point) are just rectangles.
My parts list on my idw do not update when I make changes to the model. Specifically, I have deleted a bolted connection on my design and replaced with a different components but the parts list table does not update - all I see is a lightning bolt in the browser next to the parts list but I cannot update it here.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
I was using virtual parts to add nuts and bolts to a drawing in 2013
I can make a VP bolt in the assembly, no problem, set it's size, weight, etc.
In the VP itself, there is no option for number of bolts I want it to emulate. For arguement's sake the weight was 1 pound per bolt (they are big bolts).
I can go into the BOM and say quantity 60, hit done and save the assembly.
If i open the drawing, the parts lists shows 60lbs for the 60 bolts total - which it should when summing the weight.
The problem is the BOM/assembly. If the weight of my assembly (without bolts) is 10,000lbs, the assembly sees the VP weighing 1lb and says the total weight is 10,001 lbs. Am i going to have to pattern a fake part to get this to work right? Shouldn't the total weight take into account the quantity set in the Bom??
Is there a way to display the density of materials that are assigned to varius parts in the parts list on a drawing? I don't need the mass of the parts I just need the material density to show up next to their respective parts.
For example, if I have a part with [steel mild] material assinged to it (no matter the size) I need a column in the BOM on the drawing to show: 490.684 lbs/ft^3. "Worry when there's something to worry about."
Had these lines show up in ACAD. I have to restart everything to get them to go away.
View 1 Replies View RelatedInside of the Style& Standard Editor (Manage-> Style editor) we use ANSI and a Company standard created off of ANSI.
But when I choose the filter to ALL STYLES, I can see JIS, DIN, All other unwanted styles. How can I get rid of them?
Do you all have them too? How do you get rid of them if you dint use them?
C1
Inventor Professional 2013
Vault Collaboration 2013
I have an assembly with a lot of purchased parts. I need to create a buy out list for purchasing. I've done this many times in the past and have a template set up for this purpose.
So now the problem, In this assembly, I have subassemblies showing up on my parts only parts list.
One of the subassemblies cinsists of two purchased parts. Both parts are set to purchased in the Bill of materials. If I do a parts only list on this assembly, it works as expected, showing two purchased parts. However, if I put that assembly into a higher level assembly, A parts only parts list shows the assembly instead of the individual parts.
IV 2010 Suite
Been working over an idw MANY times due to project lag.Today I opened it up and tried adding balloons to an already ballooned assembly.
The parts list has not changed, and is "structured".But, if I try adding balloons, they tag each part, not the entire assembly.
Also, I verified this by trying to add another parts list, which defaults to "parts only".
I can't show my data set, b/c it's HUGE, plus it's proprietary.
IV 2010 Suite
Digital Storm PC:
EVGA & Intel components
Win 7 Pro 64 bit
When plotting any IDW files to our full size plotter, I have ghost lines running through the drawing (lines that are not present in the drawing, on screen or preview) alomost like the plotter is printing extra extension lines on the drawings, overlaying 2 sheets on 1 drawings and even moving some text on the drawings. I have all the SP's and am lost. I can move to another computer and print drawings fine so its not a plotter issue.
View 2 Replies View RelatedI want to add a extra section on to the top of the Volute neck so i can keep a perfect shaped circle for the flange i will place on top.How can i add the extra section that retains the perfect circle and also flat across the top for a flange i will place on top..Using Inventor 2012
View 3 Replies View RelatedI have tried to do a lofted flange. It works, but there is an extra bend that I don't understand why it is there. The bends, I would assume, should be symmetrical but they are not. I have attached the part.
View 5 Replies View RelatedI have a 4" pipe tee that was imported to IV from a neutral format ( I don't remember which one. ) In the end view, there are always extra lines showing extending from the branch of the tee.
I can hide the lines, but that then hides the edge lines of a plate welded to the tee branch. Files are attached
Files and more information is already posted on MCADForums:
[URL]........
I have a .idw that I'm trying to make a parts list on. I select parts list and highlight everything. There are two screws that are not showing up on the parts list. I cannot select them manually either. It's acting like they are not there. Even if I do a complete parts list (adding the assemblies parts into one big list), they still don't show up.
How can I select these parts? What is wrong with them that they do not show up in the parts list?
I have been working with an assembly today where it is ideal to mirror parts and have figured out how to reuse the parts rather than create new parts. Now I find that when the parts are mirrored, they ate not retaining the mates. Where do I find the setting so they either retain their mates, or prefferably retain the mirror so that if I move the origional, the mirror moves as well?
View 9 Replies View RelatedI am attempting to model an existing part as it is currently being manufactured a simple hopper, and am having an issue with a corner.
Look at the converging corner of the attached file.
How could this be done to avoid the problem? Or can it? 2010 Suite-SP4 64bit
I am populating iProperty "Description" field using expressions from the custom fields. These custom fields are exported from the parameters.
Is there a way of typing in extra plain text into the field onto the end of the expression without losing the expression formula?
Inventor 2010 Pro SP4, Vault Collaboration 2010
HP Z820 Xeon E5-2643 0 @ 3.3Ghz 16.0GB RAM
Nvidia Quadro 5000
All of the patterned parts in my assembly show up as reference parts in the BOM I have I have opened the base part for the pattern and made sure its BOM is set to normal. When I change the BOM setting in the assembly it automatically changes to reference.
View 2 Replies View RelatedI plan to print some parts but I want to add some bumpy-ness to the surface areas or maybe even a fake metal brush finish look. How do I go about doing that in Inventor?
View 3 Replies View RelatedI've copied over some hardware from the CC to our custom library... washers and bolts. How can I change the BOM structure of the parts to Phantom, I really don't want them showing up in parts lists... and I'd prefer not to just shut off the visibility at that level. They are all set to "Purchased"... can this be changed? I tried opening the part and setting the default to Phantom, but since it is a CC part, I get an error message.
View 3 Replies View RelatedI need to get the dimensions of a lot of centers from parts in a drawing for inspection with a laser tracker.
Is there a way of setting a point from an reference and get a table of the values from the centers I select (x, y and z).
I need to get all the coordinates from the blue and white parts (inside and outside)...
I have created parts, assemblies and drawings . How can i create 2D flat cnc drawings of the components for production? i am in woodwork and manufacturing not metalwork so the whole metal facility in inventor is a little redundant.
Description required on the best process or any process to create 2D cnc drawings from the components? Now, when i say drawings, i do not mean CAM integration. I mean 2D .dwg files of the component that would show say rebate lines, drill holes etc.
It seems like most people output the whole BOM. I only want to data in the Part Number column, preferably as a list of strings.
Here's what I have so far:
foreach (Sheet oSheet2 in aDoc.Sheets){ for (int i = 1; i < (oSheet2.PartsLists.Count+1); i++) { var oPartsList = oSheet2.PartsLists[i]; for(int k = 1; k < oPartsList.PartsListColumns.Count+1; k++) { if (oPartsList.PartsListColumns[k].Title.Equals("PART NUMBER")) { //what goes here??? } } }}
I've made 2 parts and I'm attempting to constrain them but I can't seem to get it to fit properly.The transition should fit at the opposite end of the 2 square cutouts with the square end of the transition inside the cylinder.
View 7 Replies View Relatedis it possible to simply rename a part?
I quite often make up quick parts to try stuff out and call them random things but if I want to change the name it is not just a simple case of renaming the part as a few things need updating.
is there a simple quick way to rename a part in one hit without going through other stuff?
I have 2 different parts that I created as separate ipt files. I then bring them into an assembly and place them how I want, but they have overlapping material. Is it possible to turn these 2 parts into one part? If yes, how?
View 4 Replies View RelatedI have made one part out of 4 different sections. And now I'm trying to combine it into one solid. My thought process was: if I make a derived part out of them it'll automatically make it a solid part. But I'm still having separate surfaces where two should have been united.
View 7 Replies View RelatedHow to lock between 2 parts in Inventor as it in Solid works logo like keylock? So it will move together.
View 8 Replies View RelatedI've been using the "Phantom" BOM Structure to roll up duplicate .ipt's when I have more than one sub-assembly within a higher .iam and it has worked well.
Question - is it possible to adjust settings so that the .iam that I "Phantom" itself remains as a visable line item in the Parts List while still rolling up like .ipt's?