It would be nice to add materials to assemblies..(under the physical properties tab)I see it can be done only if it was a 'weldment' under the weld bead properties, but in weldments you cant have positional reps.
View 9 RepliesIm trying to generate a list of parts and assemblies that has all the quantities included in it.Ive found that if i use the structured view it does not multiply the part count by the number of assemblies, so if i export the bill of materials i wont get the actual number of parts that i require.
If i use the parts only list then it wont include the sub assemblies.the job that im working on has hundreds of sub assemblies and thousands of parts so manually adding them up is not an option.Using Inventor 2014 Pro.
I'm starting to create a library of components, and I have a mix of part files and assembly files. Is it possible to add assemblies to the content center? I cannot "publish" any assemblies, only their respective components.
It's just that for some components, it's easier to create them as an assembly instead of a single component, and I'd like to have pre-assembled components that I can quickly add to my assemblies instead of putting them in one by one every time.
How do I set a constraint where 2 parts are attached to each other but do not phase through. For example if I have a door in a door frame, how do I add a constraint where the door can swing on it's hinges but get stopped by the door frame.
View 1 Replies View RelatedI am working in an Inventor Assembly .iam, I have about 250 fasteners (screws) that are constrained to a flat washer and lock washer. I would like to put them in as a single unit (sub assembly if you will) and then promote or explode them in the top level so that my bom has 250 screws, 250 washers, and 250 lock washers all at the same level, not associated to one another except thru the constraints that were entered in the original assembly. I have tried Promote but that doesn't work because it removes the washers from the original file and I end up with only 1 instance of the assembly. Am I approaching this incorrectly? Is there a better way? I run across this scenario with different components quite often.
View 2 Replies View RelatedIf you have created a sub assembly and inserted it into an upper level assemby, is there a way to bust up the sub assembly at that level?
The issue arising is the individual components need to be called out on the upper level, but in the drawing are all showing up as the same balloon.
Is it possible to add materials to a 2D drawing? I'm working on a floor plan and would like to add flooring materials to it but not sure how or if this is possible?
View 9 Replies View RelatedI have recently landed a job at a design company as an instrument design technician. The last time I touched CAD was about 6 years ago so I have been going through some tutorials. Unfortunately the comany I work for use 2000i so it isn't the most up to date version or anywhere near for that matter but nonetheless I have been perservering (I have both 2011 and 2012 on my pc at home).
How to add materials or textures to 2D objects. I have been going through the tutorials on here (which are brilliant by the way) and I'm doing this one:
[URL]
drawing it has been a breeze now that i have refreshed my memory but I was wondering if I could make it look like the example in the tutorial with the brickwork, water and trees.
i have a valve vault assembly that i am creating that has two headers running through a large cylinder vault. how i get a total BOM if i were to create the header assembly file separate from the the total vault assembly file. is there a way to explode the header assembly bom when i do the drawing.
View 1 Replies View RelatedI recently downloaded a car seat 3d model from turbosquid. It is a OBJ File (.obj). I am having a hard time adding a custom fabric material to the object in Photoshop CS5.5. The material is showing up as a plain blue color and is not adding in the actual pattern of the fabric.
View 4 Replies View RelatedWhen creating custom materials and utilizing them within your Revit project, are the image files embedded within the RVT file and thereby increasing file size? I was needing to know before we load down the project file (.rvt) with many custom materials. Hopefully it is just a pointer to a separate material file.
View 1 Replies View RelatedI'm trying to use assemblies when creating a corridor. The Tool Pallette is emply but I can drag the assembiles in from the Catalog. I've also created an assembly using the ASC. Neither work when I try to use them. The error message is attached.
I'm using a network installation and I do not have the option of changing it to a DVD installation.
I have 2 tanks, each one is an assembly in itself, and they have to be positioned on a steel skid, also an assembly and then interconnecting pipework between the two. My prioblem is that I can't seem to find a way to position the two tanks at a set distance from each other and in relation to the edges of the skid.
Because of this, my pipe router is going all over the place in trying to join up the two termination points.
Will the next release of Inventor have the capability to perform FEA on bolted assemblies?
View 9 Replies View RelatedIn SW I was able to create assemblies that had components with limited motion and then set them as "Fllexable" and allow them to move in larger assemblies. How do I do this in Inventor? I have a trailer with both the front and rear axles able to pivot. These axle sub-assemblies are both able to pivot as top level assemblies but when they are assembled in the trailer assembly the only way I have found to allow movement is to make one axle active and move it then activate the other nad move it. This doesn't work well if there are several interdependant subassemblies that should move together. I am in Inventor 2012.
Inventor Premium 2013 SP1.1
Vault 2013- plain vanilla version
HP G71 notebook
celeron cpu w 4gb RAM and 64 bit system
Win 7 home premium
I use hinges in my door assemblies and they are basically placed into the assembly each time and become flexible so the doors can operate. The hinges are one size and don't change in any way or shape. What is the best practice for inserting these hinges into my door assemblies?
Inventor 2013
Windows 7 Professional 64-bit SP1
HP EliteBook 8470w
Processor: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz
Memory: 16 GB
AMD FirePro M2000
3D Connexion SpacePilot
I have converted a lot of STEP files to .iam files. What is the easiest way to put them in a library? there is realy no need to publish them is them, i already have them in subfolders etc.
View 6 Replies View RelatedWe have some structure issues going on. Below is an example of our current structure.
1. Overall Frame Assy
2. Frame Weldment
3. Spine Weldment
3. Bracket Assy
4. Deck Brackets
4. Air Brackets
4. Hyd Brackets
The biggest problem is we have all of these level 3 and 4 subassemblies that need to reference upper level assemblies to show placement on the drawings. We have tried utilizing LOD's and view reps but still can't fix the problem. The problem comes into play when we get to upper level assemblies that become so huge because of all of the references that are happening at lower levels. It is structured this way to create small BOM's and to be able to use in multiple different structures without having to pull a new Part Number.
We need the reference geometry to be able to show on the drawing our locations of all of these lower level assemblies and how they mount to the frame in their respected locations.
I'm trying to change the BOM structure of some sub-assemblies from "Normal" to "Phantom". However, some are displayed as disabled and therefore do not allow any changes/overrides. How can I enable these in the BOM?
Inventor RS 2011
AutoCAD Mechanical 2011
ASD 2013
Vault Collaboration 2011
Windows 7 Pro
This is using Inventor 2013 Professional.
I've created a simple iPart and want to insert multiple instances of it into an assembly. The plan is to use a parameter-driven iPart to create multiple variations on the same basic model which will eventually be lasercut.
I've included a sample archive. 2DiPart is a simple part with a couple parameters. 2Dassembly is where I've tried to include this part. I'm able to walk through all the dialogs to place the iPart, and will even see it in the canvas as I select the insertion point. However, after I dismiss the dialog, nothing shows up in the canvas. I'm still able to see the component instances in the project explorer however.
How to best to get multiple instances of a parametric iPart into a drawing that can be lasercut.
What is the best setting for shrink wrapping an assembly?
I've found shrink wrapping it as a surface causes problems with the video card when rotating the model and placing views on a drawing.
I'm having a problem highlighting parts within a sub assembly. A simple structure to demonstarte this issue would be:
TopLevel.iam
|
SubAssy.iam
|
ChildPart1.ipt
ChildPart2.ipt
Using this structure I wish to highligh ChildPart1.ipt, howver my vba macro code below doesn't seem to work (nothing happens):
Public Sub Highlight()
Dim SubAssy As Inventor.AssemblyDocument
Dim ChildPart1 As Inventor.ComponentOccurrence
[Code].....
I have assembly with over 100 sub assemblies. I need to export the COG for each sub assembly to excel. The COG must be in relation to the parent assembly's origin point.
I can get coordinates manualy (right click on sub assembly - iProperties-Phisical), but it is take a lots of time.
Autodesk Inventor Professional 2013
Windows 7 64-bit
Is there any easy way to turn off visibility for all datum planes when opening a Pro/E assembly in Inventor 2010? It is incredibly time-consuming, not to mention irritating, to click through and hide them all.
View 3 Replies View RelatedI'm trying to take multiple parts of the same type and make them into one .ipt I began doing this and It seemed to be working fine. When I put those grouped .ipts into an .iam, Inventor creates a Subfolder of each .ipt and fills it with each part from that group and now those created ipts are unique unlinked parts (unlinked to the group ipt). I'm trying to reduce our file count and link our .ipts and .idws/.dwgs so this Inventor file creator results in the opposite of what I'm looking for. My question now is is there any way to modify this process to work the way I need it to or is there a completely different way that I should be doing this?
View 4 Replies View RelatedHow do you limit translation/rotation of components in Assembly mode? I'm volunteering as a teacher to some high school students and we're modeling a robotic arm using syringes as prime movers. I want to keep the linkages from traveling inside-out and limit the travel of the syringe plunger.
View 9 Replies View RelatedI have a spring that is used in multiple assemblies and in each assembly the compressed length is different. Plus the amount of compression is different.
What is the best way to model the spring so if I change the WD or OD, etc. all assemblies would update?
I tried adaptive, but that seemed to limit the relationship to a one-to-one not a one-to-many.
If I used iPart or the spring was derived from a table, where the OD & WD were constant, would the assembly models change when I changed these values?
how the file structure works and how to link parts (ipt) and assemblies (iam) to each other. I converted a large file from Mechanical desktop to inventor which was a two day process. All parts and assemblies for the main assembly were dumped into one directory. I would like to move all the part files to one location and the assembly files (sub assemblies) to another location and then tell inventor to go there and pick the items from those two locations. I have set up the project telling inventor where to go and look. I moved all the items out of the original directory and now when I open the main model assembly I have to resolve the link to each part individually. This will take forever, is there a way to have inventor go and look for the parts and assemblies without me having to resolve each one?
View 3 Replies View RelatedIf I want to control a mechanism assembly, like an excavator, on screen with a couple of joysticks, how can this be done?
The idea is to test the suitability of mechansims and their controls.
I have a master assembly containing three sub-assemblies 1, 2 & 3.I require 3 Drawings from this master assembly.
Drawing 1 showing master assembly, sub-assemblies 1 in full and 2 & 3 in reference.
Drawing 2 showing master assembly, sub-assemblies 2 in full and 1 & 3 in reference.
Drawing 3 showing master assembly, sub-assemblies 3 in full and 1 & 2 in reference.
This sounds so simple but is it possible?We have tried all manner of configurations with LOD.I'm not really keen on locking design views as the assemblies can change at any time.
I got here on in my templates, two types of weight - net and gross. I've changed the main property MASS of each PART to be the GROSS weight, so when i have one assembly i always get the total gross weight.
And when i wanna get the NET, I open the BOM, show the proper column with this net weight and then export do XLS to sum all of then..
Now the doubt is, to get the things easier, is there a way to put some code in the assemblies, that could sum all the properties "X" from each part and sub assemblie to get the total net weight ?