Trying to add a radius in a corner and its not cooperating. Take a look at this image. Notice how the one radius curves around the part, but the other one does not? I know these two look different because they are different sizes. I would like to get the 1in radius to go straight across like the R3/4, but it will not do it. I've tried the options under the chevron, but nothing gives me what I want.
View 9 RepliesI'm grading this pad site from EL.215 to EL213 at a 2:1 slope. I use "grade to elevation" but I don't want the corner to fillet. I need the grading to fill in to the retaining wall (red line). I tried using infill but I can't get the fill slope display to show up.
View 9 Replies View Relatedis there a way to figure out the radius of a corner in Corel Draw X5 if it is a curve?
View 7 Replies View RelatedWhat is the best way to radius a corner?
i.e. I have two lines: one is horizontal, and in this case the other is at 45 degrees, and at the point where the join I want to create an exact radius. So that one line curves into the other, following an exact arc.
What is the easiest/best way to create this?
Specify the corner radius of a rounded rectangle?
View 13 Replies View RelatedThe first instruction is .. "Make a 10 pixel selection as shown in figure 2 - it needs to be a perfect selection, exactly on the top left corner of the tab". I did that ..
The next instruction is,
"Now select:
Image/Crop
(Need a 10 pixel radius corner.)"
His image then looks like this ..So how do I do it?
The course is at [URL] and I want to make the navigation tabs.
Is it possible to find the value of the corner radius of the rounded corners for a rectangle that was created with the Rounded Rectangle Tool. This if for CS4.
View 6 Replies View RelatedIs it possible to change the radius corner setings of the Rectangular Marquee Tool?
I want to select an area into which I want to paste an image but I want rounded corners such as this below which I made with the Rounded Rectangle Tool:
how to do a rwdius on a hex nut as shows in attached JPEG image. I am attaching my ipt file as well without radius.
View 2 Replies View RelatedWe need to be able to use intersection with radius... In doing, it just snaps to the center not intersection.
View 9 Replies View RelatedI have a banner heading that is more or less outlined text. I want to give all the corners a rounded corner and at the moment would just do it all by hand, one at a time. So I want to go from a to b:
But I would like to find an easy way to make all corners the same diameter regardless of the angle too.
How can I create a hem in a corner? The default setup overlaps them and throws an error. A simple "miter" will correct the problem, but I cannot figure out how to do it!
View 4 Replies View RelatedI have been trying to bend a larger radius on a corner bend but i can not seem to be able to . I start out with a face of 46" x 82" i want to put a 1/2" bend up then a 1/2" bend out to make a z shape i'm using as a material .109 stainless steel and i want to end up with a 1/2" on the inside corners so that when i'm done i can flatten it out to get the proper sheer size for the piece the metal brake i'm using has a 1/2" die in thats why i trying to figure this out is their any way to put this kind of radius on the sheet metal bends.
View 2 Replies View RelatedI just had to reinstall Inventor and I forget how to remove the annoying radial menu that pops up whenever I right click. I just want the normal right click menu.
Inventor 2013
Windows XP
I have been able to dimension any circle on the drawing， but if there're several circles with the same radius ,I just don't know how to dimension the circles with the same radius with only one dimension.
View 1 Replies View RelatedI'm still new using autodesk inventor and still learning. I have trouble to cut the plate (Penahan Depan.ipt) follow the radius of the roll (Roll.ipt).
View 4 Replies View RelatedI would like to radius the edge of a block for about 1" along a 3" edge. In Solid-doesn't-Works I would select an eddge to radius and then would edit it pulling one end of the line to radius back to the desired length of the radius.Here I find no option to edit the edge, I have also tried splitting the edge but I can't seem to make that feature work. Is there a way to do this short of creating a work plane at one end of the edge and then creating a cut to a set depth?
Inventor Premium 2013 SP1.1
Vault 2013- plain vanilla version
HP G71 notebook
celeron cpu w 4gb RAM and 64 bit system
Win 7 home premium
I have chamfer going around my part but I need to make it to stop 2mm's before the corner. How is this done?
View 2 Replies View RelatedIs there a way to preload information into Inventor in regards to the break press such as the dies being used or the ones available so the when the computer is deciding a bending radius,it know what tool we have?
Currently the bend radius is set to "radius", which i am assuming is default, but I can't figure out how to change that either, and depending on the thickness it will change, but like today it said I would need a 1/16th inch radius, but we don't have a 1/16th inch die,it is an 85 degree air bending setup,and has a 4 way die with smaller and bigger openings.
I am trying to edit my drawing template dimension style to always do a diameter (if it is a circle). Right now it defaults to radius and I manually right click and change it. I found all sorts of styles for how it displays the radius and diameter, but didn't find where to set the default.
View 7 Replies View Relatedhow to change the bend radius on a flange that has several different bend radii with the same metal thickness. For example, I have a sheet metal part that is 1/4" thick and has one bend radius that needs to be .030". How can I change the bend radius?
View 2 Replies View RelatedHow do I change this dimension into a diameter dimension?
I have tried editing the dimension style to display as a diameter and it doesn't change it. I tried creating a new dimension style and it doesn't change it.
My company is trying to Standardize all drawings produced to 1 format. the one we are attempting to create would be in the form of: nominal upper limit^lower limit. this is easily acheived in autocad and linear, chamfer, and hole/thread dimensions in inventor. but radii's and diameters from a round surface (as apposed to linear diameters) we have run into a snag with. We cannot seem to find a way to either remove the prefix symbols or be able to insert text between the symbol and tolerance.
below is a illistration of the problem and the form of the new dimensions.
We have an issue where we are trying to bend a 1mm sheet with a 24mm radius. The one side must come out 105mm wide and the flange must be 50 mm wide. inventor gives a flat pattern width of 143.4
If we bend using a brake press and a 24mm tube blade then it wont come out the right size. its like the flat pattern isn't big enough. we get the 50 mm flange but whats left over is 99 and not 105. How do we deal with something like this?
Trying to apply a variable radius to a part. The direction of the radius is wrong (pointed back in toward the part) and I cant get it to go the other way. As long as all the fillets along the curve are the same radius, the fillet will compute, but if I make them vary, then it fails.
View 2 Replies View Relateddimension bend parts with corner intersection. Is there any option in Autodesk Invenor Drawing so that i can give dimensions as shown in attached image.
View 2 Replies View RelatedI was just wondering if there is an easier method of getting a 45 degree corner on flanges of 2 different sizes. 1 flange is 1" and the other is .75". I have been cutting the .75" flange down and adding to the face of the 1" flange.
The corner I'm talking about is on the far right of the part.
How to joint this corner together for becoming 45 degree corner shape?
View 9 Replies View RelatedI have couple of problems that I haven't managed yet on my own.
1. How I can get "smooth" bends without those "steps"? See part: Smooth Bend
2. How I can round that Flange's "inside" corner? Just smooth Corner Round like those other corners have. See part: Corner Round
Been toying with sheet metal stuff here lately. Going from solid modeling to this feels kind of backwards to how you design.
Anyways, I have part (attached). 300° round. So far checks out to how I want. Please look at chamfer #2. It is in the correct location, but it is not letting me do what I want...maybe I havent started this simple peice in the correct fashion.. What I need is the chamfer in the same 'wall' where it is, but I need it 4.97° x 23" long AROUND the part.
Inventor 2014 PDS
The question is if I have designed a part in sheet metal with multiple flanges and one of my edges follow a specific radius. Is is possible to use contour roll or any other means to create a flange on that edge that will allow me to flatten that out. I cant see it being physically possible putting a bend in there as the material would need to stretch and the bend tool would need to follow that radius.
View 2 Replies View Related