AutoCAD Dynamic Blocks :: Finding A Column Grid Bubble?
May 21, 2008
We are looking for a column grid bubble dynamic block that will allow us to place horizontal or vertical grid lines while the text in the bubble remains in the upright position.
Another thing we need is to allow for column lines close together without overlapping bubbles. In other words, we need to have the ability to have a diagonal line from the bottom or side of the bubble to the column line which allows us to have all bubbles aligned no matter how close the columns grid lines are.
The attribute in the bubble has to be able to have XX.X to fit within the bubble with the first to X's to be either Alpha or Numeric and the last X to be Numeric only.
I have an associative hatch in a dynamic section bubble that updates as the arrow rotates around an ellipse.
Everything works fine until the block is scaled. The block is not annotative, and needs to be scaled to the drawing scale. Is this an autocad issue or am i doing something wrong?
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
Im looking for a way to automate my drafting tasks, and this time I want to automate the creation of structural steel grid quickly as possible.
I was thinking about creating a dynamic block with all my drawing needs, and then use an array action to multiply it as I go, but I cant use it since the cell size inside the block is static .
Another idea I had is to create a dynamic block with fixed number of cell and columns, I gave to the dividers a starch action with divided multiplier. its working but its not practical because wit this method I have to create another million of grids(I attach this block )
I'm making a dynamic block of a column radiator. Like all column radiators, this particular model comes in a range of heights, and a range of standard widths. But, because it's a cloumn radiator, you can always add another column, so making a non-standard width. There's usually a small cost associated with going with a non-standard width.
1. Is there a (fairly) simple way to represent this concept within a Dynamic Block? 2. At the moment, I'm ignoring this fact and just have a long list of all the valid increments. I did it as a list (as opposed to increments) so that the user could easily see what length they were providing.
As I see it, the downside of this approach is that the base point of the block is at one end of the radiator, rather than in the middle, so in most cases, if you stretch the block, you also have to reposition it. The best option would be to be able to choose whether the base point was in the middle or at one end (with the default being in the middle) but, and here's my question, if the base point is in the middle won't the list values be half their actual value? This would make radiator selection even more tediuos and confusing than it already is!
I am using the Enhanced Custom Grid in Architecture 2014. Everything is right about the grid except that the text inside the bubbles is mirrored. I am looking at the plan view (not the bottom) and my UCS is square to the world so I'm not sure what's going on.
I'm having an issue with creating a column bubble block that would have an attribute and both be annotative.
I've created a 3/8" dia circle with 3/16" text and the text is NOT annotative. The bottom of the circle is at 0,0 with the text justification at MC
I create the block of the circle and text and make it annotative and save
When I insert it into another drawing, the block inserts properly and scales as desired. The issue is when inserted, I'm NOT given the option to fill in the column # attribute. I can double click and enter text, but this should happen during insertion.
When I create the block, if I do NOT select the attribute as part of the block, I am given the option for the attribute during insertion but it does not scale automatically.
What am I doing wrong? I'm attaching my block as an example.
i have created some dynamic title blocks with text attributes in title column. I have gone back an added some more attributes at a later date and these new ones will not move with my dynamic stretch! I have tried everything, modifying the action, re-doing the action, nothing works!
I'm trying to create a 3 digit grid bubble that will align vertically along an elevation, but my grid bubble in use within the project insists on the text being horizontal... Is there any way to force the alignment to vertical...?
I've made annotative blocks and I've made dynamic blocks... My intent is to integrate both but I can't find a way to move dynamic block parameters separately at different annotative scales.
In other words, if I insert an annotative dimension and add multiple scales I can move the dimension grips independently at each scale. If I insert a dynamic block I want to be able to use the dynamic block's action "grips" to do the same. However, with a dynamic block, if I move a stretch action at one annotation scale it moves the action at all annotation scales.
I am having trouble using the beam and column calculator in Autodesk Inventor. When I choose the beam that I want to test all the dimensions are not being put in automatically.
This is happening with most types of beams that I import from the CC the angle (6X3-1/2X3/8) that I am trying to test is getting no Wx, Wy, Wk or Jk. and the I beam (W6X25) is not getting Wk and Jk.
I have created a dynamic block with several visiblility states. The block works great for what I need it for. however, I am trying to add one more action to the block but am having issues.
This block is essentially a 24" retail cabinet with the visibility states showing the different drawer and shelf configurations. I want to be able to lengthen the cabinet in 24" increments and have the visibility show for each 24" section.....e.g. I want a 10' cabinet so I bring in the 24" starter block. Then stretch the cabinet to the 10' mark, then I can chose any drawer/shelve config for each 24" section (they are all different).
I can get the block to stretch in 24" sections....no problem.....i just want the visibility state to be duplicated as well for each section. Now as it stretches, there is only one Vis state and it only populates the first cabinet.
I could do this by copying the block over and over 5 times.....but I am hoping there is a way to make this dynamic.
I have a block I am making into a Dynamic Block. I will be adding in different visibility states. Depending on the visibility state the block would need to be inserted from a different point.
My question is, is it possible to add multiple insertion points to a dynamic block so depending on the visibility state it defaults to the correct insertion point?
Is there anyway to link standard AutoCAD Grips and there commands to Dynamic Block Actions? I want to stretch an arc by its midpoint grip. This accomplishes something that no other commands do.
I am using AutoCAD 2013 - Educational Version, and I want to convert my linework into a column grid. For some reason the COLUMNGRIDADD command is not being recognized by the program. When I type it in the command line, it just says Unknown Command.
Additionally, my Build Panel is missing from the ribbon, which is the other source for the column grid tools. I tried to reload or change the CUI, but so far this has not been successful.
Using Architecture 2012 and seem unable to get a column grid to show automatically in elevation views. Looks fine in plan view, bubbles etc all working once we sorted out annotative setting .
I am trying to get an extra column of grid to the left of my sections. Is this a way to do this? Do I need to have white space in this area and not a grid?
Civil 3D 2012 SP4.0 Windows 7 Enterprise 64-bit C3D 2014 SP1 Dell M6600, Core i7 @ 2.3GHz, 16 GB ram Dell T3500 workstation, too much ram to post
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
I need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
I need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
