AutoCAD Dynamic Blocks :: Stretch Or Array (JPG)
Oct 30, 2013
I have been working on a dynamic block that need to look like the attached jpg. Basically it needs to be able to stretch up to 50'-0" but in ten foot segments (part size limits) +/- an additional but in 1 foot increments.
I've got two blocks that will either array or stretch. But have not been able to get it to match the actual requirements. I have attached my current block attempt. Also as you can see from the jpg, the support posts usually alternate as well and I haven't figured that out yet either .
View 9 Replies
ADVERTISEMENT
Aug 12, 2013
I'm trying to create a block for angled handicapped parking stalls.
I used an array chained to a stretch in order to increase the number of stalls. It worked but for some reason it does not work in all of my visibility states. In some visibility states the array and stretch do not stretch together. The block should end with a stall but some end with a line and no stalls above it.
I attached a drawing with the blocks. The block named "STALLS-60-HANDI" it works correctly except in visibility state 9' and in "STALLS-60-4space Handi" it only works in visibility state 10'.
rename to dwg . fire wall would let dwg posting
View 4 Replies
View Related
Jul 31, 2012
I need this block to do the following:
1. Move the right piece so it ends at 3', 4', & 5'.
2. the move right hook and 'backing' to stretch/copy (or array) so it adds a hook to the right and fills in the backing.
so this means that a 3' gets 4 hooks, 4' gets 5 hooks and 5' gets 6 hooks.
3. the block as shown is the smallest configuration with 3 hooks.
I could just set up a visibility and draw each one at it's appropriate length but I'm trying to keep this simple block to a min size. If all else fails, that's the route I'll take.
I've tried a couple different configurations and I keep getting duplicates or the end piece doesn't move the correct distance.
View 3 Replies
View Related
Jan 28, 2011
Sure wish you could manipulate the Column Offset of an Array Action with a Stretch Action.
CSHADEDESIGN|AUTOCAD LT|LT-KB|DYNAMIC BLOCKS
View 2 Replies
View Related
Feb 3, 2012
In the attached dwg, I have a dynamic block "Platform" which is used several times. I have an adjustable length, with the array set to repeat the toggles (end view of 2x4) every 2', not including the last 6". That works perfectly, except one thing. "Distance1" is the distance of the parameter, because this was the only way that I found to stop the array from showing up within 6" of the last toggle. When I insert "Platform," and click the arrow to stretch it, I can type in the distance desired minus 6", and I'll get the correct length of platform. However, I'd like to be able to type in the actual length, and have the array work appropriately (the same way it does now).
Then, I'd like to create a custom toolbar that has a button to click which will insert this platform and ask me what the length of the platform should be (the entire distance). After specifying an insertion point, the block will insert at the correct length, with the appropriate toggles.
Here's what I'd like to do with it: using datalink, I'd like to count the following: how many copies of each length of platform is in the drawing, with toggle count and length of platform specified. I have already figured out the datalink to get the value of "Distance1", it's only the issue with the toggle count that I'm trying to figure out.
View 0 Replies
View Related
Dec 6, 2007
i'm trying to do a polar stretch and array for rigid insulation. RIGID2.dwg is my best option. but as you can see in the jpg, the first line should have arrayed already, because the gap is over 2". i tried to follow the instruction someone used for the clothes hangers URL.... and it resulted in RIGID.dwg, with the lines rotating off the main line.
View 9 Replies
View Related
Feb 4, 2011
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
View 9 Replies
View Related
May 5, 2012
I have a block of a roof screen. What i want to do is to stretch it & have the slats on the front & also the supports on the rear array @ different intervals. The slats on the front would array every 6-1/2" (The slats are 5-1/2" wide with a 1" gap). The supports array every 4'-0". I have tried to do this multiple ways with mixed results. How to get my desired outcome. I am enclosing my block.
View 5 Replies
View Related
Apr 4, 2012
Is there a way to have the grip stay in the correct position when the distance multiplier is .5? It seems to "get ahead" of the original location.
In the attached block, when I stretch the block with the grip, the grip ends up off the end point. Both actions have a .5 multiplier, with the left side having a rotation of 180 - so both sides stretch equally in opposite directions.
Also, there are 3 views with parameters (width/depth). Is there a way to get the user to enter in the sizes without having to select the size on each view? Basically a table that has a 'user input' field so the size selected changes everything at one time.
View 7 Replies
View Related
Jul 4, 2013
How do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.
View 2 Replies
View Related
Nov 21, 2013
I have created a small dynamic block that manipulated some lines (attached). The properties table allows s1, b1, b2 and c to be modified. The white lines control the cyan and red.
The red-lines have an array within (green lines) which I want to lock to the blue line parametrically. The array may be dragged physically but thats not the point; its need to be automatic (Revit style).
View 3 Replies
View Related
Nov 24, 2013
I have been trying to get my 2D parametric model to work and am having trouble with the array.
I attach the model. When I alter the span in the properties palette, I want the array to follow. I do not want the grip to show as I eventually want to program the dimensions externally.I do not mind using AutoLisp or .net if I need to control the model using code.
View 9 Replies
View Related
Apr 3, 2012
Is it possible to modoify an array on the fly?
I've been playing around with an incrementing block, and have figured that you can get an attribute block to report its position relative to its origin inside a block,and have it report that back. If you can do that and do formulas, you could then have that creating an incrementing number. If however you were to want to use such a block for counting stairs or alternatively counting car parking spaces, and want to get the spacing of the array just right, you seem to have no choice in the size of array other than when editing the block?
Attached is what I have simply created. No calculations, just reports the position in X, but shows the possibilities. Stretch the text out and you get more numbers.
Time consuming to create alternative is to have to define each number object individually and do a move action, based on something like an object being stretched (length of stretched object becomes part of a multiplication factor for a move action). See Numbers increasing block attached. More precise but takes a while to create, and is limited to the numbers shown.
View 7 Replies
View Related
Dec 14, 2012
I'm using a 2-2D recangles that are 5'x16" and 10'x16" and I am trying to figure out how to array this in one direction, to the left, but have the array on 5' increments. Also, within each rectangle I am needing text to show which size it is.
e.g. If I drag the array to the left more than 10' but less than 15' it will apply 15'.
View 7 Replies
View Related
Nov 20, 2013
I've created a dynamic block with listed increments e.g. 36, 42, 48 inches width. The dynamic window block that comes with autocad has the same incremental stretch.
This block shows the tick marks as well as a the value in a dynamic input box. How can I have the value displayed in my custom dynamic block. All I have is the "tick" marks.
View 6 Replies
View Related
Nov 16, 2011
If you have a drawing open and the Tool Palette Architectural open click on the door. It has "tick marks" where you can stretch the doors opening to (24", 32"). I want to know how to add those "tick marks" to my blocks .
View 4 Replies
View Related
Mar 23, 2012
Attached is a block that I am using for Finish plans. Basically how it works is that it is suppose to be inserted and then stretched to indicate a finish change in the floor. When I insert it and stretch it, it works exactly as I want it, but when the scale is changed, the center tag resets to the original center before the block is stretched. I would like it to stay in the center relative to the line that is stretched.
Not sure if you understand, but if you are good with dynamic blocks. You will notice that the dot is annotative where as the line that stretchs is not. I cant have the line change because it will be stretched between two areas with different floor finishes and that will stay consistant. I want the block to adjust so that it is the same size on all the scales of the drawing.
View 9 Replies
View Related
Jun 3, 2013
I have been looking for about three days on how to do the array with-in the dynamic blocks, but have been very unsuccessful. What I am trying to do is make a TJI joist that you can have a look up table that is classified as 'offset' so that you can eventually strech the joists to standard spacing, and use the array to work. So that I dont have to have a ton / zero visibiliy states.
View 1 Replies
View Related
May 22, 2013
i work at a small structural firm and am about the most experienced cad user here, which isn't saying much. I have never wrote any LISP's or anything, but have created many dynamic blocks and have edited some programing my boss got from a previous employee for adding dropdown menus with blocks/layers/etc. Just so you know my level of knowledge when it comes to answering my question. Also I am limited to using 2009 but other co-workers have up to 2013 so i would like this to work for all users. And i have done a bit of research but based on everyone elses level of knowledge am finding a lot of conflicting info and solutions that, to me, are in another language.
So I have a table that is created using polylines and text. It's a funky shape and AutoCAD's tables are a pain for it. i have created a dynamic block where i can array the rows down and the columns left. The issue is, i would like the test to come with each row, but still be editable once the block is done. I have figured out if row one is composed of 5 columns of text put into a single attribute, it is fine. But once you use the array action, to say 3 rows (including now 3 sets of attributes) they are not editable. So what is the work around, if there is indeed a work around?
the two option i see are to only array the rows and columns and left the text outside that block and manually copy it done to how ever many rows the user needs.... Or to have 2 blocks come in together, one as described before, and the other which just arrays the text and then i explode it to edit each line.. but then if you later choose to addd another line you would be left with doing that manually anyway..
View 2 Replies
View Related
Feb 28, 2012
I'm attempting to use Excel to take data from a drawing and give me purchase and cut lists.
I have successfully pulled the overall measurement from my dwg, and inserted it into a workbook. What I'd like to do now is to have a count of how many times the array function went into effect. For example, attached is a file containing a block called platform. When stretched, it inserts toggles every 2'. When I export the information from my dwg, I'd like for the program to not only extract the length, but how many toggles were inserted for each platform.
View 1 Replies
View Related
Nov 6, 2007
i made a simple little chair block , that can be dynamically pulled into theatre seating.
I am trying to get the "Count of Objects" revealed as mtext or an attribute in the block.
It seems that doing area mathematics on the total array size divided by the individual column/row sizes will give me the correct count.
Any recommendations on the "Field" that will work with this?
View 6 Replies
View Related
Dec 12, 2013
I have drawn a simple block that I want to stretch in two directions manually or from the properties palatte.
My block works fine once and then breaks down. Stretch the block in the 'Y' direction. Deselect the block. Stretch the block again and only the grip moves. Edit the block and close the block, the block resets.
View 6 Replies
View Related
Nov 23, 2011
if it's possible to link a rotation with a stretching action. I have a text (or an attribute) inside a box that can be stretched. But if the box becomes too small to hold the text horizontally, I would like that the text automatically rotate vertically without any other action that stretching the box. If that is possible, is it also possible that instead of a text, there's an attribute, and that it rotates according to the attribute's length ?
View 9 Replies
View Related
Jul 5, 2013
See attached DWG. Two offset arrows.
This works as long as it is not rotated, but distorts if rotated and then stretched.
I'm using ACAD2006.
View 5 Replies
View Related
Jan 11, 2012
I created a dynamic block with a polar stretch. I insert the block, then have to select the grip to rotate/stretch it. Can it be inserted and then rotated/stretched all in one action? The insertion point is at one of the line and the polar stretch grip is at the other end.
View 3 Replies
View Related
May 9, 2013
I would like to stretch my extruded shelf using a list of value settings.
I completed the steps in block edit but it will only allow my object to move to my value sets.
In 2D I have no issue.
What am I missing when modifying 3D objects.
See attached blocks.
View 9 Replies
View Related
Sep 28, 2013
I have a linear stretch D1:
Distance Type: Increment
Dist Increment: 1
Dist Minimum: 1
Dist Maximum: unlimited
I also have a linear stretch D2:
Distance Type: Increment
Dist Increment: 1
Dist Minimum: 1
Dist Maximum: is it possible to set the maximum distance to equal D1-2.5??
Both linear stretch D1 and D2 can be stretched independently. So D1 may be stretched to 100, and D2 may be stretched to 50, but what I am trying to do is ensure that D2 will never stretch beyond the distance of D1.
View 1 Replies
View Related
May 22, 2013
I was wondering if it is possible to use dynamic blocks to stretch a rectangle evenly, using only 1 point? I have attached a PDF of a rectangle with 2 lines coming out of each side (before & after picture). I want to use dynamic blocks to pick a point at the top right of the block, so that when I pull it out, the lines will extend, but stay attached to the rectangle. I also what the rectangle to stay in the center at all times.
View 9 Replies
View Related
Jan 12, 2012
I have attached a drawing that I am trying to stretch two lines - one lengthen and one shorten as I rotate the connecting line.
View 4 Replies
View Related
Oct 18, 2012
See the dwg attached.
I'd like to modify a dynamic door block I've created so that I can stretch by door leaf size OR structural opening size, but I'm not sure how to do this.
Incidentally, I think the block has some flaws:
- I think the 'center/flip point' is not exactly in the center!
- The frame size should be 40mm, not 32mm
- The packing zone should be 30mm, not 6.38mm!
View 8 Replies
View Related
Jul 15, 2013
I foolishly thought i'd sorted making hatch work within a dynamic block that requires user input to set length and width of block...the hatch would fill to the revised size when the user sets the length and width in the properties dialogue...woohoo. Off I go home from work having defeated the nemesis of the day.
Open up my drawing today and can I get the hatch to act as it did yesterday?
I built my block (a simple rectangle all told) added my parameters in block editor. length and width linear actions with 0 grips as I don't want stretching by grips. Added the stretch actions. Tested the block (without hatch)...working. Only then did I hatch, so into block editor and using associative, send to back, normal island detection and selecting the rectangle to hatch. tested block ...working. great. Inserted the block into new drawing...working.
Opened AutoCAD today...Not working...hatch remaining as original size
Tried building new block exactly as I did yesterday...no joy...
On a side note...it works if I leave grips on but only if I use the grips to activate the hatch (it still doesn't work by just typing into properties though) that's not going to cut it as I don't want to be telling everyone to wiggle the grips so to speak.
View 7 Replies
View Related
