i'm trying to do a polar stretch and array for rigid insulation. RIGID2.dwg is my best option. but as you can see in the jpg, the first line should have arrayed already, because the gap is over 2". i tried to follow the instruction someone used for the clothes hangers URL.... and it resulted in RIGID.dwg, with the lines rotating off the main line.
View 9 RepliesI've made this block . when i rotate the vertical line I need to add lines every 15° as you see in the image, i've seen that polar array is not possible in the dynamic blocks.
View 8 Replies View RelatedI am trying to put a polar stretch on the block uploaded, but it doesn't seems to work (maybe because of my constraint? ). If something major is wrong with it, is there another way I can make the same drawing proportional when i rotate it and stretch it ? Also, after that I have to use it for vlisp.
View 5 Replies View RelatedIn the attached dwg, I have a dynamic block "Platform" which is used several times. I have an adjustable length, with the array set to repeat the toggles (end view of 2x4) every 2', not including the last 6". That works perfectly, except one thing. "Distance1" is the distance of the parameter, because this was the only way that I found to stop the array from showing up within 6" of the last toggle. When I insert "Platform," and click the arrow to stretch it, I can type in the distance desired minus 6", and I'll get the correct length of platform. However, I'd like to be able to type in the actual length, and have the array work appropriately (the same way it does now).
Then, I'd like to create a custom toolbar that has a button to click which will insert this platform and ask me what the length of the platform should be (the entire distance). After specifying an insertion point, the block will insert at the correct length, with the appropriate toggles.
Here's what I'd like to do with it: using datalink, I'd like to count the following: how many copies of each length of platform is in the drawing, with toggle count and length of platform specified. I have already figured out the datalink to get the value of "Distance1", it's only the issue with the toggle count that I'm trying to figure out.
I need this block to do the following:
1. Move the right piece so it ends at 3', 4', & 5'.
2. the move right hook and 'backing' to stretch/copy (or array) so it adds a hook to the right and fills in the backing.
so this means that a 3' gets 4 hooks, 4' gets 5 hooks and 5' gets 6 hooks.
3. the block as shown is the smallest configuration with 3 hooks.
I could just set up a visibility and draw each one at it's appropriate length but I'm trying to keep this simple block to a min size. If all else fails, that's the route I'll take.
I've tried a couple different configurations and I keep getting duplicates or the end piece doesn't move the correct distance.
I am trying to be able to have my outreach arm stretch horizontally and on angles of 5 / 10 / 15 degrees from the pole. I have been able to make the polar stretch for this and it works fine though what i am trying to do is have the luminaire height also stretch and move when the size of the outreach changes (i can make the linear dimension work the way i want though not the luminaire parameter) as when you add the paremter into the stretch action is only moves the top and leaves the bottom at the same location which is not giving me the correct height.
The block itself is alot more complicated then this I have stripped most of the parameters out to make it less confusing but the end result would allow the user to input the outreach angle, outreach length and luminaire height. I have attached drawing for your reference.
The linear stretch works fine but changing the length affects the position of the tick marks of the polar stretch. If I change the degrees to 0-360 then it's not a problem but I want to restrict to 285-345 deg.
I can't figure out how to move the base angle of the polar stretch with the linear stretch.
I have been working on a dynamic block that need to look like the attached jpg. Basically it needs to be able to stretch up to 50'-0" but in ten foot segments (part size limits) +/- an additional but in 1 foot increments.
I've got two blocks that will either array or stretch. But have not been able to get it to match the actual requirements. I have attached my current block attempt. Also as you can see from the jpg, the support posts usually alternate as well and I haven't figured that out yet either .
I'm trying to create a block for angled handicapped parking stalls.
I used an array chained to a stretch in order to increase the number of stalls. It worked but for some reason it does not work in all of my visibility states. In some visibility states the array and stretch do not stretch together. The block should end with a stall but some end with a line and no stalls above it.
I attached a drawing with the blocks. The block named "STALLS-60-HANDI" it works correctly except in visibility state 9' and in "STALLS-60-4space Handi" it only works in visibility state 10'.
rename to dwg . fire wall would let dwg posting
I use autocad 2011 LT and I have some problem with polar stretching!I have to get from A(see picture) to B but C is always happening! I want to put in an angle in te propertieswindow so that I become B. the angle is variable but the middle stays the same length!
View 4 Replies View RelatedI have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
I have a block of a roof screen. What i want to do is to stretch it & have the slats on the front & also the supports on the rear array @ different intervals. The slats on the front would array every 6-1/2" (The slats are 5-1/2" wide with a 1" gap). The supports array every 4'-0". I have tried to do this multiple ways with mixed results. How to get my desired outcome. I am enclosing my block.
View 5 Replies View RelatedHow do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.
View 2 Replies View Relatedmy problem is whenever i make a new block a stretch point appears even if its not a dynamic block . also its not a stretch point, because when i click on it, it just move the block , and it always appear on the coordinates 0,0 it cause me a problem when I insert the block , autocad use this point as a base point , and its very far from the real block .
View 1 Replies View RelatedI am trying to insert a dynamic block and position and stretch the block, using the linear parameters, depending on values entered into a form.
I managed to create a form that would draw a series of boxes. And i managed to create a routine that would insert a block and size it depending on fixed values but i can't link the 2 together.
Win 7 Pro 64bit, Dell Precision M6500
I am trying to create a block that polar arrays the street lamp, but every time i try i just move the grip for it, is there something i am missing?
View 8 Replies View RelatedSure wish you could manipulate the Column Offset of an Array Action with a Stretch Action.
CSHADEDESIGN|AUTOCAD LT|LT-KB|DYNAMIC BLOCKS
I'm looking to make a dynamic block that will either strech up or down but some of the element stay the same in the other visivility
Here is a block i am talking about!
dynamic block.dwg
I have a dynamic block (attached) for our single line schematics. It works great, but there's a piece missing. The text in the file (In / Out) I would like to have insert with the block, but it needs to be editable, so it can't really be PART of the block... if that makes sense.
If at all possible, I'd like to have the text array down when you stretch the block...
I have a problem with dynamic blocks.
I have inserted a dynamic block (with .NET) and changed the value of a dynamic parameter (Linear). The block is stretched as it should be. (no problems here).
After a fiew other routines, I select the block again (by using its objectID) and a want to get the coördinates of the grip of the linear dynamic paramter. Is there a way to get the coördinates based on the linear dynamic parameter and its grip points? code in vb.Net?
I know that stretch will not affect major or minor radius of an ellipse in dynamic block.
What I would like to be able to do is use properties of an ellipse and some kind of parameter to be able to affect values in properties.
I know how to get ellipse radii data out of a block, but I simply cannot find a way to get them back in...
Is there a way to link field data back to block...?
I'm attempting to use Excel to take data from a drawing and give me purchase and cut lists.
I have successfully pulled the overall measurement from my dwg, and inserted it into a workbook. What I'd like to do now is to have a count of how many times the array function went into effect. For example, attached is a file containing a block called platform. When stretched, it inserts toggles every 2'. When I export the information from my dwg, I'd like for the program to not only extract the length, but how many toggles were inserted for each platform.
Am I missing something or is there no way to control array action spacing with formulas or user parameters?
View 3 Replies View RelatedI'm trying to create a dynamic block for a schedule to satisfy an engineer's request. The intent is to insert this block with the text for the schedule, then array the rows for as many fixture type as we may need. Then copy the text down and edit as needed.
I've got the array set up, but when I drag the array, the first array increment shows up, but the row of the schedule does not. It is not until partway through the second increment that the row shows up, but it appears with a gap between the first and second row, so something is wrong with the offset or origin... I'm not sure.
On another post, distance needing to be set in the Array Action Properties and not just under the parameter. I don't understand where this is.
In my Project I build a static Block by inserting dynamic blocks from a template dwg and then explode them.
Actually I create a new Data Base, insert the blocks from my template, set the according Dynamic Properties, Explode the Block in the temp DB and then wblockclone the resulting Objects in my destination BlockTableRecord.
This works fine, but:
in my source dyn. block there is an associative surface defined by a Polyline(Rectangle) , attached a stretch action to change the size. I can set the Width parameter, after the Explode the polyline itself is updated, but the planar surface is not... so if I explode this block I get a well stretched Polyline and the "base" surface.
Manipulating the dynamic Block works fine... If I have stretched 3D-Meshes, they are ok as well. It seems to be something with the planar surface object.
Dim objs As New DBObjectCollection idsToImport.Clear() If Helpers.Registry.GetValueFromRegistry("ExplodeSubs").ToString = "1" Then ' debug switch bref.Explode(objs) 'the dyn BlockRef in the external (temp) Database bref.Erase(True) For Each [code].......
I have drawn a simple block that I want to stretch in two directions manually or from the properties palatte.
My block works fine once and then breaks down. Stretch the block in the 'Y' direction. Deselect the block. Stretch the block again and only the grip moves. Edit the block and close the block, the block resets.
I have a dynamic block for HSS column. Previously it was always 1"x1" and I would just scale it to the proper column size I needed. Ignoring the wall thickness.
But if there was an asymmetrical HSS (i.e. 4x6) the wall thicknesses and radii of corners would look funny.
So now I want one that has Stretch Actions to change the size of the column. I added a Stretch to one side, then the other with distance multiplier of -1. But as you can see on the attached, the Linear Parameter baseline doesn't stretch. I want to have the Parameter Distance the actual full width of the column so I can change the columns with the Properties Palette. Otherwise, I would just start the Parameter from the center of the column.
The classic example of this, is a plan view of a door which shows you the opening, the arc and the door. How can I put a stretch on the opening and the door with a link in between, so when you stretch one, the other stretches with the same value?
View 4 Replies View RelatedI am working in ACAD 2009, I want to create a dynamic block for signage acad 2009 stretch mass element in dynamic where I need to be able to stretch hatched object. Neither mass element nor hatch do not stretch with the dynamic block. I need to see the area in 2D (not just a line).
View 2 Replies View RelatedI'm trying to create a Dynamic Block of an 3/4" x 3/4" aluminium angle with holes:
Depending on the length the number of holes will vary.
The distance between each holes need to be somewhere between 8" and a maximum of 12".
The holes must be centered and start from 1 1/2" up to 2" from each ends.
Each distance must be not more precise then 1/16" (no rounded off dimensions)
I'd like to simply drag the handle of the linear parameters (No lookup or visibility for 2 hole, 3 holes, 4 holes etc.)
I have a block that when I extend it, a new 10' section is added. It will only add the 10' piece (array). What I am looking to do is find a way so that once I hit a total distance have it switch the part that it adds. So I have like a rail, I keep adding these 10' pieces and then once it hits 40' I want it to add the end piece which is different.
View 1 Replies View Related