AutoCAD Civil 3D :: Surface Transparency Does Not Work In 2013
Jun 22, 2012
this thread confirms that Autodesk broke the surface transparency functionality in 2013. I imagine by the lack of response to the original thread that this is either a little used or not well published feature....
[URL]
IDSP Premium 2014 (mainly Civil 3D 2014 UKIE SP1 & Infraworks with some limited 3ds Max Design)
Win 7 Pro x64, 256Gb SSD, 300Gb 15,000 rpm HDD
16Gb Ram Intel Xeon CPU E5-1607 0 @ 3.00GHz (4 CPUs), ~3.0GHz
NVIDIA Quadro 4000, Dual 27" Monitor, Dell T3600
View 9 Replies
ADVERTISEMENT
Nov 6, 2013
It appears color transparency for surface analysis is now broke in 2013. It used to work in 2011 because I use to bring in Lidar data and run elevation analysis over top of aerial photos. I never found any type of resolution. Is Autodesk aware and are they working on this?
This issue reminds me of the Point Cloud issue with Lidar data right after 2013 came out. It worked in 2011 just fine and then 2013 they broke it. After calls to autodesk support and thread exchanges plus several months of waiting, service pack 2 for 2013 fixed the lidar classification issue.
View 3 Replies
View Related
Apr 17, 2012
In the previous C3D 2012 version I was able to set surface transparency just setting it on a layer with defined transparency. Example: I set my "existing ground" surface to a created "EG" layer (example name) and set transparency layer to 50% (example, again) and it WORKS! My surface become transparent...
But now, in the C3D 2013, I can't get the same results... my surface is not getting transparent. I already tried to turn off/on hardware acceleration and adaptive degradation and show/hide transparency.
More details: I can get transparency on points, triangles, contours etc... but not on elevation, and this is my priority.
Autocad Civil 3D 2013 - Infrastructure Design Suite
Windows 7 64 i7 860 @2.80GHz 8GB Ram Quadro 2000D
View 9 Replies
View Related
Mar 6, 2012
I use RocTek for cut/fil calculations, but the program is old and basic, I'm trying to transition to Civil 3D 2012 right now. Typically I create "no work zones" around my building footprints, so that I can do a more detailed take-off in those areas for over-excavations and that sort of thing. Right now I'm using Civil 3D to create an existing surface, a proposed surface, and then a volume from between the two. I thought if I just traced my proposed contours over the existing within the building footprint that I would get what I was looking for. However, analysis of the cut/fill volume shows that there are still some changes being made around the edges of the building.
Is there a specific way to make a proposed surface, but leave parts of the existing surface untouched?
See attached photo. The upper middle portion of the screen is where the building is (forgot to turn on layer).
View 2 Replies
View Related
Oct 25, 2013
I recently upgraded to Civil 3D 2013 and now all of my "Create Surface" commands do not work. I get the message " _AeccCreateSurfaceGridFromDEM Unknown command "AECCCREATESURFACEGRIDFROMDEM".
View 2 Replies
View Related
Mar 20, 2013
You can copy both the surface and the original (in this case contour polylines) data or only the surface. In both cases paste operation results into a copy of both data and surface.
Ok, But when paste and rebuild, the distance from original base point and destination point is applied in turn to the surface itself. Maybe it is a BUG ?
Civil 3D (2013)
View 2 Replies
View Related
May 17, 2012
Whenever I try to do a COPYBASE on a surface, C3D 2013 crashes. I can do the same steps in 2012 with no problem, but in 2013 I get a fatal error everytime.
Infrastructure Design Suite Premium 2014
Civil 3D 2014 x64
Windows 7 64-bit
6GB RAM
View 9 Replies
View Related
Apr 19, 2012
Attached is a dwg file that refuses to complete the surface triangulation. Can some try this? The maximum triangle length is set to off. I'm out of guesses. If I move the furthest point around it will complete the surface but just not in it's current location. Point number 69
View 9 Replies
View Related
Aug 29, 2012
Is it possible to data shortcut a surface from c3d2013 into c3d2012?
I tryed it and it says that the surface is in the drawing but its not showing up.
I've tried changing the style and the layer but nothing works.
View 1 Replies
View Related
May 4, 2012
C3D 2013. 64 bit. Windows 7.
Question 1.In C3D 2013 is there a ceiling to the number of points allowable in a C3D surface? Is it 1.5 million?
Question 2. In C3D 2013, when creating a surface from Point Cloud data is there a maximum point count based on the answer to question 1 - or is a different point count limit applied?
View 5 Replies
View Related
Sep 9, 2013
I have designed a pipe network in Civil 3D 2013, first I created a rule set for both structures and pipes, then I created a parts list, next I built my network.
Where more than two pipes connected to one structure, I found 'applyrules' couldn't align everything appropriately, so I had to manually amend the levels in 3D to ensure the pipes connected correctly (soffit to soffit / top invert to top invert).
My problem is that after doing all this, the surface model has been amended! I have changed the reference surface in the network properties and in the vista. The rim height of my structures seems to have been adjusted in the most part but my pipes have not.
In areas where the surface has gone down, my minimum cover is violated. Is there a way to move the pipes back down to minimum cover, without using 'applyrules', as using that command would change the gradients to the minimum, some gradients have changed during my manual adjustments.
Furthermore, where the surface model has reduced in level significantly, my pipes are now above the surface and the manhole has stayed there too.
View 1 Replies
View Related
Sep 9, 2013
I keep running into a situation where I would like to be able to create an edge or a work axis at the intersection of a work plane and the surface of the part. I figured out a work around if the surface is flat, but I haven't figured out a work around for a curved surface.
How do I create work axis where work plane intersects curved surface?
Or put another way: How do I project intersection of work plane and curved surface onto the work plane in a 2D sketch?
I need to be able to draw a 2D sketch on the work plane, but get a perfectly matching projected line onto the work plane, from the curved surface, at the intersection of the curved surface and the work plane.
The attached jpg shows the intersection in question. I circled it.
View 5 Replies
View Related
Jun 26, 2013
I'm trying to build a list of surface lable style, (both slope and spot elevation) using vlisp 2013.
I can create a list of the parant, but I can not find the clildren.
my goal is to change a surface label style between the parent and the children, using a list. To many style for the property menu.
View 3 Replies
View Related
Mar 11, 2013
with the Genio Exporter. I need to export the surface triangles from my job, but the Genio export dialouge box only gives me the option to export suface boundaries.
View 4 Replies
View Related
Nov 14, 2012
I am having some issues with surface profiles on a dreffed alignment no updating dynamically.
Currently it requires me to set them to static, then back to dynamic and they update.
I am well aware of the issue of dreffed surface profiles staying static. I am using the work around of dreffing in the surface and sampling in the drawing using the dreffed alignment.
Civil 3D 2014 (SP1)
Win 7 Pro x64
DELL Precision Workstation T3500
Intel Xeon 3.3GHz (w3680)
24Gb Ram
NVIDIA Quadro 2000 (1GB)
View 1 Replies
View Related
Dec 2, 2011
I often have to do storm pond surfaces that (for the purposes of planning) are flat on the bottom. These surfaces are created from a combination of survey data and grading groups and the tin of these surfaces is perfectably acceptable. However, when contours are shown, the flat bottom is shown with contours jig-jagging all over the place.
The attached image shows a comparison of the same pond. The top was created with survey data and grading groups; the bottom was created using contour data only. The generated surface on the top shows the bottom contour going in different directions and has parts where the an expected contour is missing.
How to correct/manipulate the surface to show a proper flat surface?
View 6 Replies
View Related
Oct 22, 2012
Has instances where you set your tolerance for the maximum triangle lenth to say 50m to reduce the amount of triangles along the edge that run at long distances. When I do this I end up with multiple surface holes and I'm not sure why as there are points in the area.
I thought well maybe it's because i should've reduced my max triangles first then added breaklines. Would this matter? I also thought I could add a line to the surface to fix the holes vs. deleting surface lines along the entire edge of a surface for many many miles.
View 9 Replies
View Related
Nov 14, 2012
I am trying to add points into a surface. I have done this before without any problems, but now I am having issues.
When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.
I select the surface and use the 'edit surface command' in the ribbon, choosing add point.
When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!
View 5 Replies
View Related
Dec 10, 2012
My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.
Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.
What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?
how do I shrink labels? Where is it in the settings ; the Align folder had been check.
View 2 Replies
View Related
Oct 2, 2012
I am issues with DEM files that I am downloading from the USGS website.I download 24k, elevation for the area I need. I then choose staged 1 second, add a surface to a blank drawing, then upload the DEM files to the surface.
The surface imports correcty, but when I try to import points taken by a surveyor on the same drawing, they plot incorrectly.The DEM surface and the points from the surveyor do not correspond. Also, the DEM surface is in meters, not feet. I have tried changing drawing settings, datum types, coordinate types, etc.
View 9 Replies
View Related
Apr 4, 2012
Is there any way to change the referenced surface on a Surface Elevation Label. I can see the surface in the properties but cannot change it.
C3D 2011
View 1 Replies
View Related
Jul 29, 2013
I have a project involving 3 programs. I am creating a planned development in 3d to be 3d printed when finished. The project is a 5 acre tract containing 8 buildings. I have built the surface in C3D and each building in Revit. The buildings are not in the same Revit file. For my solid work, I will bring the files over into 3ds Max Design to section into smaller quadrants to build in the 3d printer.
The questions:
Would it be better to import the surface into Revit to merge surface and buildings together?
Would it be better to import the buildings into C3D to merge entities?
Would it be better to bring those entities into 3ds Max and then merge them into one? Will 3ds Max Design allow me to insert entities accurately in the environment?
View 6 Replies
View Related
Sep 15, 2013
I need to create a sub-set surface from my main surface. not sure what the vernacular is for a "subset surface" in c3d but i do have a feature line that bouinds the desired area, but that is as far as i can solve.
i did try creating a new surface - pasted the main surface in the edit definition, then deleted triangles until the boundary alighned wiht my featureline. This seemed to work, but when i view the properties of the smaller subset suface, it shows a mimum and maximum elevation that is incorrect.
View 3 Replies
View Related
Mar 1, 2013
Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.
View 9 Replies
View Related
Mar 26, 2012
all of a sudden whenever I run audit on my corridor file the surface definition becomes a snapshot. To add to the drama, the corridor surface will not paste into an empty surface. Why?
View 2 Replies
View Related
Apr 11, 2012
With a new HP T 7100 Plotter I can not plot bigger sizes than A0 with transparencies. Installed is the HP-GL2 and the PS Plotterdriver. I can plot from AutoCAD normal plans till a sizeformat of A0 with trasnsparencies, but with oversizes there is no plot. Plans without Transparencies can be plottet and I can plot from other programs all plans even with Transparencies. As a landscape architect I want to use the transparency on bigger plans.
View 4 Replies
View Related
Feb 7, 2013
My problem added with pic ... I want to make volume calculate for sample road project. When I try to compute materials I cant use Corridor surface for DATUM... There is only target surface on option..
View 2 Replies
View Related
Mar 6, 2012
I am trying to visualize a road project. The problems is, whenever the corridor surface goes below the EG surface (when the road is in cut) the EG surface is the only visible surface.
I sort of need to subtract the corridor surface from the EG surface, or merge the both surfaces into one.
View 3 Replies
View Related
May 3, 2013
I was wondering if there is an easy way to trim one surface to another. Right now, I have two slopes (3:1) that are perpendicular to each other. They meet at a corner and I have extended them past each other so that I could see the intersecting edge. Now I would like to trim them to each other like you would a polyline etc... but I am not sure how to do this.
If I select surf trim, it tells me they are the wrong object type, but they are tin surfaces?
View 5 Replies
View Related
Aug 1, 2013
How to delete a work surface. These work surfaces were imported from an iges file which contains thousands of work surfaces. They are not associated with a part feature which can be deleted. I've developed a routine to sort through these and identify unwanted work surfaces based on their positions. The best I've been able to come up with is to make them invisible, but I'd really like to delete them completely to clean up the file. I did try to loop through and delete any surface body objects associated with the work surface but that failed.
View 8 Replies
View Related
Aug 15, 2012
I find myself creating new layers and making them slightly transparent all the time. But when I do this using Gimp it does not work right? This is what I am doing:
Add new layer
use transparency/opaque slider to change the setting
what happens is that the new layer stays solid until it goes below 50% on the slider and then it disappears, above 50% and it is back. It is like the 50% mark is an on/off switch for the layer.
View 6 Replies
View Related
