I just changed my startup setting from 0 to 2 because I do not ever need a blank "Drawing 1" to work off of. Now I am wondering if that screwed something up because when I boot up AutoCAD and immediately try to open a Sheet Set, I receive the attached messages and then AutoCAD crashes. Is this a bug that needs to be fixed?
View 4 Replies
I am getting a error when I open a specific drawing
FATAL ERROR: unhandled e06d7363h Exception at fel14940.
I have tried to recover the drawing (message says error were found and then I get the same error)
tried the back up file ...no go
tried a back up file from 2 weeks prior, same result.
Have tried inserting as a block to a new drawing... same error.
I have started receiving the following error:
FATAL ERROR: Unhandled Access Violation Reading 0x0008 exception at 1286aebh
I had been getting fatal errors on opening the program with the very same message. That has since passed but now it is happening when I try and open ADCENTER either at the command line or the ribbon button.
Map3D 2012
Intel Core2 Duo
2.66ghz
3gb ram
When AutoCAD is closed and I try to open a drawing from the Windows Explorer I get a fatal error and when AutoCAD is opened before opening the file from Windows Explorer everything works fine. We have this problem with several stations at our office.
View 4 Replies View RelatedI've been getting this fatal error message upon opening files.
It seems to be as I try to load x-ref's.
using autoCAD 2009 everytime I open up the Layer Properties Manager, it causes a Fatal Error and autoCAD to shut down, this is a first and need need to know how to solve this problem or at least a diagnose.
View 1 Replies View RelatedEven though I run the Dwgconvert function in DwgTrueview 2012 I still can not open the converted file in AutoCAD Mechanical 2012 SP 2. Fatal error with some hex memory addresses displayed. DwgTrueview opens and displays the dwg. just fine. AutoCAD R14 & 2000 open the file with no problem as well.
View 3 Replies View RelatedEnvironment:
Files stored using SAMBA shares NetgearReady NAS
Two sites connected via WAN
Users using Windows 7 -64bit with Architecture 2014
Mapped drives are used for both site to access NAS, but use different drive letters.
At one point working the projects, users starting getting fatal errors opening from the share. All attempts to get past this failed and I thought the drawing or base files were corrrupt. However, when the files are moved locally to workstation and opened without issue. The users in one office are now working off this files using UNC \serverproject...
The interesting thing, is that users in the other office have no issues dealing with these drawings using on the NAS. The only difference is the WAN and drive mapping letter. This is how they have always worked and never had this issue. The only other thing I will add is they upgraded from 2010 two months ago, but no problems with any other projects.
I keep getting the error message when I try to open this one project. Everyone else is getting the same message when opening it. It doesn't matter if it is a local file or a detached central file the same message comes up and closes Revit.
This is a 2011 Revit Architecture model but also crashes 2012.
I am currently using ACAD Civil 3D 2014. When I am in paper space and try to plot I get a Fatal Error before I even get to the plot menu. This is only happening in 2 specific drawings and I've done a purge, audit and drawing recovery. With 8GB of Ram there should be more then enough to at least plot a 5MB drawing.
View 4 Replies View RelatedSometimes 3D orbit works perfect, and sometimes it causes a fatal error before you even get started with it. I originally thought it was just large 3D objects causing it, but now I think it's just a 2014 issue...because I've had simple 3d surfaces (3d polyline with a surface) that have caused it to crash, yet have other larger surfaces that orbit without issue. I'm mostly using it to compare 3D polylines to surfaces, usually on as built alignments that we're working on.
View 9 Replies View RelatedI'm working in Civil 3D 2013 and am attempting to bring in notes and blocks from a .dwt, using DesignCenter. As soon as I drag a block into my current drawing I receive a fatal error message and Civil 3D closes. I do get the option to save a recover file.
View 8 Replies View RelatedWe are having trouble with one of our C3D 2013 seats crashing (giving a fatal error) when trying to edit or do anything with a pipe network. The drawings work fine on other computers. I am trying to keep from having to remove and reinstall the software.
View 5 Replies View RelatedWhen you start move after hover on a grip point which created by GripDataCollection.Add(myGripData) in GetGripPoints(Entity entity, GripDataCollection grips, ...) appears Fatal Error: Unhandled e0434353h Exception at fdbebccdh.
I try Overrule GripPoints for Alignment. For FeatureLine it works.
Possible, the reason is that Alignment is AlignmentEntityCollection and different approach is required.
public class GripVectorOverrule : GripOverrule {
// A static pointer to our overrule instance
static public GripVectorOverrule theOverrule = new GripVectorOverrule();
public override void GetGripPoints(Entity entity,
GripDataCollection grips,
[Code] .....
I am having an impossible time smoothing a surface created from feature lines in the attached file. I can smooth the service in parts except for the area that I’ve hatched – as soon as I try to smooth that area the drawing freezes or I get a fatal error. Ideally I’d like this surface to smooth to a 3x3 grid.
The things I’ve tried:
- Exploding the feature lines to 3d polys and recreating them as feature lines before adding them back to the surface.
- Copying the feature lines to a new drawing and creating a new surface
- Completely deleting the feature lines and manually re-drawing them from scratch before adding them to a new surface.
- Adding the feature lines with different supplemental distance and mid-ordinate distances (typically I do 2’ and 0.01’ respectively)
- Smoothing the surface in sections instead of one global smoothing of the entire surface (it always fails when I get to the hatched area)
- Smoothing the surface with different grid dimensions.
- Emailing the drawing to coworkers to see if they can create the surface and smooth it on their computers
- Combinations of all of the above.
64-bit HP Desktop - HP Z420
Intel Xeon CPU E5-1620 0 @ 3.60 GHz
24GB RAM
AMD Radeon HD 6570
Windows 7 SP1
I get a fatal error message: Unhandled Access Violation Reading 0x7ffffffd Exception at 6d9cc265h when i try to do anything in a drawing.
View 4 Replies View RelatedI have a Win7 X64 PC running C3D 2103. I recelty installed this for the first time and am seeing the following error message when I launch the application.
I've tried to do a repair and still get the message.
Received this error upon opening a drawing in Civil 3D 2013? I was working on it yesterday, tried to open it today, and it wont open. Recover wont work, and I also went through all the xref's and data reference files and did a purge, -purge, and audit. Only one of about 8 files had 7 errors. I am very good with doing purge and audits throughout the day so my files are usually pretty darn clean.
In addition, the .bak file is also corrupt, and the stupid auto save didnt work. I have it set to auto save every 10 mins, but for some reason it never wants to work. I had the drawing open for over an hour without a single auto save.
I have downloaded ArcGrid (ADF) files from the USGS and am trying to define a TIN surface in Civil 3D with those files. I have done this in the past without difficulty but now I get a fatal error and the system crashes in the middle of the process. The ADF files are large, approximately 465 meg, and cover an entire USGS quad area. Is there any tricks or sollutions that would allow me to use this data source to create surfaces without my system crashing?
The system I am using is a Dell Intel Xeon CPU, W365@3.20GHz with 24 GB RAM, 64 Bit OS.
When I try to create a survey database I get FATAL ERROR: Unhandled e0434352h Exception at fe139e5dh.
I have repairing both AutoCAD and .Net 4, I also did a regedit on the CommunicationCenter.
AutoCAD Civil 3D 2012 SP4
Windows 7 (64)
Every time i switch to Paper Space I get a Fatal Error in Civil 3D 2013. What could be casing the crash? It does it in every drawing so it does not appear to be specific to any one perticular drawing.
Civil 3D 2013
When I try to paste in any collection of cells from excel using "paste special" C3D crashes. I'm using 2010. It crashes trying to paste into any drawing, and any group of cells.
My error is:
Unhandled Access Violation Reading 0x209519f8 exception at 478f56h
Windows 7 64bit running Civil 3D 2013 with service pack 2 installed.
The system runs fine while on the network, but once the user takes it off the network and home or basically off the network it comes up with a FATAL ERROR when the program is started up.
Error is:
Could not load file or assembly MapPublishlmp.dll or one of its dependencies. The network path was not found.
I can ignore the error screen and "work" in C3D fine; just as long as i don't hit the <Continue> button or "X" in upper right hand corner. If either is selected the program bombs out and generates error report.
Have tried to create a shortcut with new profile, but it did NOT work either.
Like i mentioned - systems works find on network but once it is not connected to the network some issue is happening with the dll file for the mappublishlmp.dll
What ever the hell that is...Not doing ANY GIS work with system. NEVER published ANY drawings where this would have come into the mix.
We have a computer here that won't open drawings. This is the error he gets: FATAL ERROR: Unhandled e0434352h Exception at fcc8940dh. If anybody else tries to open these drawings they open fine. We have tried to open it with Civil 3d 2013 and 2014 but it happens with both programs. We have tried to recover and run audits but it still has problems.
View 1 Replies View RelatedI have C3D2009 with service packs 1,2 and 3 installed in my computer with Windows XP operating system.
I am having fatal error when I try to export a dwg file to 2007 DXF file. I receive the following message:
" Fatal Error: Unhandled Access violation reading Oxfcf064fd Exception at fcf064fdh"
Attached, please find the dwg file I am trying to convert to 2007 DXf file.
I have a plugin that creates cogo points, and for some users it seems to crash every time, but for others it works just fine (as for myself, I have zero problems with it). The subroutine is simple:
Using civLock As DocumentLock = acadDoc.LockDocument
Using trans As Transaction = db.TransactionManager.StartTransaction()
Try
Dim Location As New Point3d(PointX, PointY, PointZ)
Dim CogoPoints As CogoPointCollection = civilDoc.CogoPoints
[Code] .....
The fatal error occurs when the point is added, prior to the attempt to assign a raw description. What is boggling me is that, like I said, it works flawlessly for me (and others) but not at all for some users.
CAD crashes and I am getting the above error while trying to edit an existing corridor. I am trying to add two different regions in an existing corridor. I accomplished this task yesterday, but due to design contraints have had to add two more regions. The two assemblies that I am using are already included in the corridor, so I know it shouldn't have anything to do with the assembly.
AutoCAD 2010 C3D
I have some files that are difficult to work with. Every time I try to change the annotation scale of an existing viewport or create a new viewport and set the annotation scale equal to something other than the default 1"=40' the file fatal errors on me.
Oh, Im on Windows XP 64 (8gb Ram and a Xeon) running C3D 2011 (all service packs and updates applied).
I often have the need to change the orientation of my vieports to better fit my project.
I often, and I mean 9/10 times get one or more fata errors when try to do so.
For clarification I am grabbing the wheel in the top right corner between N and E and rotating the view. When I release the drawing is not in view. Then the program crashes.
It is very frustrating and adding hour on to my day.
CPU: (Brand NEW)
MSI GT70
Intel Core i7-3610QM
NVIDIA Geforce GTX 670M/3G GDDR5
12 (+4) GB of RAM
I know I am not running a quadro but I should still be able to handle this type of task.
Having a problem with AutoCAD Civil 3D 2012 which keeps crashing with a fatal error on a Win7 Pro (64) machine. Was able to get the user to make a screenshot on the most recent occasion, and the error was as follows:
FATAL ERROR: Unhandled Access Violation Reading 0x0014 Exception at f5a69bb9h.
Having looked through your forums I see that this may be related to the video card, which is a Nvida Quadro 5000. I've already updated the driver to the Quadro Performance Driver, v320.78, but the problem continues.
Is there a different partner certified driver that I should be using (can't seem to find any for Civil 3D) , or is the issue related to something else?
We just installed 2014 on two work stations and saved a few Civil 3D files with it. When we try to open these Civil 3D drawings in 2013 they crash with a FATAL ERROR.
The last few lines on the command line shows: Loading Modeler DLLs.
Modeling Operation Error: Operation unsuccessful.
Modeling Operation Error: Operation unsuccessful.
This error seems to only happen with drawings that have infill grading. I tested it with a drawing with just poly lines and it worked fine. I then converted those poly lines into feature lines using 2014 and it opened fine in 2013. I then added an infill to the feature line region in 2014 and it crashes in 2013.
Civil 3D 2013
Windows 7 64-bit
Xeon W3550 3.07 GHz
Nvidia Quadro 4000
12.0 GB RAM