AutoCAD Civil 3D :: Calculating Slope Area
Sep 12, 2005How I can calculate my area for different slope regions?
View 7 Replies
ADVERTISEMENT
AutoCAD Civil 3D :: Spanning Pipe Labels Calculating Incorrect Slope
Oct 30, 2013I notice issues using spanning pipe labels for the first time recently after having used them for years. The slope calculated by the spanning pipe label is completely wrong. I've attached a picture in which Labeled two pipes connected by a null structure. The two labels on the bottom are the pipes labeled individually at 3.53% and 3.34%. When labeling them as a spanning pipe, if I choose the downstream pipe first and them the upstream pipe it shows me a slope of 0.48%. If I choose the upstream pipe first, then it gives me 2.88%. Either way it's wrong.
As I was writing this I decided to check and see if the pipes were flowing the same direction (Start to End or End to Start). Turns out they weren't. After flipping one of the pipes around so that they both are laid out in the same direction (Start to End from Upstream to Downstream) the label now reads 3.37%, which is correct.
Seems like an the label should honor the flow direction of the pipe, no matter if they have been laid out in opposite directions or not.
AutoCAD Civil 3D :: Calculating Average Parcel Area
May 16, 2013Any quick way of calculating average Parcel Area? I used to export to LandXML and do an area report in CSV. That doesn't seem to be working for me when I export out of C3D 2012.
The workaround I found was to select all the parcels in Prospector, copy to clip board, paste in excel, find and replace "_Sq. Ft._" with 0, then do the average.
AutoCad :: Calculating Area Of Floorplan
Nov 1, 2012Any good tips when it comes to calculating the area of a floor plan? You are supposed to start measuring from the outermost part of the walls, but when I do that I run into trouble with the porch on the bottom of the drawing and the room on top left.
The problems are basically that the porch is not supposed to be included in the total area, and in the room on the top I end up measuring a small area twice if I start my measuring from the outermost part of the walls. This is not very well explained but I've drawn two red lines on the drawing to try to show where the problem areas are.
AutoCad :: Calculating Area With 2010?
Jul 15, 2012When I am trying to calculate area, i got wrong answer. At very first i thought it calculates area with inches (iam in metric sys), but then i checked options and its answer should be in mm, but I am getting wrong answer. In my object (which is rectangular) there's many other things, like hatch, buildings and so on. Maybe this can abstract for direct answer, because when i draw just a simple square or rectangle.
View 9 Replies View RelatedAutoCad :: Calculating Total Area Of Windows
Oct 31, 2012I have a building like this and it has a lot of windows.
I know how to calculate an individual window area by using 'area' or 'ls' command. But this is just partial drawing and the whole building has hundreds of windows and it will take forever to calculate one by one and add them together to get the total area. Is there any way to get the whole area easily?
windows are just rectangles (and solid hatch inside the rectangle).
AutoCAD Inventor :: Calculating Surface Area For IParts
Sep 12, 2009I want to calculate aurface area of iparts automatically. there are about 100 ipatrs and i want to find surface area of each ipart. is there any way that i just click the desired surface and its area is written in some file so that i can just go to the next ipart click the desired surface and its area is written automatically on some file.
Is there some option in inventor to define macro for it coz i hav no knowledge of defining macros.
AutoCAD 2013 :: Calculating Three-dimensional Surface Area?
Nov 11, 2012How to calculate the three-dimensional surface area of a revolved arch (such as attached file) by autocad 2007? such as an irregular dome.
Which software can do the job? Autocad or Matlab software or .....
AutoCad :: How To Draw PI That Used In Calculating Area Circumference Of A Circle
May 30, 2011How to drawing a Pi that used in calculating area, circumference of a circle, in AutoCAD as a technical drawing?
Is there available any book I could find some info regarding Pi in technical drawing?
AutoCAD Civil 3D :: Profile Geometry Editor - Slope-Slope Intercept To Place PVI
Aug 20, 2012Can you not perform a slope-slope intercept to place a PVI? Essentially holding the sta and elev of the PVI's directly before and after the PVI of interest and changing the grade in and out so that the sta and elev of the PVI of interest are changed.
View 2 Replies View RelatedAutoCAD Civil 3D :: How To Match Gutter Slope To Outside Lane Super Subassembly Slope
Mar 22, 2011Can't figure out how to match gutter slope to outside lane super subassembly slope. Have super eop targeting a feature line with elevations, but when i check section editor gutter slope doesn't match pavement slope.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
AutoCAD Civil 3D :: Shoulder Subassembly That Varies Slope In Relation To Lane Superelevation Slope
Jan 22, 2013i need a shoulder subassembly that varies slope in relation to the lane superelevation slope. i know that i can get a subassembly for the shoulder that will follow the alignment superelevation xml data but in my case i can't use it because we are just adding a shoulder to an existing road. we're not changing the superelevation of the existing road, just milling and overlaying and widening. right now i've created a profile of the outside edge of the shoulder that gives me the correct shoulder slope but whenever i change my centerline profile i have to redo the shoulder profiles which is a real time suck.
View 9 Replies View RelatedAutoCAD Civil 3D :: Slope To Depth Of 10 Feet Than Change To 2:1 Slope
Aug 13, 2012I am in the process of transitioning from land desktop to Civil 3D. I design roads in steep terrain and sometimes need to have my catch (daylight) slopes change. So my question is, how do I change a daylight slope at a specified depth? For example, from the shoulder of the road I want a 3:1 fill slope to a depth of 10 feet than change to a 2:1 slope until it catches the existing surface. Can this be built into a subassembly such that if the fill is less than 10 feet it will daylight correctly at a 3:1 and if the depth is greater than 10 feet then it carries the 3:1 for 10 vertical feet and then changes to the 2:1 until it daylights?
View 9 Replies View RelatedRevit :: Calculating Gross Wall Area
Aug 11, 2011How do I get Revit to schedule the gross exterior wall area? An isolated wall will schedule OK, but once you join it to another at a corner, the reported wall area doesn't match the exterior wall area.
View 5 Replies View RelatedRevit :: Calculating Gross Area Plans?
Aug 9, 2013Im using revit 2012.
I have an 11 floor building I wish to create a gross area schedule for. I have made all the area plans, and they all show up under the Gross Building Area Plans. But when i go to create a Gross Building Area Schedule it only lists 7 of the floors. (Leaves out sub base - Lvl2 and gives Lvl3-penthouse)
AutoCad 3D :: How To Fix / Distribute 40 X 40 Cm In Slope Area
Apr 5, 2012It's almost 2 days I cant imagine to distribute my boxes in a slope area.
see pix attached:
slope.jpgthe
yellow is the slope just see .
AutoCAD Civil 3D :: Calculating Cut And Fill?
Nov 20, 2013My background is actually in Microstation (mainly 2D). I was asked if I could calculate the cut and fill between two topo surfaces. Unfortunately, I don't have the files yet but I will eventually receive them. When I do, what would be the correct method to achieve this task?
View 3 Replies View RelatedAutoCAD Civil 3D :: Calculating Volumes Between 2 Elevations
Nov 20, 2013We have a good size channel and the section for the channel varies quite a bit. We want to find the volume excavated in the channel between 2 elevations (it is the area of sand per the goetech report)? A template was not used to create the channel surface, breaklines and gradings were used.
View 9 Replies View RelatedAutoCAD Civil 3D :: Calculating Volume From Corridor Models?
Sep 19, 2013I've been learning civil3d for some time now and I really want to understand how the program calculates volumes from road corridors.
When the top code is used to create surface from a road corridor, the created surface coincides with the top of the road pavement (binder/wearing course), which is not part of earthworks.
How can I create a surface at the formation level so as to compute actual earthworks?
AutoCAD Civil 3D :: Calculating Existing Berm Volumes?
Aug 12, 2013I am looking to calculate the volume of an existing berm from a TIN surface. I have read through some of the Civil 3D tutorials, and realize that I will need to have two surfaces (base and comparison), but need to figure out how to create the comparison surface.
View 9 Replies View RelatedAutoCAD Civil 3D :: Calculating Volumes With Out Of Date Surfaces
May 9, 2013I have been provided a file with a surface, however I have not been provided with the point files referenced to define the surface. As a result, when I try to calculate the quantities in the volume dashboard using a volume surface, I get the error that the surface is out of date. Is there a way to calculate volumes with an out of date surface?
I am trying to calculate the amount of material required to be cut when creating a flat bottom ditch.
AutoCAD Civil 3D :: Calculating Volume Using 2 Existing Surfaces?
Jun 9, 2013I have create my surfaces and now need a volume between to two surfaces. I created the surface by using the Surface/Create TIN Surface tool for both my OG and the surface after material has been imported. I have gone to the volume dashboard and it will not let me add existing surface. How do I calculate the volume?
View 3 Replies View RelatedAutoCAD Civil 3D :: Calculating Capacity Of Rectangular Pipe (not A Culvert)
May 7, 2013In Land Desktop using the Hydrology tools, we could get capacities for rectangular pipes based on slope, size, etc.
I have tried using the Hydraflow Express tools for this, but cannot figure out how to use them for a RECTANGULAR pipe (i.e. 10x4) box. Saw the circular option, but couldn't change where it says circular.
This is not a culvert analysis because we have inlets, multiple slopes, etc. It is part of an entire system.
I use these tools to layout the system before I want to put it into the analyses software we are using.
AutoCAD Civil 3D :: Area / Square Area In Closure Summary Of Mapcheck
Oct 23, 2012How to changes the settings for the "Square Area" in mapcheck's closure summary. When I right-click the dwg name in the Settings tab of Toolspace and choose Edit Drawing Settings, then Ambient Settings, I see the Area settings, but in the closure summary, there is also "Square Area". Why are these both there? It WOULD be nice to show sq. ft. as well as acres, but I can't find anywhere to edit it.
Civil 3D 2012
Windows 7 Enterprise SP1
Dell Precision T3400
(Q9550 @ 2.83 GHz)
8GB RAM
Nvidia Quadro GTX 650 Ti BOOST
AutoCAD Civil 3D :: Slope Map Display
Jul 1, 2013The undefined areas of a slope map now have a hatch to them and are plotting black. This map was created a month ago in 2012 without issues, upgraded to 2014 and now the undefined range has hatch!
View 8 Replies View RelatedAutoCAD Civil 3D :: Get The Slope At A Point (x And Y)?
Jan 2, 2012I have a TIN Surface, and I want to get the slope at a point (know X and Y).
Working Civil 3d 2010 and API.NET
AutoCAD Civil 3D :: Using Negative Cut Slope
Oct 30, 2012I have a simple driveway corridor along a steep hillside. For cut, I would like to have a negative slope away from the shoulder edge. I have tried numerous approaches and all 'cut' reverts to positive. I searched and found no clear answer. It's such a short driveway, I can 'fake' it in, but I would like to calculate quantities.
Using 2012 sp1, 64bit, windows 7
AutoCAD Civil 3D :: Can't Display More Than Two Slope Ranges
Jul 8, 2013I've got a surface that displays contours correctly. When I go to Surface Properties-Analysis tab, I can set an arbitrary number of ranges for contours, directions, elevations, slope arrows, etc, and they display correctly.
I can set an arbitrary number of ranges in the slope range box too, but when I click the Analyze button, Civil 3D 2014 hotfix 1 only displays two slope ranges: 0% to 2979736.0077% and 2979736.0077% to 99999900.0001%. (!)
AutoCAD Civil 3D :: Auto Slope Patterns?
Aug 10, 2013Can I automatically have my slope patterns introduced with a command like matchprop or something similar ?
I have 284 streets and it's getting ages to finish the slope patterns on every street. Civil Engineer / Infrastructure of metropolitan transports. URL....
AutoCAD Civil 3D :: How To Round Off Top Of Graded Slope
Mar 21, 2013I'm trying to match an existing slope design that has a soft rounded off top of slope. The toe (green) is a feature line and I'm using a 1-1/2:1 slope to natural surface grading rule. You can see the rounded contours in blue that I am trying to match.
View 7 Replies View RelatedAutoCAD Civil 3D :: Link Slope To Surface
Nov 7, 2012in my link "link slope to surface", i have the slope set to -2.00%. in the cross sections, it is at a +2.00%. why is this thing not linking at the defined -2%? see image.
View 1 Replies View Related
