AutoCAD Civil 3D :: 2D Solids Extracted From Surface Only Show Outline When Xreferenced

Mar 18, 2013

I created a surface with the style showing slopes as 2D solids.  I extracted the slopes from the surface and moved them to their own file.  They look fine in the file where they reside.  When I xreference them into a drawing, they no longer show up as solids.  They just show the outlines of the triangles.

I know I could change the style to to 2d hatches instead of solids, but I'm more curious as to why this is happening and how to fix the 2d solids.

Windows 7 64 bit
Civil 3D 2013

View 7 Replies


ADVERTISEMENT

AutoCAD Civil 3D :: How To Correct / Manipulate Surface To Show Proper Flat Surface

Dec 2, 2011

I often have to do storm pond surfaces that (for the purposes of planning) are flat on the bottom. These surfaces are created from a combination of survey data and grading groups and the tin of these surfaces is perfectably acceptable. However, when contours are shown, the flat bottom is shown with contours jig-jagging all over the place.

The attached image shows a comparison of the same pond. The top was created with survey data and grading groups; the bottom was created using contour data only. The generated surface on the top shows the bottom contour going in different directions and has parts where the an expected contour is missing.

How to correct/manipulate the surface to show a proper flat surface?

View 6 Replies View Related

AutoCAD Civil 3D :: Show Slope / Grade On Surface?

Jun 27, 2013

i was wondering is it possible  to show slopes  or grades on my surfaces  , or corridors  IN PLAN VIEW ?

View 8 Replies View Related

AutoCAD Civil 3D :: Show Hidden Surface In Profile?

Jun 15, 2012

I have modeled a storage pond on my site and  I have the existing surface hidden for the extent of the pond.

Is there a way to make that hidden existing surface, show up on the profile view?

I have attached images to better explain myself.

I am working in C3D 2012.

View 1 Replies View Related

AutoCAD Civil 3D :: Compute Materials Top Surface Will Not Show Up?

Jul 11, 2012

testing out using link to marked point and volumes i made a 1000' alignment, flat surface at 0, and put a generic lws 10' wide at 0% slope so i would know the real vol in my head to check. i omitted the lws link and then put a marked point at the center of the subassy and then put a linktomarked point and it put the link in ok as shown in the picture. the corridor made a top surface and if i make a vol surface all is correct.

but when i hit the comput materials > earthworks only the eg shows up.

the linktomarked point has top,datum codes by default.

View 2 Replies View Related

AutoCAD Civil 3D :: Create Surface From OG - Show Only Two Elevation Contours

Oct 1, 2013

I created a new surface, pasted my OG surface into it, set the build to exclude elevations less than and greater than but my surface still is showing every contour range. I want to only show contours at elevations of  371.5 and 370.5

Is it because it's a pasted surface?

View 6 Replies View Related

AutoCAD Civil 3D :: Can't Get Proposed Roadway Surface To Show Contours

Apr 12, 2012

attached is Roadway.dwg file

I made "Road" surface from Corridor Properties / Surfaces... but when I go to surface properties for "Road"...the statistics tab is blank.

2013 Civil 3D

View 2 Replies View Related

AutoCAD Inventor :: Converting Surface Into Solids?

Apr 2, 2012

I have several IGES files that I need to make into solid models.  I have been searching for days on how to do it in Inventor 2012 and everyone says how easy it is, but yet I have no luck. This file was created from a scanned mold and then made using a point cloud.

View 1 Replies View Related

AutoCAD 2010 :: Solids Only Show Up In 2D Wireframe

Apr 11, 2012

I'm using 2D wireframe as my default view while extruding some solid pipes. Everything appears to work fine, but when I switch to any other shademode eg. 3D wireframe, some of the pipes disappear. In Navisworks they show up as listed objects in the selection tree but cannot be displayed and more imporantly do not get considered in clash detection.

I can't see anything different about the properties of the "hidden" pipes over any others that can be seen.

If I slice the "hidden" solids, then one half or both halves become visible like a normal solid again.

I have hundreds of pipes to model and clash so need to resolve what's happening here. Attached is a small sample file.

View 2 Replies View Related

AutoCAD Civil 3D :: Create Volume Surface To Show Elevation Banding With Cut And Fill Ranges

Nov 12, 2013

I am working on a large park project.  I have a proposed and existing surface.  I have created a volume surface to show elevation banding with cut and fill ranges.  I need to create a drawing for someone who doesn't have civil 3d showing all the "cut" areas.  They really want a boundary of hatch.  What is the best way to do this after I change my analysis to -30 feet cut to 0 feet cut.

View 9 Replies View Related

AutoCAD Civil 3D :: Extracted Feature Lines From Custom Subassembly?

Mar 21, 2012

So simple little retaining wall subassembly created in the SAC. When i extract multiple feature lines from a corridor using this subassembly, all the feature lines assume the elevation of the first link i selected. So if i first click on 'RW_Hinge" all successive feature lines will show up with the same elevations as "RW_Hinge". if i erase all the feature lines the select a different link say "RW_Top" then they all go to "RW_Top".

View 7 Replies View Related

AutoCad :: Scaling Text In Xreferenced Drawing?

Jul 26, 2012

I'm currently using Autocad 2012, how I can scale a text in viewport whose drawing was referenced in the model view.

fyi the referenced drawing is a survey drawing.

View 4 Replies View Related

AutoCAD 2013 :: Xreferenced Colour(s) Displaying Wrong

Sep 15, 2012

I am editing a drawing i have inherited from the previous drafter who is no longer working here. this drawing references 2 other drawings. one is the title block, the other is the engineering drawing. both of these drawings have white objects in them, namely, some text and some solid hatching.

Instead ot those white objects appearing as white in this drawing, they are appearing as a grey colour. i have double and triple checked that these objects are coloured by layer and the layer is white in both of the xrefs. they appear white in the xrefs but not in the final drawing.

since we are using colour dependent line weights in our printing, i would like to get this colour problem sorted.

View 7 Replies View Related

AutoCAD Civil 3D :: Converting Corridors To Solids?

Dec 13, 2013

I am trying to convert my corridors to solids and under toolspace-settings-corridor-commands there is a command called export corridor to solid but this option is not coming up in my toolspace.

I made this original file in civil 3d 2013 but am working on in in civil 3d 2014

View 2 Replies View Related

AutoCAD Civil 3D :: Project Solids To Multiple Section Views

Jun 13, 2013

The new features in 2014 does not work. I can project solids to a section view but not to multiple section views.

View 1 Replies View Related

Photoshop :: How Do I Show Just The Outline Of A Shape?

Dec 14, 2007

I am trying to put a rounded rectangle around some text but it only makes a filled shape and covers the text. How do I put just the border of a rounded rectangle around some text?

View 5 Replies View Related

Photoshop :: Brush Outline Won't Show.

Jun 1, 2007

The outline of the brush won't show which really sucks because it would be nice to know how big the brush is going to be when you use it on your pictures and where exactly your pattern is going to be placed.

View 1 Replies View Related

AutoCAD Civil 3D :: Reduced Maximum Length For Surface Triangles Causes Surface Holes

Oct 22, 2012

Has instances where you set your tolerance for the maximum triangle lenth to say 50m to reduce the amount of triangles along the edge that run at long distances. When I do this I end up with multiple surface holes and I'm not sure why as there are points in the area.

I thought well maybe it's because i should've reduced my max triangles first then added breaklines. Would this matter? I also thought I could add a line to the surface to fix the holes vs. deleting surface lines along the entire edge of a surface for many many miles.

View 9 Replies View Related

AutoCAD Civil 3D :: Editing Existing Surface Using Edit Surface Command

Nov 14, 2012

I am trying to add points into a surface. I have done this before without any problems, but now I am having issues.

When I ID points which makes up the surface it gives me the correct Z level e.g. 24.5m, however when I hover over the surface it shows me the surface name and a different z level e.g. 0.65m. What is the reason for this difference in z levels? I think this may be causing the issue I am having when I add new points.

I select the surface and use the 'edit surface command' in the ribbon, choosing add point. 

When I add a point at the level I require(23.89m), it puts it in a lot higher than the surrounding area, so I tried to put the point in to the lower z levels (0.4m) it puts it in a lot lower!

View 5 Replies View Related

AutoCAD Civil 3D :: Volume Bounded By Existing Surface And Design Surface

Dec 10, 2012

My goal is coming up with the volume bounded by the design surface and the existing surface. I don't have the design surface modeled yet.

Do i need to create alignment offsets?. Alignment 1 profile view is also attached. Then Alignment2.

What about starting with alignment1 profile view? Since I have created a polyline as the design profile ?

how do I shrink labels? Where is it in the settings ; the Align folder had been check.

View 2 Replies View Related

AutoCAD Civil 3D :: Add A Surface To Blank Drawing / Then Upload DEM Files To Surface

Oct 2, 2012

I am issues with DEM files that I am downloading from the USGS website.I download 24k, elevation for the area I need. I then choose staged 1 second, add a surface to a blank drawing, then upload the DEM files to the surface.

The surface imports correcty, but when I try to import  points taken by a surveyor on the same drawing, they plot incorrectly.The DEM surface and the points from the surveyor do not correspond. Also, the DEM surface is in meters, not feet. I have tried changing drawing settings, datum types, coordinate types, etc.

View 9 Replies View Related

AutoCAD Civil 3D :: Change Reference Surface For Surface Elevation Label

Apr 4, 2012

Is there any way to change the referenced surface on a Surface Elevation Label. I can see the surface in the properties but cannot change it.

C3D 2011

View 1 Replies View Related

AutoCAD Civil 3D :: Import Surface Into Revit To Merge Surface And Buildings Together?

Jul 29, 2013

I have a project involving 3 programs. I am creating a planned development in 3d to be 3d printed when finished. The project is a 5 acre tract containing 8 buildings. I have built the surface in C3D and each building in Revit. The buildings are not in the same Revit file. For my solid work, I will bring the files over into 3ds Max Design to section into smaller quadrants to build in the 3d printer.

The questions:

Would it be better to import the surface into Revit to merge surface and buildings together?

Would it be better to import the buildings into C3D to merge entities?

Would it be better to bring those entities into 3ds Max and then merge them into one? Will 3ds Max Design allow me to insert entities accurately in the environment?

View 6 Replies View Related

AutoCAD Civil 3D :: Creating Subset Surface From Main Surface

Sep 15, 2013

I need to create a sub-set surface from my main surface. not sure what the vernacular is for a "subset surface" in c3d but i do have a feature line that bouinds the desired area, but that is as far as i can solve.

i did try creating a new surface - pasted the main surface in the edit definition, then deleted triangles until the boundary alighned wiht my featureline.  This seemed to work, but  when i view the properties of the smaller subset suface, it shows a mimum and maximum elevation that is incorrect.

View 3 Replies View Related

AutoCAD Civil 3D :: Create Cut Fill Surface From Existing Surface

Mar 1, 2013

Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.

The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.

I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.

1. Novapoint is quite unstable and crashes alot

2. You cant create profiles out of 3d faces

3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface

4. A large surface made out of 3d-faces demands alot of computer power 

So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.

View 9 Replies View Related

AutoCAD Civil 3D :: Corridor Surface Will Not Paste Into Empty Surface

Mar 26, 2012

all of a sudden whenever I run audit on my corridor file the surface definition becomes a snapshot. To add to the drama, the corridor surface will not paste into an empty surface. Why?

View 2 Replies View Related

AutoCAD Civil 3D :: Can't Use The Corridor Surface As DATUM Surface

Feb 7, 2013

My problem added with pic ... I want to make volume calculate for sample road project. When I try to  compute materials I cant use Corridor surface for DATUM... There is only target surface on option..

View 2 Replies View Related

AutoCAD Civil 3D :: Adding Corridor Surface To EG Surface

Mar 6, 2012

I am trying to visualize a road project. The problems is, whenever the corridor surface goes below the EG surface (when the road is in cut) the EG surface is the only visible surface.

I sort of need to subtract the corridor surface from the EG surface, or merge the both surfaces into one.

View 3 Replies View Related

Photoshop :: Windows In CS2 Doesn't Show Outline When Being Resized

Jun 26, 2013

When I resize the photo image, I loose the outline which matches the workspace color. How to I change the outline color?

View 19 Replies View Related

InDesign :: Show Text Box Frame Outline Like Older Versions

Feb 18, 2014

I just started using the new Indesign CC and one of the features that I miss is the blue outline that would appear around textboxes. It would allow me see where my text was and move it around. The new Indesign CC displays text, but with no outline around the text, which makes it difficult to re-adjust the box size and move around my text.
 
Is there a way to enable the text box outline to show when designing (not when printing) as the previous verisons of InDesign did?

View 2 Replies View Related

AutoCAD Civil 3D :: Trim Surface To Another Surface

May 3, 2013

I was wondering if there is an easy way to trim one surface to another.  Right now, I have two slopes (3:1) that are perpendicular to each other. They meet at a corner and I have extended them past each other so that I could see the intersecting edge.  Now I would like to trim them to each other like you would a polyline etc... but I am not sure how to do this.

If I select surf trim, it tells me they are the wrong object type, but they are tin surfaces?

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved