If you can see it in the image below, I am showing my minor grids with a dot linetype. I have a total of 6 profiles all of which appear to have the dots double up in random areas, they also print like this.
Civil 3D 2013
HP Z400 Workstation
6GB of RAM
296GB HDD
ATI FirePro V5700(FireGL)
Win 7 Home Professional
After upgrading from 2013 to 2014 we have a few drawings that had profiles created in 2013 and now when we open the drawing in 2014 the profile view disappears and so we regen and then we get a fatal error. I ran an audit and there are no errors, I re-sycronized the surfaces, i also ran an audit on all the xreferences.
View 1 Replies View RelatedWe are having an issue with profile grid shooting off to the left of 0+00 rather than starting at 0+00 and stopping at the end of the profile. There is nothing in the settings that I can find that is telling the grid to extend close to 2000' to the left. Three of the four profiles are doing this. One of them displays correctly, but there are no differences that we can find in the settings.
View 7 Replies View RelatedCan I turn off the begin and end vertical grid of a profile? Currently it can be turned off using the GRID AT VERTICAL MAJOR, even though I'm starting/ending my profile view at stations that are neither major (100') nor minor (50').
Civil 3D 2010.
I attached a pdf to show the vertical line at 19+90 that I want turned off.
Using part builder, I created a new pipe part for an odd-sized CMP arch pipe. In plan view, the pipe looks good. At first glance, I thought the pipe was drawn correctly in a profile view, but I realized that the pipe was displayed with the invert located at the wrong place in the profile view. I thought this was because the insertion point of the new pipe part that I had made was placed at the incorrect location in part builder.
So, I swapped out the incorrect pipe size for another one that I knew was correct, and then deleted the incorrect pipe from the pipe parts list, and went back to part builder, and placed the insertion point at the invert of the pipe; then saved the edited pipe part, ran partcatalogregen, added the "corrected" pipe part to the pipe parts list and swapped in the new corrected pipe size to the pipe network. However, the pipe still displays incorrrectly on the profile view.
The pipe data is correct in the pipe properties: the invert is stated to be located at elevation 20. The overall height of the pipe , 38" (3.1667') is correctly displayed on the profile view. But the actual location of the pipe invert is not shown at the correct location, elevation 20, on the profile view.
Im having an issue where the horizontal grid lines in my profile are projecting out past my last specified station (see attached) My profile begins at sta: 1+00 and ends at 1+12. My user specified station range is sta: 0+80 to 1+30. I didn't have this issue in release 11 (im currently using release 12) with this profile view style and i did hundreds of profiles with this very same style.
AutoCAD Civil3D R12 SP2
Windows 7 Pro 64 bit
Intel Core i7-2600 3.4GHz
8.0 GB RAM
Nvidia Quadro 600
So I have been getting a fatal error "INTERNAL ERROR: !dbobji.cpp@8743: eNotOpenForWrite" when I try to export to 2010 CAD.
I have worked out that it happens when pipes are displayed in the profile view.
I was working on some isometric drawings for my CAD class and I can't seem to figure out how to get the grid back to the standard 2D grid view that I used to get when opening CAD. I now jusr get this dotted grid every time:
[URL]...
I have created a pipe network and am now creating an alignment and profile from that network. I follow the steps outlined in help file and when I get to "Select profile view origin" C3D freezes. I can invoke the Task Manager and choose to end C3D, then cancel when prompted to save file and control is returned. But no profile is created. Is it a video card issue maybe?
Seems like it is creating the alignment but freezes before the profile is created - In Prospector there are aligments in the misc category from multiple tries but no profiles associated with them. When it occurs I can't zoom or pan in C3D but I can switch to another app.
Civil 3D 2013 SP 1, 64 bit
Dell Precision T5600, 16 GB
Win 7 Professional 64 bit
Intel Xeon @ 2.0 GHz
NVIDIA Quadro 4000
Any new methods for depicting flared end sections in profile views in Civil 3D 2013 or 2012? I just loaded Civil 3D 2013 last week and have been checking to see if flared end section depiction in profile views is any better than previous versions. I haven't noticed anything different. I'm I the only one wanting a easier way to depict flared end sections in profiles? In short, I have never been able to figure it out.
View 1 Replies View RelatedI tried moving a Profile View and even though I selected everything at once and selected a base point and destination point, the Profile View Station and Elevation labels moved with a different offset than the Profile View itself. ?
Civil 3D 2012
I want a grid where a grid line is drawn every 10mm, with division lines every 1mm.
When I set this up in illustrator the grid lines (major) render fine but I am not seeing any division (minor) lines at all. Is this the defauld behaviour in illustrator?
I'm working with a structure profile label style and it seems like the only way to anchor the position of the label is based on offsets from the structure itself... Any way to position the label based on the top of the profile view, so that I could make all of my labels horizontally aligned above the profile view?
View 9 Replies View RelatedI try to make curb return profile without profile view like a intersect command.
I was make curb return alignment but I can not find profile command without profile view.
I have a 10 foot profile view and a 15 foot manhole. I want to show the manhole but not the bottom 5 feet. It is extending beyond my profile view.
Civil 3D 2014 SP1
Windows 7 Professional
Intel Core Quad Q9650 3.0 GHz
8 GB, 64-bit
I have yet to produce a profile. I created a polyline and turned it into an alignment.
Looking at alignment Sample(3), I see that it is not superimposed over your surface. The polylines are, but the alignment is not. That will disallow creation of a surface profile.
Is the sample5 an alignment that sits on the surface? how come there is still no profile?
Attached are survey points that created the surface of a road embankment portion that caved-in. The road is very near a reservoir shoreline.
1. How can a surface profile be produce? I/'ve use line to change it into an alignement and then create a proile , then a profile view. But the the surface profile is missing.
2.the points having higher elevation are the top edge( road level) of the cave-n . A few few shots were take before the shorline elevations.
3. What the best way to come up with the rock volume to fill the cave-in given this surveying points., Also the shoreline elevation will be lowered some more while work is being done since the fill is not allowed to fall in the reservoir.
A tabular data sheet for profiles could be very interesting.
Civil 3D (2013)
I have an issue with a profile referenced into a plan sheet that is shifted when I view it in the plan sheet viewport. The profile stationing is correct in the profile dwg file and in the plan sheet dwg it is referenced into. But when I switch from model space to paper space in my layout sheet (the file the profile dwg is referenced into) the profile moves to the wrong station within my profile view in paper space.
The profile start station is 0+00, but it shifts to -1+00 within the viewport of my layout sheet.
The scales are the same between the dwg files (50) and the Annotation scale matches the dwg scales.
I am a C3D newbie who used ground survey points (Serrano_EG_surface) that generated a Civil 3D surface. The white line is consist of arc segments that I turned into polylines and then into individual CL alignments. The first alignment ,which has its left and right offsets do not generate the profile view that I needed to be created. There was a prompt asking for a profile to choose, but I don't know where in the drawing or in the propector panel to click on.
1. Are the ground survey points good enough so that any alignments over the those areas can provide me a surface profile, a design profile, cross sections every 50 feet, so that I can submit a preliminary drawing for environmental permitting. ?
2. When I check the object browser, the aligments preceding each other are not in the same elevation it seems. Do I have to to transform each of the polylines first into a 3d polyline and then an alignment so that I can create a profile.
3. Eventually , I wish to connect all these alignments to model a 1.5 mile rural road (more like an access road to a water reservoir).
4. What's a best techniques to keep track of modeling a road.This question pertains to e.g the object browser as one of the useful aid. I've also used the inquiry tool but not used it for its full potential.
When I open my profile file in civil 3d 2014 the grid disappears so I regenerate it and they are back. The problem I am having is when I run my cursor over the grid, it will give me a fatal error.
View 5 Replies View RelatedI am setting up plans and profiles for utilities. Most of the profiles are working fine. I have one that the horizontal grids stick out about 50 feet left of the profile view. why one is squirrely and the other are good.
I'm using C3D 2012 on 64 bit system.
I have the profiles grid to display as my company has displayed them for several years and it worked perfect in 2009. Then we switched to 2011 and now the grid is overlapping back on itself (see attached).
I am working with my reseller and I have done everything that I can think of to get this to not show with no luck. This needs to be fixed by Autodesk in my opinion since we pay for the product to work and it did before. This is apparently an issue in 2012 as well.
How to get it back to the way it was before?
I was wondering if after drawing an alignment, creating a profile, and profile view, is there a way I can mark items along the alignment so they could show up in the profile view. I am laying out a pipeline and want to have the profile display a marker for items such as tees, elbows, reducers and other items. The marker I would like to use will be something like the vertical style grade break markers.
Also on a side note, as each of these items will have a different name, is there a way that I can add these markers and then have each one with a unique name?
1. I had trouble with profile view of the alignment line shown. What step am i missing? Are there things that is turned off?
2. How can I best come up with the right volume to fill.
3. Do I need to learn the grading tools? or could i get buy with a section profile from the alignment. ( it is not even an alignment yet)
4. How to I render a rock fill in this cave-in.
The attached aerial image , has survey or cogo points that are imported to surface, to become surface points. . So I wanted to create a surface profile below and an outline of fill above it. Iideally the side profile would look like a trapezoid, where the base is the surface proile and top would be the design embankment.
But the reason , a surveying crew went down and took shots at the shoreline and a couple shots around the cave-in walls (higher elevation on the cave-in wall cannot be surveyed, although I coud have used a laser , did not) is so that a more accurate volume of the cave in can be obtained. I tried to label how far the road edge is from edge of the cave-in . Norice the higher elevations are the top edge around the cave in area.
The ouline for the embankment will be a mild slope then breaks to a more steep slope. like 4 :1 , then 1.5:1
I was given a horizontal centerline of a 5 mile bike path. We have to stake all the even stationing every 50 feet and all the VPC's and VPT's with vertical elevation. I have created the horizontal profile and also the vertical profile including all the vertical curve information. Is there an easy way to incorporate the elevation information back into the plan view so I can create points that carry x,y & z points that I can transfer out of autocad as a .txt file so we can upload it on our gps equipment?
View 9 Replies View Relatedthe vertical grid is not showing up even though is turned on in view style! tried different things but nothing seems to work, and the horizontal grid doesn't clip to the profile even though i select the option! it goes way up until profile frame!
Windows 7, intel I7, 8 MB RAM, civil3d 2013.
When I create a profile, then explode it, none of the text or lines are bylayer. My company wants everything to be bylayer. I can't figure out which style controls the profile to make everything bylayer after it is exploded.
View 2 Replies View RelatedIs there a way to easily add an object from a profile view to a plan view? I have developed a pipeline profile that has high and low points and I would like to show these points on the plan views.
View 9 Replies View RelatedI received a file from another office which had a split profile. The only issue that my project manager and I have with it is that the profile lines themselves run from station limit to station limit, and therefore the profile lines run through the vertical (elevation) numbers. Is there a way to adjust the vertical (elevation) grid marks to clean this up?
I've attached a picture of how it looks now.
Where the heck do I find the offset which controls the distance between the profile grid and my profile data band?
I have compared settings between ones that look the way I want and I'm just not seeing it.
(The attached doc shows you what I'm up to)