AutoCAD Architecture :: Determining The Drawing Units?

May 15, 2011

how do I go about determining the drawing units that are being used in a drawing? I want to be able to determine whether the units are set to feet, inches, millimetres, metres etc but can't fathom how to get this info using lisp.

View 2 Replies


ADVERTISEMENT

AutoCad :: Determining Scale Of Drawing

Feb 17, 2013

I need determining the scale of a drawing I got from the internet in ratio form. the drawing itself has a little scale bar in the corner, however, since i do not know the measurements of the actual structure i have no reference point and therefore cannot figure out the scale in ratios.

I read on here that you can use general reference point such as the average dimensions of a door/window ceiling etc. but the drawing is a longitudinal section of a church, namely, Temppeliaukio kirkko, which has no 'standard' dimensions.

I need this drawing in 1:100
longitudinal section.jpg

View 2 Replies View Related

AutoCad :: Publishing Drawings And Determining Which Space The Drawing Is In

Oct 4, 2011

I've got a persisitant problem with the publishing feature in autocad. I know how to set up bulk print of drawings using publish.

However the drawings are a mixed lot (some in paper some in layout). Is there a way to determine the state of the drawing without opening each one. In my case there is thousands of drawings and of course i do not have the manpower to inspect each one.

View 5 Replies View Related

AutoCad :: Determining Polar Coordinates On Hard Copy Drawing

Aug 19, 2012

I just started my CAD classes. I have been doing basic 2d drawing and just learning the commands etc.

My question concerns polar coordinates. I know how they work, but are you expected to be able to get polar coordinates off lets say a hard copy drawing with no annotations.

My homework so far has always had the length of the lines depicted on the drawing but not the angles. So if I was required to replicate a drawing that had no annotation is there any way other than guessing or whipping out my protractor.

This is just a nagging thought as I strive to understand CAD.

View 2 Replies View Related

AutoCAD Architecture :: Can't Adjust Units

Oct 14, 2013

I am using Autocad Architecture 2013. When I type in "units" and hit enter, two Chinese characters show up in the command line. If I continue to hit enter, it allows me to change some values but a dialogue box never displays. 

View 7 Replies View Related

AutoCAD Architecture :: Block Units Set To Mm - How To Change

Aug 14, 2012

I have revived an old project that was started about 2 years ago. I went to attach my title block in paper space and the drawing was itty bitty.

Seemed unusual because in another layout the title block is there with the same page setups etc.

Then I looked at the block units and they were set to mm.  Can it be changed?  If  so how?  Or am  I completely hooped?

ACA2011
Win7 64

View 1 Replies View Related

AutoCAD Architecture :: Units Keep Getting Set To INCHES Despite Default Being CM

Sep 9, 2013

I am working on AutoCAD 2014 and every time I receive and open a new file from our collaborators in Italy, the file units "turn into" inches.

This means that I have to go to Drawing Utilities, Change the units to cm, and then have to Scale everything so that the measurements make sense again.

I've gone into OPTIONS and have set CM as thed default measurements, but this problem persists. I know that the office in Italy can't possibly be working in inches, so I'm assuming there's something that's "lost in translation" when it comes to opening the file on my end.

View 3 Replies View Related

AutoCAD Architecture :: Setting Up Units In Project?

May 13, 2013

What is the correct procedure to set up units in a project. I want to work with meters, ant the metric template is in milimeters. if I change the mm in m, when I make views the callouts are displayed incorrectly. 

View 1 Replies View Related

AutoCAD Architecture :: How To Adjust Grid Scale To Be Same As Units

May 6, 2012

I just installed autocad architecture 2012. when i opened it to start creating a new drawing/project the unit of measurement was in Millimeters.. i needed the Unit of measurement to be in architectural units, so i used the units command to change it to architectural units. the problem i am having now is that i think the Grid Scale is still in MM. when i tried to draw a line on the grid the line appeared to be tiny. the length of the line was 36'-5". i adjusted the scale to 1/4"=1' but that didnt change anything. in order to see the line that i drew i have to zoom in so much..

How do i adjust the grid scale to be the same as the units?

View 1 Replies View Related

AutoCAD Architecture :: Property Data Sets In Wrong Units

Sep 2, 2013

I am using Autocad Architecture 2013 and I am having an issue with Property Set Data. Whenever I create door or window tags, the Property Set Data is in the wrong units.

I have two separate projects, on in Imperial units and another in Metric. When I add a new door/window tag, the units for that particular door or window are incorrect. The drawings are setup in the proper units, the dimensions are as well. But when I create these tags and subsequently the schedules for them, they are in the wrong units. The tags/schedules for the metric project are in feet and inches and the tags/schedules for the imperial project are in millimeters.

View 2 Replies View Related

AutoCAD Architecture :: Missing Units Files In 2011 Fundamentals Curriculum

May 24, 2011

Reviewing the ACA 2011 Curriculum for next year, I notice that Units 1 and 2 .dwg files are missing for the first two units. Is there a link to download the missing files?

View 3 Replies View Related

AutoCAD 2010 :: Drawing In Units

Jan 18, 2012

I had tried to draw in different units in autcad other than inches, but fail to find i way. I tried going on tutorials, but all they say was to type in:

"Type in Unit in command

Press enter

A option will pop up

Change Units to whichever.

Okay so I tried this, and I change it to feets. The problem is, that whenever i draw a line, it would always be in inches. I want to find a way to draw in feets, so how I can do this.

View 2 Replies View Related

AutoCAD LT :: Drawing Units Scale

Oct 12, 2011

I am experiencing with an old drawing I am trying to open.  The problem seems to lie in that there is a hidden scale factor being applied to the dimension.

I draw a line that is 1.27 long.  When I dimension the line the resulting value is .635.  I have double checked that my primary units are set to a scale factor of 1 and the problem still persists.  Even more strange is that if I set the primary unit scale to 1.5 the resulting dimension value is correct at 1.905, with primary scale of 2 the dimension is 2.54, etc.  I have used AutoCAD for many years and never run into this issue.I am dimensioning in the model space when this occurs and using AutoCAD LT 2012.

View 5 Replies View Related

AutoCad :: Drawing In Architectural Units

Jul 1, 2011

I am having problem getting my drawings to get small. Example 1" = 25' how is that translated into an architectural units. And the drawing to be small enough to fit in the screen. Actually I have problems with any architectural units to fit in my screen.

View 3 Replies View Related

AutoCad 2D :: Drawing Units Option Is Gone In 08?

Oct 10, 2012

I am familiarizing myself with the existing drawings here. I am working on version 08 (was previously on 07). I opened a dwg in 08 and received an error message "Newer AEC Object Detected" stating that some commands would not be available. With no other option I opened the drawing and discovered it was in metric. I went up to the Format tab as I normally would to change the Units to Architectual and discovered that there was no option to change the units. Even typing in Units in the command bar didnt do anything. It seems as if this drawing was originally created in 07 and now OPENS in 08 but you lose commands? It used to be that you couldnt even open something it was created in a older version, no? Luckily a PC in the office does have 07 and I was able to open it there to change the units over but I cant do this every time.

View 7 Replies View Related

AutoCad :: Drawing Units And Scale

Jan 7, 2013

I have drawn a couple of small buildings. I'm using meters and plotting to A3. For some reason the in the layouts I have to put in a scale of 15:1 and 8:1 to see the building when I print.

I have looked at some other buildings that people have drawn, they are of a similar size in real terms. However they are plotting to 1:25.

View 9 Replies View Related

AutoCad 2D :: How To Get A Drawing To The Right Scale And Units

Aug 16, 2013

I am using AutoCAD LT 2012. I am having a problem getting a drawing to be the proper scale and units. I pulled a drawing in and it has been drawn 1' = 1 unit. I really would like to get it so I can make 1 unit = 1". I need to preserve the current dimensions in the drawing.

View 5 Replies View Related

AutoCad :: Units - Are Interchangeable In Same Drawing

Nov 20, 2011

What if you are making a floor plan, and in that floor plan you are making a computer room that has two desks side by side (when put together) they measure 6' long.

Also, there's a simcard for the slim cell phone, on the desk.

How do you address this issue with respect to AutoCAD? Can you switch units mid stream?

View 9 Replies View Related

AutoCAD Civil 3D :: Scaling - Units In Drawing

Oct 16, 2012

I have a drawing that was given to me by an architect with a scale 1:250 (0.004 in viewport). The architect drew everything in millimeters and it's a Site Plan, why ? I do not know. The units in the drawing are decimal-millimeters.

The page set-up for layout 1 was for 24x36 drawing size (typ.)I know need to make a layout 2 for a sheet size 11x17 but I can not get my viewport to scale correctly. So, if a 24x36 sheet size had a VP with scale 0.004 (1:250) then what is the scale for a sheet size 11x17 ?

View 3 Replies View Related

AutoCad :: How To Scale A Drawing To Proper Units

Mar 6, 2012

what is the proper way to scale a drawing? The Lines that i have should be 3' ,not 3"

What is the correct way on to scale the drawing to the proper units?

View 3 Replies View Related

AutoCad :: Change Drawing Units To Millimeters

Nov 28, 2006

I have some drawings that are drawn in millimeters. I need to add to the drawings but when I type 36 I get a line 36" long. I need to change autocad so that when I type 36 it draws a line that is 36mm.

View 9 Replies View Related

AutoCad :: Setting Drawing Units Precision?

Sep 22, 2011

What system variable changes the Drawing Units Precision?

View 5 Replies View Related

AutoCAD Civil 3D :: Drawing Units Stuck On Architectural

Feb 22, 2012

I have an old dwg that I used to add new data to. I also inserted a block produced by Revit to get a building elevation. I am not sure when or how it happend, but my drawing scale units are stuck on arch. I am talking about the bottom right hand corner of the screen on the status bar where there is the spot to set drawing scale. When I open by clikcing the arrow all the scales are in architectural units. I can add a custom scale of 1"=100', but it does not otherwise appear in the list. I wasn't going to wrry about it, but when I layout a plan/pro series they do not seem to be scaling correctly (and I cannot find a place to specify what scale I want the views to be at). UNITS, -DWGUNITS & -AECDWGUNITS don't fix it, they are all set to decimal, etc. Using the seetings tab to change the drawing settings, everything is set to feet, there is no place to specify arch units, the 100 scale drawing is shown as a custom scale.

This is C3D release 2012, on a 64bit Win7 Pro machine, everything is up to date.

Where I can change the units for the drawing scale?

C3D 2012 on 64bit Win 7 all up to date
Dell Precision 7core 8GB RAM
NVIDIA Quadro FX 1800M
LDT/C3D user since release 12

View 2 Replies View Related

AutoCAD 2010 :: Drawing Units Imperial / Metric

Sep 13, 2013

We have some machines which seem to work in imperial maesurement a dn others which work in metric.  it is frustrating when trying to insert a map block that is metric and is inserting into a drawing which is set up as imperial.  We have tried using the - dwgunits to change to mm, and then using insunits , insunitsdef source and insunitsdeftarget to 0, this works when the PC is currentyl in use. when shut down and restarted it reverts back to imperial setting.

Am i right in thinking this is something that needs to be done at the software installation stage to make it default to metric everytime?

View 3 Replies View Related

AutoCAD 2010 :: Changing Units On A Existing Drawing

Apr 4, 2012

I have a venue drawing that is in mm and I need to convert it to ft/inch so I can update and get dimensions from it.  Can this be done so when I change the format in drawing units it will update the drawing units?

Current settings.
Drawing units
Length:
Type - Decimal
Percisin - 0

Angle:
Type - Decimal Degrees
Precision - 0
Insertion Scale:
Unitless

View 4 Replies View Related

AutoCad 2D :: Entering Imperial Units In Metric Drawing

Apr 15, 2011

AutoCAD 2010

Wondering if there's a way to enter imperial units in command line of a metric drawin and have it convert imperial to metric.

IE. I'm constantly taking field site dimensions in imperial and it'd be useful if i didn't have to do conversion every time.

View 8 Replies View Related

AutoCad :: Adjust Default Settings Of Drawing Units?

Apr 13, 2011

how to adjust the default settings of my drawing units. I have adjusted these so that if I create a new drawing they are set as I want them. But when I output a drawing from

I work with a land surveying package. I use both AutoCAD 2006 and R14. When I export a cad dwg from the survey software and open it in R14 my drawing units are as I want them E.G Direction Control = North = 270 and should be set to clockwise. If I open the same exported drawing but in 2006 the settings change. If I create a new drawing in 2006, the settings are as I want them.

View 3 Replies View Related

AutoCad :: Drawing Returned To Units To Change To Decimal

Mar 27, 2013

For an autocad assignment, we have been given a drawing in engineering notation (feet and inches) and have to draw it with SI units dimensions. Doing the drawing was fine, BUT, I drew it in inches and thought that I could change it to millimetres.

I have used the units command initially to set up engineering. Then after drawing returned to units to change to decimal. Dimensions turned out in inches regardless. I also tried the scale command to alter the scale, then dimension , still no luck. I went into the annotation menu got to modify primary units and alternate units and still no luck. Not even my tutorial teacher knows how to do this.

View 2 Replies View Related

AutoCAD 2010 :: Displaying Dual Units In A Drawing

Sep 18, 2012

I am displaying dual units in a drawing with primary units being Customary. The metric unit displayed is incorrect.

View 1 Replies View Related

AutoCAD 2010 :: Can Units Of Dimensions Be Changed In Different LAYERS In Same Drawing

Jul 10, 2012

Actually, i tried to mention dimensions in metres in first layer and the same dimensions in feet in different layer.

View 1 Replies View Related

AutoCAD Visual LISP / AutoLISP :: Toggle Drawing Units

Nov 28, 2013

Is there a way of opening existing cmds in the visual lisp editor and edit them to do something else? I'd like to set up a lisp where 'uu' would switch the drawing units from decimal to architectural units and hittng 'uu' again would switch it back.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved