I`ve a problem when i`m using the stretch commend, for istance to move the position of a wall opening done with a poliline and there`s a door or a window block within the stretch area, this object stays in the original position whereas the lines has already been streched. This makes that I`ve to move manually the block to the new position. Is there any way to stretch objects and blocks together?
View 8 RepliesI would like to find a way to give a maximum and minimum length to a stretch (or move) but without absolute values.
simplified example of my block:
I have 2 squares, of which one big on, and a smaller one within the bigger one. I want to be able to stretch both squared indefinatly (no problem there), but the big square may never become smaller than the small one, and the small one may never become bigger than the big one...
In other words: the inside square should always stay inside the bigger one, no matter the size of the squares.
The problem with this block is that I have a hatch pattern between the squares, and as soon as i stretch the small square outside (or equal) to the big square... the hatch pattern 'crashes'.
I need this block to do the following:
1. Move the right piece so it ends at 3', 4', & 5'.
2. the move right hook and 'backing' to stretch/copy (or array) so it adds a hook to the right and fills in the backing.
so this means that a 3' gets 4 hooks, 4' gets 5 hooks and 5' gets 6 hooks.
3. the block as shown is the smallest configuration with 3 hooks.
I could just set up a visibility and draw each one at it's appropriate length but I'm trying to keep this simple block to a min size. If all else fails, that's the route I'll take.
I've tried a couple different configurations and I keep getting duplicates or the end piece doesn't move the correct distance.
I'm trying combine a Move and Stretch Action such that the same handle MOVES the detail UP/DOWN and STRETCHes the detail RIGHT/LEFT while maintaining the base of the detail line at the reference line. Sounds confusing maybe but this is the most intuitive and elegant way to design it. However, I can't get it to work.
The attached detail achieves the same functionality but is a little clunky.
Any commands or 3rd party applications that would allow me to move or stretch objects that reside in an XREF?
The cherry on top would be the ability to do this to only specific layers.
Whenever I use the move command on a line or series of lines that are touching other lines, the lines that aren't part of my selection move with that one line. cad-movecommand.jpg Here's a series of screenshots showing what I mean. I can't move just that line without moving the other lines around it.
View 3 Replies View RelatedI've created a dynamic block with listed increments e.g. 36, 42, 48 inches width. The dynamic window block that comes with autocad has the same incremental stretch.
This block shows the tick marks as well as a the value in a dynamic input box. How can I have the value displayed in my custom dynamic block. All I have is the "tick" marks.
I have been working on a dynamic block that need to look like the attached jpg. Basically it needs to be able to stretch up to 50'-0" but in ten foot segments (part size limits) +/- an additional but in 1 foot increments.
I've got two blocks that will either array or stretch. But have not been able to get it to match the actual requirements. I have attached my current block attempt. Also as you can see from the jpg, the support posts usually alternate as well and I haven't figured that out yet either .
If you have a drawing open and the Tool Palette Architectural open click on the door. It has "tick marks" where you can stretch the doors opening to (24", 32"). I want to know how to add those "tick marks" to my blocks .
View 4 Replies View RelatedAttached is a block that I am using for Finish plans. Basically how it works is that it is suppose to be inserted and then stretched to indicate a finish change in the floor. When I insert it and stretch it, it works exactly as I want it, but when the scale is changed, the center tag resets to the original center before the block is stretched. I would like it to stay in the center relative to the line that is stretched.
Not sure if you understand, but if you are good with dynamic blocks. You will notice that the dot is annotative where as the line that stretchs is not. I cant have the line change because it will be stretched between two areas with different floor finishes and that will stay consistant. I want the block to adjust so that it is the same size on all the scales of the drawing.
When I move any object using move command then dimensions are move with objects but dimensions are stretch and show as long extension line in the drawing.
I have checked DIMASSOC it is set to 2.
When trying to stretch of move a line in AutoCAD using the grips, it will move additional lines that are touching. It does not do this for every line in the DWG. It seems to be random. They are not grouped. What could be the problem.
View 3 Replies View RelatedI have drawn a simple block that I want to stretch in two directions manually or from the properties palatte.
My block works fine once and then breaks down. Stretch the block in the 'Y' direction. Deselect the block. Stretch the block again and only the grip moves. Edit the block and close the block, the block resets.
if it's possible to link a rotation with a stretching action. I have a text (or an attribute) inside a box that can be stretched. But if the box becomes too small to hold the text horizontally, I would like that the text automatically rotate vertically without any other action that stretching the box. If that is possible, is it also possible that instead of a text, there's an attribute, and that it rotates according to the attribute's length ?
View 9 Replies View RelatedSee attached DWG. Two offset arrows.
This works as long as it is not rotated, but distorts if rotated and then stretched.
I'm using ACAD2006.
I created a dynamic block with a polar stretch. I insert the block, then have to select the grip to rotate/stretch it. Can it be inserted and then rotated/stretched all in one action? The insertion point is at one of the line and the polar stretch grip is at the other end.
View 3 Replies View RelatedI would like to stretch my extruded shelf using a list of value settings.
I completed the steps in block edit but it will only allow my object to move to my value sets.
In 2D I have no issue.
What am I missing when modifying 3D objects.
See attached blocks.
I have a linear stretch D1:
Distance Type: Increment
Dist Increment: 1
Dist Minimum: 1
Dist Maximum: unlimited
I also have a linear stretch D2:
Distance Type: Increment
Dist Increment: 1
Dist Minimum: 1
Dist Maximum: is it possible to set the maximum distance to equal D1-2.5??
Both linear stretch D1 and D2 can be stretched independently. So D1 may be stretched to 100, and D2 may be stretched to 50, but what I am trying to do is ensure that D2 will never stretch beyond the distance of D1.
My firm worked on a project recently with a sheet numbering system that created long sheet numbers, ie, MH-101-R1. Since the sheet numbers were so long, they no longer fit in our normal sheet/detail/drawing label blocks. (See attached DWG for an example.)
We are looking to create either a dynamic block or some kind of block that will automatically stretch with the text length.
I was wondering if it is possible to use dynamic blocks to stretch a rectangle evenly, using only 1 point? I have attached a PDF of a rectangle with 2 lines coming out of each side (before & after picture). I want to use dynamic blocks to pick a point at the top right of the block, so that when I pull it out, the lines will extend, but stay attached to the rectangle. I also what the rectangle to stay in the center at all times.
View 9 Replies View RelatedI have attached a drawing that I am trying to stretch two lines - one lengthen and one shorten as I rotate the connecting line.
View 4 Replies View RelatedSee the dwg attached.
I'd like to modify a dynamic door block I've created so that I can stretch by door leaf size OR structural opening size, but I'm not sure how to do this.
Incidentally, I think the block has some flaws:
- I think the 'center/flip point' is not exactly in the center!
- The frame size should be 40mm, not 32mm
- The packing zone should be 30mm, not 6.38mm!
I foolishly thought i'd sorted making hatch work within a dynamic block that requires user input to set length and width of block...the hatch would fill to the revised size when the user sets the length and width in the properties dialogue...woohoo. Off I go home from work having defeated the nemesis of the day.
Open up my drawing today and can I get the hatch to act as it did yesterday?
I built my block (a simple rectangle all told) added my parameters in block editor. length and width linear actions with 0 grips as I don't want stretching by grips. Added the stretch actions. Tested the block (without hatch)...working. Only then did I hatch, so into block editor and using associative, send to back, normal island detection and selecting the rectangle to hatch. tested block ...working. great. Inserted the block into new drawing...working.
Opened AutoCAD today...Not working...hatch remaining as original size
Tried building new block exactly as I did yesterday...no joy...
On a side note...it works if I leave grips on but only if I use the grips to activate the hatch (it still doesn't work by just typing into properties though) that's not going to cut it as I don't want to be telling everyone to wiggle the grips so to speak.
I use the right mouse click command as my enter. But for the past couple of days when I try to use the move, copy, stretch commands, everytime I go to select a base point - autocad selects the point and then automatically snaps or displaces to a random point off of the screen. I don't know if this has something to do with the right mouse click or not, but I can't figure out why it keeps snapping off screen. If I switch and use the enter key or space bar as enter the problem goes away.
examples:
Command: s STRETCH
Select objects to stretch by crossing-window or crossing-polygon...
Select objects: Specify opposite corner: 13 found
Select objects:
Specify base point or [Displacement] <Displacement>:
Specify displacement <0'-0", 0'-0", 0'-0">:
Command: m MOVE
Select objects: Specify opposite corner: 43 found
Select objects: Specify opposite corner: 27 found (14 duplicate), 56 total
Select objects: Specify opposite corner: 18 found (14 duplicate), 60 total
Select objects: Specify opposite corner: 14 found (4 duplicate), 70 total
Select objects:
Specify base point or [Displacement] <Displacement>:
Specify displacement <0'-0", 0'-0", 0'-0">:
I select my objects to move, then I select my Base Point to move my objects away from, then when I select my destination point the command changes the Base Point to the selected destination point and asks me again to select a destination point.
I have realized this problem occurs not only with the move command, but also the stretch command. Also, it does not matter if I am using command modifiers or not, the problem occurs regardless. Also, it does not matter how I hit enter using the command (keyboard enter button, space bar, or right mouse button) the problem occurs regardless, and occurs entirely AT RANDOM.
Following previous what I have attempted to resolve the problem:
- remove the AutoCAD LT 2012 from the computer entirely and re-install
- installed the latest LT 2012 Service Pack
- changed the mouse to a new, wired mouse (I was already using a wired mouse in the first place)
- change the keyboard (which I think is irrelevant since changing the mouse did not work either)
I am working on a dynamic bi-fold door block. I have added actions that adjust the two leaves of the door to correspond to different opening widths and allow the jamb width to be adjusted. I am now trying to add flip actions in both directions. There is a regular swing door block in the drawing and I want the bi-fold door to have basically the same functionality as the swing door does.
I can't seem to get the angled stretch actions required for adjusting the opening width to work after flipping. I have tried including the stretch actions in the selection set for the flip but it does not seem to work.
I try create simple block where I change dimensions of polylines. Everything work with stretch partameter until I try use search parameter for change dimension.
View 4 Replies View RelatedI'm trying to create a block for angled handicapped parking stalls.
I used an array chained to a stretch in order to increase the number of stalls. It worked but for some reason it does not work in all of my visibility states. In some visibility states the array and stretch do not stretch together. The block should end with a stall but some end with a line and no stalls above it.
I attached a drawing with the blocks. The block named "STALLS-60-HANDI" it works correctly except in visibility state 9' and in "STALLS-60-4space Handi" it only works in visibility state 10'.
rename to dwg . fire wall would let dwg posting
I cleaned up my block and I am trying to use a field to reference a polyline for it's overall distance. The distance changes with my lookup action. After rotating and going back and forth from "On" - "Off" - "Both Off", then back to "On", the red polyline doesn't stretch back on it's original plane.
View 5 Replies View RelatedI am trying to put a polar stretch on the block uploaded, but it doesn't seems to work (maybe because of my constraint? ). If something major is wrong with it, is there another way I can make the same drawing proportional when i rotate it and stretch it ? Also, after that I have to use it for vlisp.
View 5 Replies View RelatedI am trying to be able to have my outreach arm stretch horizontally and on angles of 5 / 10 / 15 degrees from the pole. I have been able to make the polar stretch for this and it works fine though what i am trying to do is have the luminaire height also stretch and move when the size of the outreach changes (i can make the linear dimension work the way i want though not the luminaire parameter) as when you add the paremter into the stretch action is only moves the top and leaves the bottom at the same location which is not giving me the correct height.
The block itself is alot more complicated then this I have stripped most of the parameters out to make it less confusing but the end result would allow the user to input the outreach angle, outreach length and luminaire height. I have attached drawing for your reference.