I was wondering if there is any way to detect and define edges of the slabs and also the opening within the slab, or if there is any way to automatically detect slab’s openings in Autodesk Revit (Structure, Architecture or MEP)
In other words what is important for me is to select boundary lines which shape the slab and openings (if there is any) not the mass.
I have an interior amphiteather with stepped concrete steps and a bottom lower slab, which are recessed and below the ground floor level of 0'-0".
Before adding the topography to the job, the steps layout and the lower salb showed on plan, but since adding the topography, the lower steps and the lower slab do not show. Cutting a section thru the amphiteather, the earth is seem to be above the lower steps and the lower slab.
How can I modify the earth in this interior area of thh building so the earth (and topography) is below the concrete steps and the lower slab? (so these recessed concrete floor elements could be seen in the plan of the building)
I'm trying to separate my ground floor slab into two different slabs each with a different stratigraphy of layers. How can I do this? I've edited the footprint so that it looks like there are two distinct floor boundaries but when I go to select the floor in order to edit the type, the entire floor, or both "pieces" get selected and I can't seem to just edit one piece...
View 1 Replies View RelatedI'm new to Revit. For instance I was working on adding foundation slabs to my walls .. all walls were done and had slabs beneath them and one wall still didn't have any. Once I tried to add the slab to that particular wall ( just by clicking on it, like ive done with every other wall ) it fails to do so and doesn't add any slab.
But my main problem is, sometimes when I work on my project everything becomes UNCLICKABLE, I do not know what im doing wrong and the only way for me to add walls or anything is by clicking CTRL+Z untill the meny gets highlighted again.
Ive put a screenshot in the folder.
What is a good way to finish up the monolithic stairs?
- How can I join the top tread to the upper floor slab? (red circle in attached sketch)
- And is there a way to join the CIP monolithic stairs to the CIP walls? (blue circles)
On using magic extractor - I need to make straight lines on my edit of a cupboard, Other than doing it free hand is there a way to do it using a ruler or some kind of measurements or straight lines ?
basically i need to cut out an image (cupboard) so it can be used for advertising purposes and i need clean lines at the bottom of the cupboard as there are shadows i need to edit out.
I created an underground parking level but for some reason, I can't create a Space for it even though it has walls, a ceiling, and a floor.
View 1 Replies View RelatedI'm trying to create an oval/circular shaped reception desk, which needs me to create a circular slab. It won't allow me to apply slab properties to circular objects, I have also tried creating a square slab, then cutting holes in it... but still, it won't let me use circular linework to cut holes in slabs. Drawing an oval using straight lines would be innacurate and too time consuming.
Any alternative methods of creating something oval that can represent the worktop of a reception desk, or perhaps knows how to create a circular slab?
I'm Create a Concept in 3d max mesh which is .
Now I want to make it into REvit.
Is there a way to remove the edges and is only a shell.
This and other elevations have lines between new and existing walls/soffits. Joining doesn't eliminate the line. The existing wall is also in a group.
Is there any way to selectively hide an edge in an elevation?
AutoCAD 2010
AutoCAD LT 2013
Revit Architecture LT 2013
In Revit LT 2014, I've tried unsuccessfully to override the color of topographic surface edges in my model to white, so the edges don't show up in plan views. I've tried through the Object Styles menu, Override Graphics In View By Element, and Override Objects In View By Category, but nothing has worked. These overrides have worked for me in the past in previous Revit Arch versions, so I don't know if LT just doesn't have that capability, or it's a bug.
I can't simply extend the topo surface past the view window edges (I only want to show contour lines on my site, since they've been surveyed, but the neighboring site has not been surveyed, so I don't want to guess at them). I really just want to hide the toposuface boundary edge.
I want to make my walls to be adjusted to the ceiling.
View 1 Replies View RelatedSelection layer edges of a particular wall,
It is really exhaustive when it comes to select an edge of a layer of a wall. For example, if we need to align a column in the wall in the correct space, we need to select the corresponding edge of layer of the wall (indicated in the screenshots below). It really takes time just to select this edge (hovering + TAB).
Software: AutoCAD 2014, AutoCAD C3D, AutoCAD M3D, Revit
Windows 7 (Ultimate 64 bits),
Firefox 20.0,
Kaspersky 2013.
The attachment below shows some of our thicker linestyles that we need for our life safety plans in the form of detail lines. In ACAD we could produce "squared" corners in stead of this spraypaint look.
Is there a way to get what we want in Revit or do we just need to accept yet another limitation of this program?
I am teachnig a class on Revit and I see a new check box in the setup dialog box for printing.I did go to help file and this is what it says: "Region edges mask coincident lines. Select this option if you want the edges of masking regions and filled regions to cover lines with which they coincide. (This option is available only if the Vector Processing option is enabled.)"
View 2 Replies View RelatedI thought this was going to be a piece of cake in the new Illustrator CC but I am having a few unanticipated issues:)I need to create some vector tire images with different edges, such as the top one in the image below.So I thought this would be SO easy by simply creating a pattern brush in Illustrator and then using that for the outside. So I created the shape you see in the middle image below and created a pattern brush with this shape.I then created an ellipse and used the new brush for the outline.
All of those are open paths...it has taken the shape and applied it to the outline but has kept each shape separate, so I am not able to fill the circle in black. I could of course go in and manually join each little corner separately where the little shapes meet but this will take FOREVER with all the images I have to do.
I tried the following in Illustrator,
So basically, I created coloured text inside Adobe Illustrator and however much I zoom into the text, the text always appears to have smooth edges. Once I click on 'Save For Web', the edge all around the text becomes rough and aliased. I chose GIF and PNG, but it still happens. The text is on a transparency background. The same problem applies to images when I am creating a logo.
I'm trying to snap a head with it's neck with the merge edge tool, but somewhere along the way, the edges lost there border edge characteristics and now I can't merge the edges. Is there a way to make the edges back to the way they were?
View 1 Replies View RelatedI have just installed my Photoshop_CS6 but could not detect my sscanner, Why?
View 5 Replies View RelatedAdmitting first that AI is my least fav of the Suite.. I should have found this by now. I used to use Direct Select and get a handy info on the toolbar showing me DPI/PPI in placed graphics. I just got an image from a client and am looking for this feature.... Where can I find and add it to my toolbar?
View 5 Replies View RelatedHow can I get both the 32 and 64 bit versions of CS6 to detect my graphic processor (AMD Radeon HD7700) for GPU usage in Win 7 ? Cuiurently, it is only seen in 64 bit.
View 19 Replies View Relatedyesterday i was watching the news , and they talk about images photoshopped and they named a software able to detect if an image is photoshopped..i don't remember exactly the name of the software but is something like full match (i'm almost sure about match"
View 16 Replies View RelatedI have a few questions i just downloaded the demo version
1) how do i set it up to auto detect chapters in corel video studio x5
2) i am trying to burn dvd from a sony ccd - trv43 camcorder what are the best setting to use to burn the dvd .
I tried to test the recording feature.......i made a few tests but finally i saw that when i wanted to have voice in my recording.....wasn' possible and a message appears (no audio system detect.........) I am wondering why appeared this message and how i can recording audio also in my video?
View 4 Replies View RelatedMy camera is connected to the PC via EZCAP.
VideoStudio shows EZCAP in it's video capture list and do capture video via EZCAP.
But in stop motion, VideoStudio dont list EZCAP... so no stop motion. What a disappointment...
Do you think that if VS can capture video from EZCAP, there is a way it can also detect it for stop motion?
Some tech info...
PC - win7 64 bit
CARD - EZCAP (this is an A/V to USB device)
SW - VideoStudio Pro x4
I created 2 dll's
One for autocad the other one for civil..I created another dll that loads using
Reflection.Assembly.LoadFrom("file")
the dlls into autocad at startup..I want to be able to detect if the productID is civil to be able to load the civil3d dll.
I recently switched from CS1 to CS3 and I haven't been able to get CS3 to detect the sensitivity of my tablet, although it worked fine with CS1.
View 1 Replies View RelatedI am looking for a program that detects cheating with auto-cad? Ex. Copying one persons drawing and calling it their own. I know Universities and other technical schools have such a program.
View 9 Replies View RelatedI am using Photoshop CC with Windows 7 64-bit and all plugins have issues detecting my internet connection. When trying to use them, an error message pops up saying "No internet connection detected." I am connected to the internet, am able to connect to Adobe servers, and am not using a firewall or connecting through a proxy server. I have checked my plugin settings in preferences to make sure plugins are allowed to use connections, and have tried editing the registry values in Windows to make sure that all Adobe products automatically connect to the internet, but still have had no luck. Plugins I am trying to use are Kuler and Subtle Patterns (a third party plugin).
View 1 Replies View RelatedI have a Sony vaio notebook with an intern Intel hd graphics 4000 and an additional geforce gt 640m LE graphic card with 2 GB. PS CC can't detect my nvidia card. In PS at the settings -> performance menu there is no nvida card to select, I just can select the intern graphic card at the moment if it's activated.
nvidia driver are up2date. Also have this settings done, but has no effect:
I am using Inventor 2008. When deleting a part from the project, even if that part is not in the assembly, I still cannot open the assembly because it is pointing a link is missing. I cannot detect what is the relationship between the part and the assembly. In design assistant, the part is referenced by another part but I cannot see what is the relationship in order to remove it.
View 5 Replies View Related