AutoCad :: Create Dynamic Block Using Stretch And Rotate Parameter

Apr 26, 2013

I have a block of a circle and a line coming from the left and right side quadrant of the circle to a common point (see pic). I want to create a dynamic block using a Stretch and Rotate parameter. You select the block, the Rotate point (grip) shows at the end of the two lines. I can grab that grip and rotate both lines and circle by moving this point around the screen, but cannot Stretch this point to a new location at the same time. How can I have the Rotation end point follow the Stretch parameter?

View 2 Replies


AutoCad :: Dynamic Block - Rotate / Stretch Along A Linear Path

Nov 19, 2013

I am trying to have a dynamic block that will show the profile of a steel plate, detailing the angle of a bevel. Including the plate thickness, the land, gap and the actual angle of the bevel. I've gotten most of it figured out, but having a grip to SET the angle at a specific number, while maintaining the drawing's integrity is proving difficult. I have attached the block I have created so far (minus the previous attempts to rotate the beveled angle).


The base point of the rotate parameter should be at the junction of the bevel & land. I need it to stay connected to the end point of the top-most flat line as it rotates, which means the lines need to stretch to match the changing angle. It will either rotate that line along with it, or if I apply a stretch tool, it gets all disconnected and just plain wrong.

One of the things I am liking about my current set up is I can grab a grip, and then type the number I need and it will pop on into place. Was hoping for the same effect if I typed in the angle, it would be exactly that, while also adjusting the drawing.

View 9 Replies View Related

AutoCad 2D :: Rotate Parameter And Action To A Dynamic Block

Sep 17, 2013

I am attaching a rotate parameter and action to a dynamic block.

I get the "Specify base point" bit okay but I can't figure out what "Specify radius of parameter" does.

Do I have to include or exclude other parameters like Flip or Stretch? I get some weird results when I rotate an object with other parameters.

Is it possible to place the Grip in a specific place? It always seems to like to sit on top of another parameter name.

View 9 Replies View Related

AutoCad :: Rotate Attribute In Dynamic Block With Alignment Parameter?

Jan 23, 2014

Is it possible to make a dynamical block where the attribute is horizontal in combination of the alignment parameter (not rotate)? If I align to an arc the attribute need to stay at an horizontal position.

View 4 Replies View Related

AutoCAD 2010 :: Dynamic Block Rotate Part And Stretch Arcs To Stay Connected

Jun 18, 2012

I have a block that I would like make dynamic.  It is a fishhook arrow for a roundabout traffic sign.  I would like to rotate the head to various angles, and have the body of the arrow adjust.  I already have the ability to stretch the two end points in their direction, and rotate the head, but the curved part of the arrow body needs to adjust for the new head location.  I tried dynamic stretch, but it would not attach to the rotate dimension.  How do I get these arcs to stretch along their radii and associate the end arc points to the near end of arrow head?

I had one thought of using multipe arcs so that they would overlap more or less as rotated, but this is a pretty crude workaround.

LT, C3D 2005 - 2014
XP, Vista, 7

View 7 Replies View Related

AutoCAD .NET :: Create A User Parameter For A Dynamic Block

Feb 13, 2012

We have some dnyamic block share set of parameters, if we change a parameter's value, all block that reference this parameter should be change.we can do it by program.

but create user parameters for a dynamic block must be by hand, can we create a user parameter by code? another way is user global parameter. does AutoCAD Parametric function's user value can be share with dynamic block?

View 8 Replies View Related

AutoCAD .NET :: Create New (user) Parameter For Dynamic Block?

Sep 25, 2012

I would like to add a new (user) parameter to a dynamic block within my code. I have noticed that this is possible manually. But couldn't find how to do this in .Net. When this parameter has been created it would be necessary to fill in a value. So the parameter can either be a general parameter, that can be adjusted later or a (user/dynamic) parameter specific for the block.

View 1 Replies View Related

AutoCAD Dynamic Blocks :: Linear Parameter Stretch With Polar

May 6, 2013

I am trying to be able to have my outreach arm stretch horizontally and on angles of 5 / 10 / 15 degrees from the pole. I have been able to make the polar stretch for this and it works fine though what i am trying to do is have the luminaire height also stretch and move when the size of the outreach changes (i can make the linear dimension work the way i want though not the luminaire parameter) as when you add the paremter into the stretch action is only moves the top and leaves the bottom at the same location which is not giving me the correct height. 

The block itself is alot more complicated then this I have stripped most of the parameters out to make it less confusing but the end result would allow the user to input the outreach angle, outreach length and luminaire height. I have attached drawing for your reference.

View 5 Replies View Related

AutoCAD Dynamic Blocks :: Attribute Not Rotating And Stretch Parameter

Jul 21, 2011

I am very new to dynamic blocks. I am starting off learning the small stuff before I get to the larger more complex blocks to convert to dynamic.

I have a reference block I am trying to "master" all the functions we would like to see.

I have two major concerns.

1) Why can't I rotate this block (via rotate action) and have the attributes stay at angle zero? I thought I built the parameters and actions correct.

2) I haven't ran across anything that explains how to stretch 2 linear parameters at the same time with the same distance (ex: stretch both at .25, .5, .75)

View 4 Replies View Related

AutoCAD Dynamic Blocks :: Stretch Dynamic Block Grip Points

Feb 4, 2011

I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.

I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.

But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.

View 9 Replies View Related

AutoCAD Dynamic Blocks :: Stretch A Hatch In Dynamic Block?

Jul 4, 2013

How do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.

View 2 Replies View Related

AutoCAD 2013 :: New Block A Stretch Point Appears Even If Its Not A Dynamic Block

Dec 3, 2012

my problem is whenever i make a new block a stretch point appears even if its not a dynamic block . also its not a stretch point, because when i click on it, it just move the block , and it always appear on the coordinates 0,0 it cause me a problem when I insert the block , autocad use this point as a base point , and its very far from the real block .

View 1 Replies View Related

AutoCAD .NET :: Insert Dynamic Block And Position And Stretch The Block?

Apr 6, 2013

I am trying to insert a dynamic block and position and stretch the block, using the linear parameters, depending on values entered into a form.

I managed to create a form that would draw a series of boxes. And i managed to create a routine that would insert a block and size it depending on fixed values but i can't link the 2 together.

Win 7 Pro 64bit, Dell Precision M6500

View 8 Replies View Related

AutoCAD Dynamic Blocks :: Rotate Array Parameter Individually?

Aug 25, 2011

I am trying to create a block that has a stretch and array command, but I would also like to rotate each arrayed item indvidually. However I cannot select the rotate parameter as part of the array function, so the block end up only containing one rotate grip.

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Rotate Line With Parameter Constraints?

May 29, 2012

I've only got LT2008 at the moment, but this is a pet project that if my office upgrades me I want to finish.

Is it possible to rotate a line by using the length of a separate line? But the degrees of rotation need to be worked out by the length of the line

as in the following sum

angle of rotated line = (fixed number/360) * length of linear line
Left handed and PROUD

View 9 Replies View Related

AutoCad :: Dynamic Block That Will Stretch Up And Down

Jul 26, 2011

I'm looking to make a dynamic block that will either strech up or down but some of the element stay the same in the other visivility

Here is a block i am talking about!

dynamic block.dwg

View 3 Replies View Related

AutoCAD Dynamic Blocks :: Actions And Parameter Grips Obscure Drawing-block In Block Editor

Mar 28, 2011

My drawing- block is a little bit complicated, it contains few actions and parameters and everytime i open block editor to add, or to modify some action I can't see my drawing because actions grips and parameters grips obscure my drawing. I tried to refresh layout but it doesn't work.

please take a look on attached jpg.

View 1 Replies View Related

AutoCAD .NET :: Stretch Block Dynamic Grips

May 24, 2013

I have a problem with dynamic blocks.

I have inserted a dynamic block (with .NET) and changed the value of a dynamic parameter (Linear). The block is stretched as it should be. (no problems here).

After a fiew other routines, I select the block again (by using its objectID) and a want to get the coördinates of the grip of the linear dynamic paramter. Is there a way to get the coördinates based on the linear dynamic parameter and its grip points? code in vb.Net?

View 4 Replies View Related

AutoCad 2D :: How To Stretch Ellipse In Dynamic Block

Nov 29, 2013

I know that stretch will not affect major or minor radius of an ellipse in dynamic block.

What I would like to be able to do is use properties of an ellipse and some kind of parameter to be able to affect values in properties.

I know how to get ellipse radii data out of a block, but I simply cannot find a way to get them back in...

Is there a way to link field data back to block...?

View 2 Replies View Related

AutoCad :: Dynamic Block Stretch And Array?

Feb 3, 2012

In the attached dwg, I have a dynamic block "Platform" which is used several times. I have an adjustable length, with the array set to repeat the toggles (end view of 2x4) every 2', not including the last 6". That works perfectly, except one thing. "Distance1" is the distance of the parameter, because this was the only way that I found to stop the array from showing up within 6" of the last toggle. When I insert "Platform," and click the arrow to stretch it, I can type in the distance desired minus 6", and I'll get the correct length of platform. However, I'd like to be able to type in the actual length, and have the array work appropriately (the same way it does now).

Then, I'd like to create a custom toolbar that has a button to click which will insert this platform and ask me what the length of the platform should be (the entire distance). After specifying an insertion point, the block will insert at the correct length, with the appropriate toggles.

Here's what I'd like to do with it: using datalink, I'd like to count the following: how many copies of each length of platform is in the drawing, with toggle count and length of platform specified. I have already figured out the datalink to get the value of "Distance1", it's only the issue with the toggle count that I'm trying to figure out.

View 0 Replies View Related

AutoCAD .NET :: Explode Dynamic Block With Stretch Action

Dec 4, 2013

In my Project I build a static Block by inserting dynamic blocks from a template dwg and then explode them.

Actually I create a new Data Base, insert the blocks from my template, set the according Dynamic Properties, Explode the Block in the temp DB and then wblockclone the resulting Objects in my destination BlockTableRecord.

This works fine, but:

in my source dyn. block there is an associative surface defined by a Polyline(Rectangle) , attached a stretch action to change the size. I can set the Width parameter, after the Explode the polyline itself is updated, but the planar surface is not... so if I explode this block I get a well stretched Polyline and the "base" surface.

Manipulating the dynamic Block works fine... If I have stretched 3D-Meshes, they are ok as well. It seems to be something with the planar surface object.
Dim objs As New DBObjectCollection idsToImport.Clear() If Helpers.Registry.GetValueFromRegistry("ExplodeSubs").ToString = "1" Then ' debug switch bref.Explode(objs) 'the dyn BlockRef in the external (temp) Database bref.Erase(True) For Each [code].......

View 2 Replies View Related

AutoCAD Dynamic Blocks :: Stretch A Block In Two Directions

Dec 12, 2013

I have drawn a simple block that I want to stretch in two directions manually or from the properties palatte.

My block works fine once and then breaks down.  Stretch the block in the 'Y' direction. Deselect the block. Stretch the block again and only the grip moves. Edit the block and close the block, the block resets.

View 6 Replies View Related

AutoCad :: Dynamic Block Stretch Opposite Directions

May 27, 2011

I have a dynamic block for HSS column. Previously it was always 1"x1" and I would just scale it to the proper column size I needed. Ignoring the wall thickness.

But if there was an asymmetrical HSS (i.e. 4x6) the wall thicknesses and radii of corners would look funny.

So now I want one that has Stretch Actions to change the size of the column. I added a Stretch to one side, then the other with distance multiplier of -1. But as you can see on the attached, the Linear Parameter baseline doesn't stretch. I want to have the Parameter Distance the actual full width of the column so I can change the columns with the Properties Palette. Otherwise, I would just start the Parameter from the center of the column.

View 2 Replies View Related

AutoCad :: Dynamic Block Polar Stretch And Array

Dec 6, 2007

i'm trying to do a polar stretch and array for rigid insulation. RIGID2.dwg is my best option. but as you can see in the jpg, the first line should have arrayed already, because the gap is over 2". i tried to follow the instruction someone used for the clothes hangers URL.... and it resulted in RIGID.dwg, with the lines rotating off the main line.

View 9 Replies View Related

AutoCad :: Dynamic Block - Stretch Simultaneously Different Directions?

Jun 3, 2013

The classic example of this, is a plan view of a door which shows you the opening, the arc and the door. How can I put a stretch on the opening and the door with a link in between, so when you stretch one, the other stretches with the same value?

View 4 Replies View Related

AutoCad 2D :: Stretch Mass Element In Dynamic Block?

Mar 2, 2011

I am working in ACAD 2009, I want to create a dynamic block for signage acad 2009 stretch mass element in dynamic where I need to be able to stretch hatched object. Neither mass element nor hatch do not stretch with the dynamic block. I need to see the area in 2D (not just a line).

View 2 Replies View Related

AutoCAD 2010 :: Automatic Stretch In Dynamic Block For Attribute Value?

Jun 7, 2012

We have specialized electrical schematic drawings on what is termed roll-drawings.  These roll-drawings are simply 12" tall and variable width type drawings.  We've had some as short as 24 inches and as long as 900 inches.  As a result we use these section dimensions to distinguish circuit boundaries.  It's not a real dimension, just a way to distinguish what circuit is located where.  I've tried to recreate it using a block for improved automation as currently we just use a lisp routine that draws an arrow and lines.  It looks like the screen capture of my block below.   Is it possible to have the inside endpoints of the lines automatically stretch outwardly toward the arrows as the attribute Value changs?

View 3 Replies View Related

AutoCAD 2010 :: Stretch Dynamic Block Grip Points

Jan 24, 2013

I have created a dynamic block with stretch points. I used the tester in the block editor and all works fine, but when I insert the block into a drawing, the grips for the stretch action are in a completely different place...I don't mean a different place on the block, but a different place in the drawing...way out there. so if I go into the block editor for the block while I'm in the drawing...the parameters have now moved way out of the way also, in the block...but if I actually open up the block itself and then go into the block editor, all the parameters are where i placed them in the first place.

View 1 Replies View Related

AutoCAD Dynamic Blocks :: Stretch / Move / Array Block

Jul 31, 2012

I need this block to do the following:

1. Move the right piece so it ends at 3', 4', & 5'.
2. the move right hook and 'backing' to stretch/copy (or array) so it adds a hook to the right and fills in the backing.

so this means that a 3' gets 4 hooks, 4' gets 5 hooks and 5' gets 6 hooks.

3. the block as shown is the smallest configuration with 3 hooks.

I could just set up a visibility and draw each one at it's appropriate length but I'm trying to keep this simple block to a min size. If all else fails, that's the route I'll take.

I've tried a couple different configurations and I keep getting duplicates or the end piece doesn't move the correct distance.

View 3 Replies View Related

AutoCAD Dynamic Blocks :: Polar Stretch With A Arrow Like Block

Jul 13, 2013

I am trying to put a polar stretch on the block uploaded, but it doesn't seems to work (maybe because of my constraint? ). If something major is wrong  with it, is there another way I can make the same drawing proportional when i rotate it and stretch it ? Also, after that I have to use it for vlisp. 

View 5 Replies View Related

AutoCAD Dynamic Blocks :: Stretch Rectangular Block By Both Ends

Jun 27, 2013

I've got a rectangular block that I need to stretch by both ends at the same time, maintaining the center/insertion point as it grows. I have attached the block to show what I'm working with.

I thought Linear Stretch Pair was the answer but I can't make it work.

View 5 Replies View Related

Copyrights 2005-15, All rights reserved