AutoCad :: Create Surface Not Using All Contours In A Drawing
Nov 17, 2011
I'm using AutoCAD Civil 3D 2012 and have a question about creating a surface. Firstly, I know how to create a surface and then add contours, how to add a boundary to the surface, and how to draw a polygon around contours and trim everything out and then create a surface of what's remaining but how can I create a surface from contours within a polygon I draw without trimming any contours out? That way I can have a smaller surface to work with but still have additional contours all around it.
View 3 Replies
ADVERTISEMENT
Oct 1, 2013
I created a new surface, pasted my OG surface into it, set the build to exclude elevations less than and greater than but my surface still is showing every contour range. I want to only show contours at elevations of 371.5 and 370.5
Is it because it's a pasted surface?
View 6 Replies
View Related
Feb 14, 2013
So I received a whole bunch of contours from an architect. They are lines and arc. big sweeping arcs. Whats the best and fastest way to create a good surface. I can change them globally to a polyline but I need to add vertices like every 5 or 10 feet to get a good surface. Can I select multiple feature lines (after converted) to add vertices?
View 3 Replies
View Related
Nov 15, 2012
Some background: We have a composite surface of existing surveyed contours as a TIN pasted into existing aerial contours that we received from a client. We used polylines to generate our proposed contours, and then generated a proposed surface from that. We've made a blank surface, pasted in the existing surface, and are trying to paste in our proposed surface... only the existing contours outside of the proposed suface no longer line up correctly once we do.
We've tried applying the method laid out here: [URL] ........ (and the link referenced in the bottom) but are still having trouble getting the surface to work. We've tried offsetting as little as 0.25' and as much as 5' with the feature line draped over the existing surface, but it seemed that the greater the offset, the greater the discrepancy.
Just to make sure we even tried that correctly - should the breaklines that we add be standard or non-destructive? (I've tried it both ways with little success either way, so I don't know if it matters much in this instance, but perhaps for future reference it would work.)
I've attached a screen shot of our surfaces. The pink and green lines are the proposed contours, the white dashed are the existing. The outer red line is offset 0.25'. As I've mentioned, we've tried offsetting various amounts with decreasing success.
View 9 Replies
View Related
Nov 20, 2013
I have added contours to my surface (the blue lines). For some reason the surface generated contour (the orange line) is jumping across the contours I've added.
View 8 Replies
View Related
Apr 25, 2012
My TIN surface either did not generate contours or did not display them on my drawing. I created and tried surface styles of many contour intervals(from 0.5' and 4' to 2' and 10') without success. I made sure my contour layers on both the Style Dialog box Display Tab and Layer Properties Manager were turned on, still no success.
View 6 Replies
View Related
Dec 10, 2013
This is the first time I have imported a .dgn file into Civil. The drawing contains contours lines with Z elevation data. When I create a surface using this geometry (polylines + some lines) the surface seems to be scaled in the Z axis by 12.
For example pline (from dgn) is at elevation 46' but the Civil3D surface is 552'
I assume this is a setting in the Surfaces dialog box, but I cannot find it.
Also the elevation field in Properties from the dgn contours is weird. For example, in one area the (pline) contours display -28', 26', -24', -22', -20', -18' in Properties but Civil3D interprets this as a downward slope - which is the actual field conditions. I don't understand the conversion going on here.
The geometry of the pline and contours generated from the surface seem to line up in a side or isometric view (see attachment).
View 9 Replies
View Related
Nov 6, 2013
Often I've found myself dealing with some pretty complicated surfaces that have a lot of nooks and crannies, and many of the contour lines are only in a corner of the surface or are small and closed, and thus when I find myself wanting to have contour labels on all of the contours, there's not really one line I can draw using the "Create Multiple Labels at Interval" option to ensure that every contour is labeled. Thus I end up doing "Create Multiple At Interval" with a few different lines intersecting contours, but I often end up hitting some of the contours multiple times and I get a mess of labels.
I haven't been able to find a way to automatically just multiple labels on all of the contours at an interval in one fell swoop, so I started trying to program one...but then I got stuck with that, too.
Does any built-in method of doing what I want to do, or do I need to continue pursuing a programmatic solution?
View 5 Replies
View Related
Jul 24, 2007
I have a surface with 1' and 5' contours. In model space the surface behaves normally - I can select it, add labels, change the properties, etc.
But...I have several paperspace layouts and in some of them the surface is not 'selectable', it is visible but I cannot select the object (as though it didn't exist). It does not show up in the print preview or the actual plot either. (Oddly enough, the contour labels are selectable and do print out just fine...)
The paperspace layouts are pretty much identical (plan and profile sheets of a road). There are no layout overides of any sort as far as linetype, visibility, etc.
View 9 Replies
View Related
Jul 15, 2013
Ok we have 6 identical PC's all with the same drivers, same support paths, same plotter paths. Only one PC will not print surface contours. I can open the same file(s) on any other PC and the things print w/o issue. This one PC will not print the srf contours on only a few files. Most files there is no issue...
Quite odd that it's only one machine messing up with a few files that another machine has no issue with.
Win 7 64, Xeon ES165@3.2Ghz,
64 GB RAM, Quadro K4000 (x2)
View 5 Replies
View Related
May 14, 2013
I built a corridor, then corridor surface. Then I changed the corridor onto a different profile. I noticed that the contours at the end were going crazy: the new profile ended before the corridor and everything was going down to zero elevation. So I went to edit my corridor region. I enter the required station, and my contours disappear.
Observations so far:
If I set the end of the corridor region to 2+377.91 to 2+384.54 inclusive, the contours on the surface disappear. The triangles and boundary still display, and the surface gives a Z reading when I hover the mouse over it. If I set the region end to something above 2+384.54 or something below 2+377.91 the contours reappear.
My profile ends at 2+383.00, and I would like the corridor and the surface to end there too!
C3D 2013 SP1
View 7 Replies
View Related
Oct 25, 2013
I am creating a surface from polylines and the surface is not being created per the what the polylines represent. These are simple 5:1, 3:1, and 3.5:1 slopes. The surface wants to create curves instead of straigtlines (see attached).
View 4 Replies
View Related
May 22, 2012
I've created a surface using Civil 3D 2013. I made a boundary around the perimeter of the site and I've also made some boundaries inside the site where there are no survey points. I assigned "Hide" to these boundaries when I made them in order to not have contours projecting into these areas.
However, with the exception of one of the inner boundaries, some contours are showing up inside the boundaries as well as partial contours. Why are the contours visible and how do I stop them from showing up?
View 1 Replies
View Related
Sep 27, 2013
I have an existing surface and I need to creat a surface using contour lines of a at the high point on a spillway to the bottom of my pond to calculate volumes. How do I do this?
AutoCAD/Survey Tech
Merritt LS L.L.C..
743 Horizon Ct. Suite 100B
Grand Junction, CO 81506
View 1 Replies
View Related
Nov 8, 2013
The engineers at my company digitize proposed contours in a drawing and then they want me to create a surface out of the contours....the contours usually are 2 foot contours with areas that the software tends to translate based on the contours that I selected to create the surface.....I then usually need to create a profile, which does not look accurate compared to the contours, such as low spots etc...............
My question is since the engineers at my work do not how to use the software, and I am not an engineer, making the profile look a certain way sometimes needs to be tweeked by me.... How to alter the proposed surface?I am pretty sure that feature lines cannot cross contours that I have selected to create the surface?
View 3 Replies
View Related
May 4, 2011
I want to extract contours with elevation labels from a C3D 2011 surface for use in another 2011 drawing without the surface, as polylines and labels. Is there a way to do this?
View 9 Replies
View Related
Apr 9, 2013
I have a surface that shows perfectly when restoring the PCSM layer state (Old LMAN function). When I restore the Grading layer state - the surface contours show incorrectly.
It is like a hide or mask feature turns on and off.
View 1 Replies
View Related
Jun 21, 2013
Any way to evenly space contours around a curve in a surface.
Many times I have a steep area in a surface that needs to be displayed using 1 foot contour intervals, and in certain areas the contours are crossing each other around curved areas, like a curve in a ditch. In the past i have had to "fudge" the surface a little to get the contours to look correct.
View 7 Replies
View Related
Apr 12, 2012
attached is Roadway.dwg file
I made "Road" surface from Corridor Properties / Surfaces... but when I go to surface properties for "Road"...the statistics tab is blank.
2013 Civil 3D
View 2 Replies
View Related
Nov 5, 2013
I need to output the contours my surface model to a genio for use in Mx. I have the Genio exporter tool installed but when i output the genio all that appears is the Boundary line without the contours, which when i think about it makes sense as the surface contours is more a display option rather than actual contours. Is there a way of exporting the contours via genio.
View 4 Replies
View Related
May 3, 2013
I have tried multiple types of hide boundaries,etc. for this, and cant find a solution. I'm sure it is very simple, but..
I need a corridor that transitions from 2% sideslope to 0% sideslope. This transition occurs in a horizontal AND vertical curve. I understand I could use EOP alignments, profiles, etc to achieve this. I dont have the time or civil3D knowledge to figure this out on a friday afternoon...
So... my plan is to not apply the transition, and just hide the contours in the transition area and sketch them in by hand. I want to corridor surface to remain so that when other profiles are created from this surface it is still somewhat accurate (instead of removing this portion of corridor surface, and adding simple contours to the surface). I just want the surface hidden for +/- 50'.
Everything I have tried hides the surface everywhere, including new profiles from the surface.
View 8 Replies
View Related
May 2, 2012
I have a existing ground surface drefed into a model and am trying to get a user defined contour at a set elevation but nothing appears. I have userdefined layer on in the surface style and other ideas why it will not appear?
[URL] ......
View 9 Replies
View Related
Mar 15, 2013
I'm running 2012. Is it still true that I need to label my contours in every drawing? I have a drawing that contains my existing surface (about 90 Acres). I have labeled the contours in that drawing. I then have a output drawing that the existing contours are a data shortcut. The contour labels do not show up.
View 3 Replies
View Related
Jun 6, 2012
I just installed AutoCAD 2010 Civil 3D on a 32 bit Windows 7 machine. When I open a dwg sent from a surveyor I can see and manipulate all the linework, contours, points, and SRF breaklines in the drawing. When I proceed to save the file to my computer and reopen it, the contours and points disappear; however all linework and surface breaklines remain. The two files that I have been working with were saved originally in 2004 and 2007 format. I have tried saving to their respective versions but that has not worked.
The only way that I have been able to retain these objects is by first exploding them and making them into a block and later inserting them into the other drawing. If I try to make them into a block without exploding them they also disappear.
Is there a way to retain all drawing objects directly from saving?
View 2 Replies
View Related
Dec 4, 2012
I've an old countour map (hard copy drawn ages ago) which now I want to digitize.
I've scanned this map (can be saved in JPEG, PDF etc format) however I don't know if there is an easy way to create contour lines from this JPEG image.
View 9 Replies
View Related
Jan 11, 2013
I have a drawing with contours every 1m and according to the area that I have to display in my layouts I have to display contours either 2m, 5m or 10m.
How is possible to create labels for only this elevations and if it is possible, create several labels along one of these contour with specific interval.
View 9 Replies
View Related
Dec 10, 2012
I'm trying to create structure contours from drill holes, where I do not have a significant number of drill holes for the area being modeled. I've tried all of the contouring options, using strata polylines, and smoothing contours. creating smoother, more realistic contours?
View 3 Replies
View Related
Oct 2, 2012
I am issues with DEM files that I am downloading from the USGS website.I download 24k, elevation for the area I need. I then choose staged 1 second, add a surface to a blank drawing, then upload the DEM files to the surface.
The surface imports correcty, but when I try to import points taken by a surveyor on the same drawing, they plot incorrectly.The DEM surface and the points from the surveyor do not correspond. Also, the DEM surface is in meters, not feet. I have tried changing drawing settings, datum types, coordinate types, etc.
View 9 Replies
View Related
Mar 1, 2013
Im currently using an addon for Civil 3D called Novapoint. It allows me to create 3D models of surfaces made out of 3d faces and easily models cut and fill 3d-models for me.
The only thing i need to create a cut and fill model is one or several ground surfaces (existing ground, earth layers, rock etc. whatever i need) and a closed polyline/3Dpolyline that represents the level I want my cut and/or fill model.
I enter the spcifications I want such as; earth cut angle, rock cut angle, fill angle, select which surfaces i want to include in the model calculation and select the polyline.Novapoint then calculates the cut/fill model from the surfaces to the polyline and models the different cut/fill angles and gives me the results in a 3d-face model and a specification of the volyme of rock cut, earth cut an fill.
1. Novapoint is quite unstable and crashes alot
2. You cant create profiles out of 3d faces
3. Novapoint does not automaticly combine the start surfaces with the modeled cut/fill surface
4. A large surface made out of 3d-faces demands alot of computer power
So I want to how I do the same that Novapoint does for me in Civil 3D? (I have access to Civil 3D 2007-2013 depending on which one you're using)I know I can take the 3Dfaces i created in Novapoint and make a surface in Civil 3D with them but I want to exclude Novapoint completely.
View 9 Replies
View Related
Nov 25, 2011
I'm using AutoCad 2007. I'm trying to map a simple 2D flat drawing onto a curved surface.
I have a 3D drawing of a very simple curved floor, similar to a skateboard ramp or a photographers infinity curve backdrop. I also have a 2D design. I simply want to drop my 2D drawing onto this curve, so that it follows the geometry of the curve's surface.
View 8 Replies
View Related
Apr 30, 2013
when I try to use rulesurf between 2 circles on an angled plane, the surface twists instead of drawing a cylinder.
View 2 Replies
View Related
