AutoCAD Civil 3D :: Hide Portions Of Corridor Surface From Displaying Contours
May 3, 2013
I have tried multiple types of hide boundaries,etc. for this, and cant find a solution. I'm sure it is very simple, but..
I need a corridor that transitions from 2% sideslope to 0% sideslope. This transition occurs in a horizontal AND vertical curve. I understand I could use EOP alignments, profiles, etc to achieve this. I dont have the time or civil3D knowledge to figure this out on a friday afternoon...
So... my plan is to not apply the transition, and just hide the contours in the transition area and sketch them in by hand. I want to corridor surface to remain so that when other profiles are created from this surface it is still somewhat accurate (instead of removing this portion of corridor surface, and adding simple contours to the surface). I just want the surface hidden for +/- 50'.
Everything I have tried hides the surface everywhere, including new profiles from the surface.
View 8 Replies
ADVERTISEMENT
May 14, 2013
I built a corridor, then corridor surface. Then I changed the corridor onto a different profile. I noticed that the contours at the end were going crazy: the new profile ended before the corridor and everything was going down to zero elevation. So I went to edit my corridor region. I enter the required station, and my contours disappear.
Observations so far:
If I set the end of the corridor region to 2+377.91 to 2+384.54 inclusive, the contours on the surface disappear. The triangles and boundary still display, and the surface gives a Z reading when I hover the mouse over it. If I set the region end to something above 2+384.54 or something below 2+377.91 the contours reappear.
My profile ends at 2+383.00, and I would like the corridor and the surface to end there too!
C3D 2013 SP1
View 7 Replies
View Related
Jul 13, 2012
I'm having a random issue with the daylight ties lopes not tieing to the EG surface at all stations in the Corridor Section Editor. Some stations daylight fine. In plan view the daylight lines vary left & right as expected but don't display at all in Section Editor.
Some background info:2012 Civil 3D SP1 / 64 bit / WIN7Simple corridor used1 alignmentSame fg profileSame drefd EG surface (set all targets for daylight LT/RT)Only one assembly applied to entire corridor Attached are 2 captions of the issue I'm having which each have a cut & fill occurrence as well as a caption of the entire align. & corridor. I did try deleting corridor & recreating and even recreated a simpler assembly and still have the daylight issue in same areas of corridor.
View 2 Replies
View Related
Nov 15, 2012
Some background: We have a composite surface of existing surveyed contours as a TIN pasted into existing aerial contours that we received from a client. We used polylines to generate our proposed contours, and then generated a proposed surface from that. We've made a blank surface, pasted in the existing surface, and are trying to paste in our proposed surface... only the existing contours outside of the proposed suface no longer line up correctly once we do.
We've tried applying the method laid out here: [URL] ........ (and the link referenced in the bottom) but are still having trouble getting the surface to work. We've tried offsetting as little as 0.25' and as much as 5' with the feature line draped over the existing surface, but it seemed that the greater the offset, the greater the discrepancy.
Just to make sure we even tried that correctly - should the breaklines that we add be standard or non-destructive? (I've tried it both ways with little success either way, so I don't know if it matters much in this instance, but perhaps for future reference it would work.)
I've attached a screen shot of our surfaces. The pink and green lines are the proposed contours, the white dashed are the existing. The outer red line is offset 0.25'. As I've mentioned, we've tried offsetting various amounts with decreasing success.
View 9 Replies
View Related
Sep 14, 2012
I have created a surface from a corridor. I set the boundary of the surface to the daylight of the corridor. In some areas of the corridor the surface does not triangulate see attached.
View 2 Replies
View Related
Mar 6, 2012
I have defined 3 user-defined contours for various elevations in my pond. I would like to disply them differently from one another, so I set their display styles in the analysis window where I created them. Unfortunately, the are only displayed per the settings in the surface style which is 1 - not what I want and 2 - all identitical. I have tried various settings in the surface style, but the contours will not display the way I have selected in the analysis window.
C3D 2011 w/ latest updates
View 6 Replies
View Related
Mar 21, 2013
My corridor surface is not matching my corridor top links. see attachments. this is affecting my volumes!
The section-plan(surface red).png is showing the section editor and the plan view. the red highlighted line in section is the corridor surface and as you can see in plan view the surface is incorrect and wiggly.
The pdf is all my sections with the red linework being the corridor surface.
C3D ver 2012
Win 7, 64bit
View 2 Replies
View Related
Feb 13, 2013
I am curious if it is possible to modify only specific portions of a surface? For example, I have recieved an xml surface representing FG for a project, and want to do an earthwork calculation, could I raise and lower only portions of the project say by using specific boundaries for the asphalt paving, concrete etc. and then implement the raise & lower surface feature for these portions of the FG surface.
At this time I have been creating multiple surfaces for each particular feature of the site, then paste the FG surface, add a boudary and lower appropriately. Finally, I have to go through and paste each particular feature and its small surface into one "subgrade surface" to get an accurate representation. This method results in countless small surfaces and alot of leg work for something that seems like it should be simple.
I know that the surface defentions (FL's or corridors), should they be provided, would make this easy, but there have been several occasions where these are not being made availble by the project sponsor.
View 9 Replies
View Related
Dec 29, 2010
It seems to happen randomly and I can't tell what triggers it. Everytime I regen or autosave/save the status shows "displaying contours" and a load bar that takes way too long and slows me down...
View 9 Replies
View Related
Mar 26, 2012
all of a sudden whenever I run audit on my corridor file the surface definition becomes a snapshot. To add to the drama, the corridor surface will not paste into an empty surface. Why?
View 2 Replies
View Related
Nov 20, 2013
I have added contours to my surface (the blue lines). For some reason the surface generated contour (the orange line) is jumping across the contours I've added.
View 8 Replies
View Related
Apr 25, 2012
My TIN surface either did not generate contours or did not display them on my drawing. I created and tried surface styles of many contour intervals(from 0.5' and 4' to 2' and 10') without success. I made sure my contour layers on both the Style Dialog box Display Tab and Layer Properties Manager were turned on, still no success.
View 6 Replies
View Related
Feb 7, 2013
My problem added with pic ... I want to make volume calculate for sample road project. When I try to compute materials I cant use Corridor surface for DATUM... There is only target surface on option..
View 2 Replies
View Related
Mar 6, 2012
I am trying to visualize a road project. The problems is, whenever the corridor surface goes below the EG surface (when the road is in cut) the EG surface is the only visible surface.
I sort of need to subtract the corridor surface from the EG surface, or merge the both surfaces into one.
View 3 Replies
View Related
Feb 28, 2013
I have a corridor with 2 intersections. It is more or less like a main road with an off-ramp and an on-ramp, both on the same side, with a big triangle shape island in between them. It involves an existing road widening and a connection with another existing road. Since it is a real scenario, the intersections aren't perfect 90 degrees nor the offsets are constant.
Create Western intersection and change offset and curb return targets to design aligments.Create Eastern intersection and change offset and curb return targets to design alignments.Model the corridor as per design requirements.Due to design constraints, I ended up removing both intersections. I didn't delete all the offset and curb return alignments although they're not targeted on any region. Deleting this alignments seems to make C3D crash. the actual intersection definition hasn't been removed, as I read on other threads. I kept on getting a couple of error messages on Panorama Event Viewer every time I rebuild the corridor.
So, the problem comes when I try to output the cross sections from this nice looking corridor. They all look fine until they reach the intersection area. From the intersection onwards, the corridor is not displayed on any cross section. Even way passed the western intersection.
Why the corridor doesn't display on the cross sections passed the deleted intersections?I have a bad feeling that removing the intersection wasn't a good idea in the first place but it's too late now.
View 4 Replies
View Related
Dec 7, 2012
Using 2012, latest SP. I have a master drawing @ 1:500 with alignment, prof's, corr, etc. I have a second drawing @ 1:200 to be used for section views. I've data referenced the alignment, prof's, srf's, etc. I've created the section views in the section view dwg and xref'd the master dwg.
My problem is that the corridor model will not display in section views anywhere along a spiral in the 1:200 dwg. It displays fine everywhere else along the alignment. Just not spirals.
I have section views in the master drawing that will display the corridor just fine in section view at these same stations along the spirals.
View 9 Replies
View Related
Aug 20, 2013
Section editor shows the Existing Ground and the Assembly correctly. But "Create Multiple Views" Shows a blank Grid from -10 to 0..... Corridor rebuilt...
View 5 Replies
View Related
Dec 10, 2013
This is the first time I have imported a .dgn file into Civil. The drawing contains contours lines with Z elevation data. When I create a surface using this geometry (polylines + some lines) the surface seems to be scaled in the Z axis by 12.
For example pline (from dgn) is at elevation 46' but the Civil3D surface is 552'
I assume this is a setting in the Surfaces dialog box, but I cannot find it.
Also the elevation field in Properties from the dgn contours is weird. For example, in one area the (pline) contours display -28', 26', -24', -22', -20', -18' in Properties but Civil3D interprets this as a downward slope - which is the actual field conditions. I don't understand the conversion going on here.
The geometry of the pline and contours generated from the surface seem to line up in a side or isometric view (see attachment).
View 9 Replies
View Related
Nov 6, 2013
Often I've found myself dealing with some pretty complicated surfaces that have a lot of nooks and crannies, and many of the contour lines are only in a corner of the surface or are small and closed, and thus when I find myself wanting to have contour labels on all of the contours, there's not really one line I can draw using the "Create Multiple Labels at Interval" option to ensure that every contour is labeled. Thus I end up doing "Create Multiple At Interval" with a few different lines intersecting contours, but I often end up hitting some of the contours multiple times and I get a mess of labels.
I haven't been able to find a way to automatically just multiple labels on all of the contours at an interval in one fell swoop, so I started trying to program one...but then I got stuck with that, too.
Does any built-in method of doing what I want to do, or do I need to continue pursuing a programmatic solution?
View 5 Replies
View Related
Jul 24, 2007
I have a surface with 1' and 5' contours. In model space the surface behaves normally - I can select it, add labels, change the properties, etc.
But...I have several paperspace layouts and in some of them the surface is not 'selectable', it is visible but I cannot select the object (as though it didn't exist). It does not show up in the print preview or the actual plot either. (Oddly enough, the contour labels are selectable and do print out just fine...)
The paperspace layouts are pretty much identical (plan and profile sheets of a road). There are no layout overides of any sort as far as linetype, visibility, etc.
View 9 Replies
View Related
Jul 15, 2013
Ok we have 6 identical PC's all with the same drivers, same support paths, same plotter paths. Only one PC will not print surface contours. I can open the same file(s) on any other PC and the things print w/o issue. This one PC will not print the srf contours on only a few files. Most files there is no issue...
Quite odd that it's only one machine messing up with a few files that another machine has no issue with.
Win 7 64, Xeon ES165@3.2Ghz,
64 GB RAM, Quadro K4000 (x2)
View 5 Replies
View Related
Oct 25, 2013
I am creating a surface from polylines and the surface is not being created per the what the polylines represent. These are simple 5:1, 3:1, and 3.5:1 slopes. The surface wants to create curves instead of straigtlines (see attached).
View 4 Replies
View Related
May 22, 2012
I've created a surface using Civil 3D 2013. I made a boundary around the perimeter of the site and I've also made some boundaries inside the site where there are no survey points. I assigned "Hide" to these boundaries when I made them in order to not have contours projecting into these areas.
However, with the exception of one of the inner boundaries, some contours are showing up inside the boundaries as well as partial contours. Why are the contours visible and how do I stop them from showing up?
View 1 Replies
View Related
Sep 27, 2013
I have an existing surface and I need to creat a surface using contour lines of a at the high point on a spillway to the bottom of my pond to calculate volumes. How do I do this?
AutoCAD/Survey Tech
Merritt LS L.L.C..
743 Horizon Ct. Suite 100B
Grand Junction, CO 81506
View 1 Replies
View Related
Nov 8, 2013
The engineers at my company digitize proposed contours in a drawing and then they want me to create a surface out of the contours....the contours usually are 2 foot contours with areas that the software tends to translate based on the contours that I selected to create the surface.....I then usually need to create a profile, which does not look accurate compared to the contours, such as low spots etc...............
My question is since the engineers at my work do not how to use the software, and I am not an engineer, making the profile look a certain way sometimes needs to be tweeked by me.... How to alter the proposed surface?I am pretty sure that feature lines cannot cross contours that I have selected to create the surface?
View 3 Replies
View Related
Jun 20, 2012
Running version 2012 of Civil 3d
We have an urban divided highway resurface and widen project. We have an eastboiund and westbound corridor we would like to get to display on our single set of cross sections
We originally set up our corridor to do the widening and ditches portion and then went on to do the work to set up the model to do the resurfacing. When we did the sections for the ditches only they displayed fine. Now that we have the resurfacing incorporated into it the ditches no longer display.
we have reviewed the targets of our assemblies, we have reconstructed the cross sections, to no avai. The software is not doing us any good right now. Need to get smarter
View 3 Replies
View Related
May 4, 2011
I want to extract contours with elevation labels from a C3D 2011 surface for use in another 2011 drawing without the surface, as polylines and labels. Is there a way to do this?
View 9 Replies
View Related
Oct 1, 2013
I created a new surface, pasted my OG surface into it, set the build to exclude elevations less than and greater than but my surface still is showing every contour range. I want to only show contours at elevations of 371.5 and 370.5
Is it because it's a pasted surface?
View 6 Replies
View Related
Apr 9, 2013
I have a surface that shows perfectly when restoring the PCSM layer state (Old LMAN function). When I restore the Grading layer state - the surface contours show incorrectly.
It is like a hide or mask feature turns on and off.
View 1 Replies
View Related
Jun 21, 2013
Any way to evenly space contours around a curve in a surface.
Many times I have a steep area in a surface that needs to be displayed using 1 foot contour intervals, and in certain areas the contours are crossing each other around curved areas, like a curve in a ditch. In the past i have had to "fudge" the surface a little to get the contours to look correct.
View 7 Replies
View Related
Apr 12, 2012
attached is Roadway.dwg file
I made "Road" surface from Corridor Properties / Surfaces... but when I go to surface properties for "Road"...the statistics tab is blank.
2013 Civil 3D
View 2 Replies
View Related
