I'm trying to extract the 3d length of multiple lines into either a CSV, SSV or directly into a table, I have done a fair amount of research but all of the solutions seem to be for later versions of CAD than the one i'm currently using, I think 2008 is the first to have embedded data extraction for objects as well as attributes?
View 6 RepliesCorelDraw_ExtendedLines.JPG
I have a time consuming problem that I was hoping a work-around or solution could be found for.
Some background: I use CorelDraw sort of as a CAD file creation software. The tool I use traces out straight, horizontal and vertical lines. At times, there are areas that need to be excluded being processed over, so my design has holes and gaps in it. The tricky part is, the tool I use needs time to accelerate up to full speed before I want it to start it's process. This requires that I add the same length to every single line in the layer (different layers need different added lengths). The problem that I run into, is that if I select multiple groups of lines that are not the same length and try to extend them, CorelDraw sees them as one group and extends the largest lines the right distance, but shorter lines get a different percentage of the distance, and gaps get shifted. I put in pictures of what I am talking about (a before, a good, and a bad).
can I select all the lines in a layer and tell CorelDraw to add X length to all of them, while keeping their center positions the same? It would save me a good deal of time.
How do I connect two lines that have set lengths and set points at the other end
View 1 Replies View RelatedI had to go out yesterday and measure an house indoors. Anyway the room is not square but sort of an triangle. I have measured 3 wall sides.
How to arrange them so that I get an triangle. I could draw 3 lines and then start rotating them till I get satisfactory result but can this be done any quicker?
I'm creating an assembly and in this assembly I need to add some foam pieces. These pieces are the exact same part number but can vary in length. How can I make such a part so that i can insert it into an assembly multiple times but have different lengths? I'd rather not make multiple pieces of foam for every single assembly for all of our product lines and am looking for the "one foam to rule them all" option. I would assume this would be an ilogic component I would have to create, but i haven't really made a part like that yet.
View 3 Replies View RelatedLabeling lines with their lengths,
I got the attached lisp file from the web which automatically labels the lines with their length. Resulting the values of the length in the absolute values of the length instead of saying that the length is in inch. i.e, i need to remove the inch sign (") from the suffix of the length.
I checked a couple of old posts looking for a lisp routine that will count the number of lines and list each different length either in a dialog box or txt file. I am working on an estimate and I have a floor plan of owsj of different lengths. I downloaded the tlen.lsp but that is only giving the total number of joists and the total length.
I am looking for a lisp so that I can window all the owsj at once and have it list or show the result for the joist in this manner
sample output:
xx joists = 10'-0"
xx joists = 20'-0"
xx joists = 30'-0"
Is there an Autocad command that will list the lengths of several seperate lines and combine the lengths similar to the areas command?
View 3 Replies View RelatedAre there any working .arx files or lisp routines that would enable me to calculate a total length of multiple blocks ? I know there is TLEN out there but this does't work for blocks, I need something that will calc combined lenghts of my user defined blocks which are basically simple lines of varying lenghts.
View 5 Replies View RelatedIf I have a series of lines on a layer, is it possible for a macro to place a label for the lengths of the lines at the center of each line in AutoCAD LT 2012? Adding a DIMLINEAR to each line is for the birds....my drawings have as many as 250-300 lines that need to be labeled with thier lengths.......
View 9 Replies View RelatedI am drawing an electrical circuit in Auto-cad 2007. I have wires with 2 sizes viz. 0.5 sq.mm & 1 sq.mm. let me know how to impart thicknesses to different lines in Auto-CAD.
View 6 Replies View Relatedhow to extract the attribute value of a particular block in multiple drawings to an excel file.
Eg... there are nearly 800 drawings where I need to list down the description and Drawing number which is mentioned in the title block name "Title". The Drawing Number and the description is done in same attribute block. extract the data into an excel file or txt file. All the drawings are saved in one location.
I need to join multiple lines to a new polyline..The lines are filtered by a selectionset
Dim oPline as new Polyline()
For Each oSel As SelectedObject In acSSet
Dim oEnt As Entity = TryCast(acTrans.GetObject(oSel.ObjectId, OpenMode.ForRead, True), Entity)
oPline.JoinEntity(oEnt)
End If
Next
The error occurs on the oPline.JoinEntity(oEnt)
I have a large group of lines that I want to get a total length of. Right now the only way that I know how to do this is to highlight them all and use the list command but then I have to go through the text box and write down each line length and then add them up. This is fine if I have only a few lines but when you get into the hundreds or thousands it becomes a monster task.
I tried copying the text box data into a Word document, removing all of the text except for the line lengths and then dumping that into Excel to calculate. This works ok for a hand full of lines but is not really practical.
I know that there are LSP routines that can do this in the full version of AutoCad but LSP is not supported in AutoCad LT.
Is there a way to automate this process in LT?
Or maybe extracting just the length data from a line to a text file where I can send it to Excel and use Excel to add up the lengths?
I need to divide thousands of lines into half, but AutoCAD divide command can only allow you to select one line at a time.Is there any way we can divide multiple lines at once.
View 3 Replies View Relatedhow i can break multiple lines where they intersect, I have done research on Qbrick but cant seem to download one that works
View 1 Replies View RelatedIf i create a box in 2d,after extrude,it is a solid;but if i create 4 lines to form a box ,after extrude,it is 4 walls?is it possible ,if i have many lines,to convert mulitiples lines to polylines and i can create a solid easier?
View 9 Replies View RelatedI am basically looking for a way to get the length of each polylie segment in the overall polyline. Not the total length.
I then need to comapre these lengths. I guess I could do some math to get the values of the verticies, but is there a built in method to do this? how to get started?
I'm having a minor issue with one of my drawings. The existing drawing was a .hln file that I have opened in AutoCAD 2011 LT.
I tried to draw a line of length 1600mm but when I take a dim it's only 145mm but via properties its 1600mm. The drawing is attached zoomed-in on issue area.
How i'm adding lengths of individual plines...I am running MEP 2013 and lately we've been doing a lot of measuring of plines...The problem i'm having is that we are supposed to add 24' to every length...So if I measure a polyline and it's 10' long, the number i'm supposed to be putting on the drawing would be 34'...Is there a way to create a command that will automatically add what I need to every pline?
View 9 Replies View RelatedI can't click on multiple lines to erase or copy, it will only let me do 1 line at a time.
View 1 Replies View RelatedHow to obtain the points in a polyline from multiple lines that cross the polyline.
View 1 Replies View RelatedIs there any way to extend multiple grid lines to a perpendicular line?
View 1 Replies View RelatedI've been trying to figure out how to add or make possible, multiple lines in the title block for the iProperties on title blocks. We have a custom title block here but the box is i a little too narrow for quite a few of the titles. it has plenty of height for two or even three lines.
View 9 Replies View RelatedJust discovered the IMPRINT command... noticing that it will only imprint a single object at once.
How to enable the command to IMPRINT multiple lines onto a single solid?
I'm literaly just starting to use CAD so this might be a silly question, but how would I offset a line more than one distance in a command? Is there like a symbol you put between each distance like 2000;2250;2650 or something along those lines (no pun intended).
View 2 Replies View RelatedHow do you break multiple lines along a line?
I.e. you have ten horizontal lines 3m long and one vertical line running down the center of the 3m lines. I need to break the horizontal lines in two where they touch the vertical line without having a line smaller then 1.5m.
On a single line I can do it using the F command and clicking twice on the intersection but is it possible to select multiple lines ant the same time and use the crossing line to cut along?
I've been trying to figure out how to do this. I have a file with 41 drawings, and 7650 objects. and i want all the lines, arcs and circles to be turned into polylines. Now the Mpedit command doesnt really do it for me.
Command: MPEdit
Select objects: Specify opposite corner: 4632 found, 10 groups
Select objects:
divide by zero
This is what happens when i write MPEdit, mark everything in my drawing and press enter. Now i also tried marking a line, using select similar, and fixing it that way. but i get the "divide by zero" error aswell.
I want to create a segmented polyline with known angles / lengths, but I want to do this in 1 operation without having to copy/rotate/chamfer etc.
I'm sure it has something to do with UCS, but I've not used it in quite some time, I am stumped and everything I have tried so far has failed.
I have a DI-3C structure that I want to stretch to specific throat lengths. I want hold the stretch from front mid point of the line with the lookup for throat lengths. I'm not getting where to do my first corner of stretch frame.
View 2 Replies View RelatedProject involves repeatedly mirroring a line by selecting mutiple lines to do the mirroring. Probably sounds confusing.
The progress so far can be found here: [URL] ........