I've been trying tons of different solutions to solve this problem: insert a block that has an attribute which happens to be the last object id.
This is the best code I tried so far but without any succss.
(defun c:q1()
(command "_.PLINE")
(while (= (getvar "CMDNAMES") "PLINE")
(command pause)
[Code] .....
Have an AutoLisp program that inserts a block with attributes. Been using it forever. Yesterday I ran the program and somehow when the block is inserted, it skips the Y scaling factor. The program should insert a block at a point with a X scale of 19.2, Y scale of 19.2, Rotation at 0 and then four attribute values.
What is happening is the block is inserted at the correct point and X scaling factor, but the Y scaling factor goes in for the Rotation angle (19.2 degrees), the Rotation angle goes in as the first attribute and the remaining attributes are shifted over and the last attribute is missing.Line of code is:
(command "INSERT" "CNVTAG" inspt scl scl 0 text1 text2 text3 text4)
The command prompt displays:
Command: (command "INSERT" "CNVTAG" inspt scl scl 0 text1 text2 text3 text4)
INSERT Enter block name or [?] <NEWWHDBORD>: CNVTAG
Units: Inches Conversion: 1.0000
Specify insertion point or [Basepoint/Scale/Rotate]: Specify scale factor <1>:
19.20000000000000
Specify rotation angle <0>: 19.20000000000000
Enter attribute values
Conveyor number: 0 Conveyor Speed: 5315-BCS Motor Horsepower: 1.5hp Release
Mode: 45/90fpm
I looked at the system variables INSUNITS, INSUNITSDEFTARGET and INSUNITSDEFSOURCE AND THEY ARE ALL SET AT 0..Currently using AutoCAD 2010.
I need a function that will allow me to do a "divide" with blocks but I need the single attribute to remain intact.
I need the blocks to align with object and keep the attribute. I did get it to work with constants but the function that I need to run next failed because of the constant. My variable is preset and locked.
I'm using a blocklibrary, where I stored all my blocks, most of them have attributes.
Now I'd like to simplify my workflow and want to update the blocks that I inserted in a drawing trough LISP.
Is there a way to update all inserted blocks and attributes of the whole drawing a once? The idea is, that the LISP checks the whole blocklibrary and updates the inserted blocks that to not match with the once from the library.
We wanted to automatically fill a block's attributes from a selection in Excel. I have a piece of code that has the user select/pick a block to fill. What I want is for the selection to fill multiple blocks in an active drawing. Some of the blocks are the same - which means the same tags/attributes. I've included the code that allows the user to select the block and throws the Excel selection to certain attributes.change the code so that
1) I don't have to manually select blocks - it will find them.
2) One cell (from Excel) will go to multiple blocks - some are same block name.
3) An IF statement that if a certain cell isn't blank/nil
(pretend it would be (nth 21 vl) change DESC11 to XYZ and DESC12 to ABC. For Block namesake we'll call one, BLOCK1 (say it has 3 instances and gets different info in each case) BLOCK2 (say it has 2 instances, also gets different info) BLOCK 3 AND 4 both have an attribute - DESCAA1 that gets different info from Excel.
(defun C:AUTOFCM (/*error* adoc attribs blkobj enExcelapp Sel Sht Rng vl Wbk ) (defun *error* (msg)(if adoc (vla-endundomark adoc)) (if (and msg(vl-positionmsg '("console break""Function cancelled" "quit / exit abort") ))(princ msg)(princ "Error!") ) gc) (princ) ) (or adoc (setq adoc (vla-get-activedocument (vlax-get-acad-object))) ) (vla-startundomark adoc) (alert "Select a range of cells in Excel.") (setq ExcelApp (vl-catch-all-apply (function(lambda ()vlax-get-or-create-object "Excel.Application") )) ) ) (if (vl-catch-all-error-p(setq Wbk(vl-catch-all-
[code]....
i am trying to restrict users from modifying certain attributes in a block,i can create the blocks with some of the attributes on locked layers, but then autocad pops up an annoying alert box, is there a way to disable this? the other option i can think of is to redefine the commands *ddedit, *attedit, *ddatte,*attipedit,
View 5 Replies View RelatedI need a lisp code to burst all "blocks with text/attributes inside" in selected area. That means user should select an area (window selection) and lisp program should be find all blocks with TEXT or ATTRIB inside in selected area and then applys "BURST express tools" command to all these blocks in the selected area by user.
View 9 Replies View RelatedThere is a quick way to remove all attributes, including in nested blocks. Looking some lisp in the forum, I can't find one code for remove this elements completely.
View 9 Replies View RelatedAny routine that will allow to draw a polyline through existing blocks, in the order the blocks should be numbered? Therefore when the sequence has been specified by the polyline then user to define the number system required, and the blocks are automatically numbered in the sequence of the polyine start to finish.
View 9 Replies View RelatedHow to create a lisp to automatically export attributes from selected blocks to defined txt file without having to everytime confirm the file name, location and if the file shall be replaced?
Meaning is that I often export attributes to txt file for further use. It is always the same file (I just overwrite it always).
The way I do it now is selecting blocks, using ATTOUT command, then going to the desktop, selecting ATT.txt file and confirming that it is to be replaced.
Is there a way to make lisp or script that will just do all it in at once?
I found on forum such a lisp as below, but it exports all ablocks on drawing and it exports to txt file which is located in same place as drawing and with same name as drawing. Tried to modify it but without success:
(defun cut-att ()
(load "attout")
(setq fna (strcat (getvar "dwgprefix")
(acet-filename-path-remove (acet-filename-ext-remove (getvar "dwgname")))
".txt"
))
(setq ss (ssget "X" '((0 . "INSERT") (66 . 1))))
(bns_attout fna ss)
)
Same question for ATTIN - I use attin and always same file name from same location - how to automate it with one command?
I am looking for a way to create a master list of construction notes then use blocks attributes with fields to link to that master list. That way if the master list changed the note bubbles would change as well.
Sheet sets are being used with this project but I can't think of a way to make it work with the existing sheet set technology.
(defun CELBLKS ( / e blk ss blkl)
(setq blkl "" ss (ssadd))
(while (setq e (entsel "
[Code]....
i have this lsp, it works great but how can modify it if i want select with a window.? exemple: if i have 3 differentes blocks, i want to select them with windows and the lisp select all blocks that are identical of those 3.?
know a lisp routine that would insert a block @ a specific point on an arc? For instance if I have an arc that has a radius of 20'-0" & I want to insert a block at a set distance from the end of the arc.i could probably use the divide or measure command but I was hoping I could do it with lisp. I would also like to be able to move the object along the path of the arc at a specific distance.
View 6 Replies View RelatedI have a lisp routine:
(defun getLayout (pos / result cLayout layouts^ i len)
; pos = -1 return previuous layout name
; pos = 0 return current layout name
; pos = 1 return next layout name
(cond
((zerop pos)
(setq result (getvar "ctab"))
); case
[code]...
which basically returns either the current, previous or next tab name depending on what you call up. Any way to link this lisp to a field? I am doing some plan and profile drawings which contain match lines I would like to have the match line text automated. For example if I'm on layout called PP02 there would be two match lines in the drawing one would read MATCH LINE PP01 and the other would read MATCH LINE PP03 this lisp routine returns the correct variable but how do I loink this to a fiels?
I want to insert a stored block into a drawing (model space). Below is the code I'm using and I get Runtime Error '5': Invalid procedure call or argument.
Sub Dummy()
Dim COESTD_obj As AcadBlockReference, InsPtStd(0 To 2) As Long, COESTD As String
COESTD = "C:JimHYDROCAD_DwgsBlocksZ_COE_STDS.dwg"
InsPtStd(0) = 0#: InsPtStd(1) = 0#: InsPtStd(2) = 0# 'Set insertion point as 0,0,0
Set COESTD_obj = ThisDrawing.ModelSpace.InsertBlock(InsPtStd, COESTD, 1#, 1#, 1#, 0#)
End Sub
Is it possible within ACADE 2011 to use a lisp command to create a ladder with a set spacing, ladder # scheme, and rung spacing?
Typing AELADDER into the command line brings up the dialogue box where you can fill out the above information, but typing (command "AELADDER") returns an error. I'm not sure if that error is because it doesn't recognize it, or if it's because I don't have any variables after "AELADDER".
Using lisp to insert a dynamic block that uses an align parameter. I have a rather elaborate lisp program that I am adding to so that it can insert one of my library blocks which contains an alignment parameter. It sure would be nice if the alignment could be automatic and not involve additional user input.
What I am hoping for would be a way to allow the alignment parameter to do its job when inserting with the following line of
(command "-insert" BLK-N-PTH ins 1 1 rot)
I was catching the rotation value of a "parent" dynamic block by using vla-get-rotation and then correcting for UCS and converting form radians to degrees, and this works well for straight blocks, but some of my blocks are curves and the whole paradigm falls apart with then.
So far my workaround is to have the user also pick the rotation, which does seem to work:
(command "-insert" BLK-N-PTH pikpt 1 1 (while (eq (logand (getvar "CmdActive") 1) 1) (command pause) ))
I have a project in 3D that I would like to export to Stadd. This requires lines rather than blocks. Is is possible to convert the blocks in the attached dwg file to to lines that are centered on those blocks?
View 9 Replies View RelatedI have this snippet that inserts a block “Exit_Arrow”. The block has one attribute. Is it possible to force the attribute to remain at “0” rotation regardless what angle the bock is rotated?
(defun C:Exit_Arrow (/ LA DS)
(setq LA (getvar "clayer"))
(setq DS (getvar "dimscale"))
(C:TTEXT)
(command "._insert" " Exit_Arrow " pause DS "")
(setvar "clayer" LA)
(princ))
Is it possible to create blocks whose attributes remain at "0" rotation regardless the host block's rotation?
I isolated 3 attributes as you can see with my code. My object is too take the value of blkDESC1 and set it as blktag, and then take blkDESC2 and set it as blkDESC1, and erase blkDESC2.
(defun c:aup (/ dxf ent dxf1 ent1) (defun dxf (code ent) (cdr (assoc code (entget ent))))
(progn (if (and (setq ent (car (entsel "
Select an Attributed Block: ")))
(eq "INSERT" (dxf 0 ent))
[code]........
I am working on a lisp file that lets you select a block and automaticaly change the layer and color in block editor. Afther this it exits block editor, deletes the original block and places the new one.
It works fine accept for the last part.
When i incert my new name whit the insert command it automaticaly changes the name whit autofil so it wil still pot my originial block (the new block name is only two characters shorter than the old one).
I had been trying to insert a title block (block) in to a drawing as part of changing the title block But in some drawings the block gets scaled off. Is there any system variable or any solution to maintain the drawing without getting scaled while inserting block.
I had used -dwg units and this appears to single drawings only. Any other way to do this to all the files in a folder.
How to connect to MySQL database and insert data from a set of blocks containing attributes?
Something like:
block 1:
- x coordinate;
- y coordinate;
- handle;
block 2:
- x coordinate;
- y coordinate;
- handle;
block 3:
- x coordinate;
- y coordinate;
- handle;
I've just got the second part (retrieving info from the blocks), but when it comes to connect to the DB I'm completely lost.
For the DB I'm using XAMP for Windows, thus using localhost, user ('user123'), pass ('pass123') and table ('table123'). The table has ID (PriKey and AutoInc), px, py and hdl fields.
I have a block named "WD_MLRH". There are 3 specific attributes which I want to change in it. The attribute names are.
RUNGCNT, RUNGDIST and RUNGFIRST.
RUNGCNT will = 20
RUNGDIST will = 1.0 (or 1 will suffice)
RUNGFIRST will be decided by a user input.
Something along the lines of...
(setq RUNGFIRST (getint "Enter first rung number: "))
I'm sure this is completely wrong, but i hope that portray what I'm trying to accomplish.
I have searched the web and the Autodesk Discussion Group for a LISP Routine that allows me to convert all attributes in a drawing to Layer 0 but i have had no luck. It would be great if the LISP could edit xrefs as well although not sure if this is possible.
**BATTMAN command will take too long for the hundreds of blocks, xrefs and drawings i need to edit.
I downloaded a lisp routine that will align block attributes. The problem is I can only select the attributes one at a time. I'd like to be able select multiple attributes using the selection window or a crossing window, but I haven't had much luck. If you use the AEATTSHOW command, it give you a prompt to "select using window" by pressing W. I'd like to have the same functionality for my Align attributes routine.
Below is the portion of code I currently have to select attributes one at a time:
;* Select all attributes to align with the parent selected above and add the attribute entname and the block
;* entname to a list in format ( (AttrEntName BlkEntName) (AttrEntName BlkEntName) (AttrEntName BlkEntName) )
;*
while (/= TempAttr nil)
(setq
TempAttr (nentsel "
Select Attributes to align: ")
[Code] .........
I have to go through quite a few drawings and extract the attribute vales of the whole drawing and then a subset contained within a couple of polylines.
The whole drawing is Ok as I can use at out or the data extraction, but its the ones contained within a polyline. How do I do that?
How I can modify this code to create a block, ask for a new name for the block, then add the attributes listed inside the code below to the new created block. The lisp does a wonderful job - however, it only works if you already have a block created. We are in the process of drawing components and making blocks one by one, so it makes sense to add the attributes automatically when the block is created. We currently have over 500 components to create as a block and set the attributes to each one by one.
Also I would like to know, If Fields can be used inside the lisp routine. That way we can always have access to the attributes from outside the block and change values for all the blocks at once.
(defun c:addattribs ( / blk def ) (while (not (or (= "" (setq blk (getstring t "
Name of block to update: "))) (tblsearch "BLOCK" blk) ) ) (princ (strcat "
Block "" blk "" not found.")) ) (if (/= "" blk) (progn (setq def (vla-item (vla-get-blocks (vla-get-activedocument (vlax-get-acad-object))) blk)) (vla-addattribute def (getvar 'textsize) acattributemodelockposition "New Attribute 1" (vlax-3D-point 0 0) "NEW_TAG1" "New Value 1" ) (vla-addattribute def (getvar 'textsize) acattributemodelockposition "New Attribute 2" (vlax-3D-point 0 (- (* 1.5 (getvar 'textsize)))) "NEW_TAG2" "New Value 2" ) (command "_.attsync" "_N" blk) ) ) (princ))(vl-load-com) (princ)
I know how to retrieve the entity information from the block, but can't figure out how to write the loop statement to loop, look for first attribute, assign to a variable, goto next attribute, assign to different variable, etc., etc...
In my research, most programs I've seen it execute the loop, assign to a variable, then print/put that data somewhere, loop again and utilize the same variable to print/put the next data somewhere.
I would like each attribute within a block to be assigned a separate variable.
I have an interesting challenge. I am tasked with updating old drawings. The only difficulty that I've run into with the old files are that the TitleBlocks are all done with all of the attributes are named "SPEC". There are 90 attributes. I'm really struggling with getting each attribute's value and then storing the value to a variable so that I can then put that value into a new TitleBlock. The old TB will be deleted to avoid future confusion in the file.
(To clearify, the old TitleBlock is in model space, while there are actually nine new TitleBlocks all in seperate paper space Layouts, and this program may have to run on hundreds of files.)
getting the values from the Old TB. I need them in order of first to last or last to first (either way will work since I have the variable names in a list that can be reversed if necessary.)
simple function to read through the block's attributes in order and store the attribute's value to a variable name in the seperate list (also in order)?
I am testing de new version of autocad 2014 and i have a problem with lisp.
when i use (command "_insert" "block1" pt1 "" "" "" obj1 ).
The block is inserted but without value. In the old version work.Some variable that has to change?