Any routine that will allow to draw a polyline through existing blocks, in the order the blocks should be numbered? Therefore when the sequence has been specified by the polyline then user to define the number system required, and the blocks are automatically numbered in the sequence of the polyine start to finish.
View 9 RepliesI have to go through quite a few drawings and extract the attribute vales of the whole drawing and then a subset contained within a couple of polylines.
The whole drawing is Ok as I can use at out or the data extraction, but its the ones contained within a polyline. How do I do that?
i have created an Autolisp routine that creates a drawing made up of structural members, x-refs & surfaces based on a few different user inputs. I now want the program to insert the drawing as a block rather than individual elements. My Idea was simply to use the block command in the lisp routine to create a block and then have the drawing create itself in block editor, and close once it has done. however I am having difficulty thinking of a way that I can get AutoCAD to automatically name this block depending on other blocks in the drawing, i.e. in sequence. The name is irrelevent really, but it would make sence for it to be logical, so... if the last block inserted was "b7" then the next one should be "b8" and so on.
Is there a better way of doing it all together? I have read a bit into "entmake" but i'm not sure on how to use that function.
I've been trying tons of different solutions to solve this problem: insert a block that has an attribute which happens to be the last object id.
This is the best code I tried so far but without any succss.
(defun c:q1()
(command "_.PLINE")
(while (= (getvar "CMDNAMES") "PLINE")
(command pause)
[Code] .....
I need a function that will allow me to do a "divide" with blocks but I need the single attribute to remain intact.
I need the blocks to align with object and keep the attribute. I did get it to work with constants but the function that I need to run next failed because of the constant. My variable is preset and locked.
i need a vlisp program to draw polyline between two blocks.
View 3 Replies View RelatedI'm using a blocklibrary, where I stored all my blocks, most of them have attributes.
Now I'd like to simplify my workflow and want to update the blocks that I inserted in a drawing trough LISP.
Is there a way to update all inserted blocks and attributes of the whole drawing a once? The idea is, that the LISP checks the whole blocklibrary and updates the inserted blocks that to not match with the once from the library.
We wanted to automatically fill a block's attributes from a selection in Excel. I have a piece of code that has the user select/pick a block to fill. What I want is for the selection to fill multiple blocks in an active drawing. Some of the blocks are the same - which means the same tags/attributes. I've included the code that allows the user to select the block and throws the Excel selection to certain attributes.change the code so that
1) I don't have to manually select blocks - it will find them.
2) One cell (from Excel) will go to multiple blocks - some are same block name.
3) An IF statement that if a certain cell isn't blank/nil
(pretend it would be (nth 21 vl) change DESC11 to XYZ and DESC12 to ABC. For Block namesake we'll call one, BLOCK1 (say it has 3 instances and gets different info in each case) BLOCK2 (say it has 2 instances, also gets different info) BLOCK 3 AND 4 both have an attribute - DESCAA1 that gets different info from Excel.
(defun C:AUTOFCM (/*error* adoc attribs blkobj enExcelapp Sel Sht Rng vl Wbk ) (defun *error* (msg)(if adoc (vla-endundomark adoc)) (if (and msg(vl-positionmsg '("console break""Function cancelled" "quit / exit abort") ))(princ msg)(princ "Error!") ) gc) (princ) ) (or adoc (setq adoc (vla-get-activedocument (vlax-get-acad-object))) ) (vla-startundomark adoc) (alert "Select a range of cells in Excel.") (setq ExcelApp (vl-catch-all-apply (function(lambda ()vlax-get-or-create-object "Excel.Application") )) ) ) (if (vl-catch-all-error-p(setq Wbk(vl-catch-all-
[code]....
Is there a routine that I could use to count the blocks that are in a closed polyline? The blocks may have or not one or more attributes.
In a previous session I saw a routine which was counting the blocks which had attributes in them, but it doesn't really work, because some of the blocks dont have attributes.
Also is there a routine that counts the different texts that are in the same polyline?
i am trying to restrict users from modifying certain attributes in a block,i can create the blocks with some of the attributes on locked layers, but then autocad pops up an annoying alert box, is there a way to disable this? the other option i can think of is to redefine the commands *ddedit, *attedit, *ddatte,*attipedit,
View 5 Replies View RelatedI need a lisp code to burst all "blocks with text/attributes inside" in selected area. That means user should select an area (window selection) and lisp program should be find all blocks with TEXT or ATTRIB inside in selected area and then applys "BURST express tools" command to all these blocks in the selected area by user.
View 9 Replies View RelatedThere is a quick way to remove all attributes, including in nested blocks. Looking some lisp in the forum, I can't find one code for remove this elements completely.
View 9 Replies View RelatedHow to create a lisp to automatically export attributes from selected blocks to defined txt file without having to everytime confirm the file name, location and if the file shall be replaced?
Meaning is that I often export attributes to txt file for further use. It is always the same file (I just overwrite it always).
The way I do it now is selecting blocks, using ATTOUT command, then going to the desktop, selecting ATT.txt file and confirming that it is to be replaced.
Is there a way to make lisp or script that will just do all it in at once?
I found on forum such a lisp as below, but it exports all ablocks on drawing and it exports to txt file which is located in same place as drawing and with same name as drawing. Tried to modify it but without success:
(defun cut-att ()
(load "attout")
(setq fna (strcat (getvar "dwgprefix")
(acet-filename-path-remove (acet-filename-ext-remove (getvar "dwgname")))
".txt"
))
(setq ss (ssget "X" '((0 . "INSERT") (66 . 1))))
(bns_attout fna ss)
)
Same question for ATTIN - I use attin and always same file name from same location - how to automate it with one command?
I am looking for a way to create a master list of construction notes then use blocks attributes with fields to link to that master list. That way if the master list changed the note bubbles would change as well.
Sheet sets are being used with this project but I can't think of a way to make it work with the existing sheet set technology.
I would like to take all the vertices out of a multiple-vertices polyline so that it reduces to just its start and end points, can this be done?
View 4 Replies View RelatedDue to modeling purposes, I need to convert a 3D polyline to a spline. What I have been doing is:
- change polyline fit/smooth to cubic from properties
- convert polyline to spline by typing spline -> object
- method -> fit from properties
You can see the original 3D polyline (green) and the resulting spline (magenta) in the attached drawing.When I zoom in and measure the distance between the two entities at different points along them, at some points the perpendicular distance exceeds 5 millimeters, and I want to ensure the deviation remains under 1 millimeter or even less.
I know I can change the knot parameterization of the spline, and this does work at some locations, but the difference increases at others.Why is there a 5.6 mm difference between the spline fit point and 3D polyline vertex, as measure in the attached drawing?
Now, I can go and manually stretch the fit point to coincide with the vertex. Also, I can add fit points between existing ones to drag the spline closer to the original 3D poly.
However, some of my polys are really long, and it is very time-consuming to do this manually while measuring points along the entities to make sure the distance stays small enough.
how to automate this process? For example a lisp that would maybe take the original vertex points, add say maybe 3 (not too many) new ones between them, and then generate a spline while making sure the deviation is less than the set value of 1mm? I am using AutoCAD 2013.
How can specific attribute values be extracted from a drawing and assigned to a variable in lisp.
The existing title block is having attributes : Area, Sub area, Description, Drawing type. I want to extract this values and assign it to some variable which I have already listed and then it shall be assigned to some other attributes in the same drawing with Area1, Subarea1, Description1, Drawing type1... and so on.. Both the attributes shall be in the same drawing file.
how to write a LISP that enable me to direct automatic rename multiple block name?
Example is i have 3 block names as " A123 " , " A728 " , " A003 "
When i activate the LISP, it will automatic rename the block name to be " CAD1" , "CAD2" & "CAD3", whereby
the word "CAD" i can change whenever i start to use it change multipld block name.
(defun CELBLKS ( / e blk ss blkl)
(setq blkl "" ss (ssadd))
(while (setq e (entsel "
[Code]....
i have this lsp, it works great but how can modify it if i want select with a window.? exemple: if i have 3 differentes blocks, i want to select them with windows and the lisp select all blocks that are identical of those 3.?
I have a project in 3D that I would like to export to Stadd. This requires lines rather than blocks. Is is possible to convert the blocks in the attached dwg file to to lines that are centered on those blocks?
View 9 Replies View RelatedI have this snippet that inserts a block “Exit_Arrow”. The block has one attribute. Is it possible to force the attribute to remain at “0” rotation regardless what angle the bock is rotated?
(defun C:Exit_Arrow (/ LA DS)
(setq LA (getvar "clayer"))
(setq DS (getvar "dimscale"))
(C:TTEXT)
(command "._insert" " Exit_Arrow " pause DS "")
(setvar "clayer" LA)
(princ))
Is it possible to create blocks whose attributes remain at "0" rotation regardless the host block's rotation?
I isolated 3 attributes as you can see with my code. My object is too take the value of blkDESC1 and set it as blktag, and then take blkDESC2 and set it as blkDESC1, and erase blkDESC2.
(defun c:aup (/ dxf ent dxf1 ent1) (defun dxf (code ent) (cdr (assoc code (entget ent))))
(progn (if (and (setq ent (car (entsel "
Select an Attributed Block: ")))
(eq "INSERT" (dxf 0 ent))
[code]........
I have an opportunity to make a good impression at a new job, but ive never had the initiative to learn how to write a lisp routine. at my work we make walk-in coolers and freezers. these coolers are modular with a standard wall piece measuring a certain length. these wall sections have to be numbered sequentially. is there any way to automate this? sometimes we get change order from the client and it means going back and manually changing multiple texts (sometimes in the hundreds), but i thought if there was a way these wall sections could be scheduled somehow that when a new wall panel is inserted in the beginning of the sequence it would update everything after it automatically.
View 9 Replies View Relatedthis is a Offset cutting plane line I want it to be all polylines but I can't get the ename of the end points of the polylines dose anyony know how
(defun ccp (/ pt2)
(SETVAR "CMDECHO" 0)
(setvar "angbase" 0)
(setvar "angdir" 0)
(command "polarang" 1)
(setq pt1 (getpoint "
[Code]....
Is it possible to determine the sum of the lengths of all of the polylines on a certain layer? I'm trying to determine the total length of joint sealant on a building's exterior.
View 8 Replies View RelatedI am using acad 2010. I have a contour generator that uses 3d polylines to make contours. I get depressions or tops where I don't want them. I need a lisp routine that will allow me to adjust the z value only on any 3d polyline. I need to raise or lower the z value at any vertex and repeat if necessary. I don't need to prompt the user- I am the user.
View 2 Replies View RelatedI create contour line in TOPOGRAPH program, and I import these polylines to AUTOCAD. I have to set elevation for each polyline manually, and I waste a lot of time doing that.
So looking for lisp doing that automatically. I mean, invoke the command, set the first elevation and them select the polylines.
e.g. The first elevation is 530. The next polyline that I select is 531 and so on.
For the sake of editing, I sometimes make LWPOLYLINES and convert them to regions so that I can union and subtract and intersect, etc.
then sometimes, like now, I want to work with them like as LWPOLYLINES again.
is there some command I don't know, or some routine or shall I make one?
I need to get the layout list in reverse order. How to do this? My plotter outputs prints face up and I wind up with a stack of drawings in reverse order - If I can cycle through the tabs in reverse order they will wind up in the correct order in the print room!
View 9 Replies View RelatedI have a block named "WD_MLRH". There are 3 specific attributes which I want to change in it. The attribute names are.
RUNGCNT, RUNGDIST and RUNGFIRST.
RUNGCNT will = 20
RUNGDIST will = 1.0 (or 1 will suffice)
RUNGFIRST will be decided by a user input.
Something along the lines of...
(setq RUNGFIRST (getint "Enter first rung number: "))
I'm sure this is completely wrong, but i hope that portray what I'm trying to accomplish.
I have searched the web and the Autodesk Discussion Group for a LISP Routine that allows me to convert all attributes in a drawing to Layer 0 but i have had no luck. It would be great if the LISP could edit xrefs as well although not sure if this is possible.
**BATTMAN command will take too long for the hundreds of blocks, xrefs and drawings i need to edit.