I have this code to make fillet to a polyline, but the command does not allow specify fillet radius. How I can change the routine?
(defun C:filletv ( / ent ) (setvar "FILLETRAD" 2.500) (if (setq ent (entsel "
Select element near vertex: ")) (command "_fillet" "_P" ent) ) (princ) )
I have been having a few 3dpline's with the last vertex being in a different layer. I saw a site mention that this is an AutoCAD 14 bug that could be caused if a program does not end the pline with the layer being set properly before doing a seqend command. If I move the entity to another layer and then back to the correct one it will fix it. Audit in R14 will not show any errors. If I export the file to AutoCAD 12 , audit will detect and fix the problem. I would like to find a Lisp, ARX, etc. that would check for this problem and fix, change color or layer, or whatever.
View 2 Replies View RelatedI have a program that makes 3d polylines from various data. That 3d pline then gets added to a civil 3d surface as a breakline. I want to modify the pline with my program, but preserve the handle, as I think that is what C3D uses to decide if its part of the surface. I tried this as a sample with no luck:
;DELETE 3RD VERTEXT FROM 3D PLINE
(DEFUN C:T3 ( / EN ENAME ENT ENTL)
;GET 3D PLINE
(SETQ ENT (ENTSEL "
Select 3D Pline:")
[Code] .....
I know you can modify a vertex, but what about add and delete with entmake and entmod? I also considered using activex for this task, but you can only add verticies from what I could tell in the object browser of VBA, not delete them.
What I will be doing is deleting all the verticies and adding back the correct ones. Or if there was a way to transfer a handle to a new entity after deleting the old, that would suffice too.
I have LWPOLYLINEs that represent a cross section of a train tunnel. Each LWPOLYLINE lists its 2D points in an Object Coordinate System.My task is to create 3D Polylines in WorldCoordinateSystem using those LWPOLYLINEs.I have posted a drawing with sample objects.
I have attached a sample drawing. Drawing was created with Civil 3D 2013, but I exporttoautocadr12dxf'd it and then save to 2004 dwg so most should be able to open it.
I am looking for an AutoLISP routine, which gives all aligned dimensions of a closed polyline, drawn in 3d.
I have attached a 2D drawing for reference.
Is there anyway to use LISP to list the x,y coordinates of a pline?
View 3 Replies View RelatedIn continuation with thread All to Pline . I want to add one more function to this lisp i.e. Join all the objects selected.
Can this be done?
I tried this:
(command "_.pedit" "m" ename "" "j" ename "")or (command "_.pedit" "" "j" ename "" "")
But it gives me an error something like this:
Requires numeric distance, two points, or option keyword.
; error: Function cancelled
Enter fuzz distance or [Jointype] <0.000>: j
Enter join type [Extend/Add/Both] <Extend>: *Cancel*
or
Command: ch2pl
Select objects: Specify opposite corner: 5 found
Select objects:
*Invalid selection*
Expects a point or
Window/Last/Crossing/BOX/ALL/Fence/WPolygon/CPolygon/Multiple]:
; error: Function cancelled
Select polyline or [Multiple]:
Enter an option [Close/Join/Width/Edit vertex/Fit/Spline/Decurve/Ltype
gen/Reverse/Undo]: *Cancel*
Command: Specify opposite corner:
Command: *Cancel*
Is there a function to obtain the start angle and end angle of a pline, i know arcs do.
View 4 Replies View RelatedI have been using one routine very successfully to create a pline in modelspace that has the outline of the chosen viewports in the drawing. This one works great.
Now I am trying add other routines that I've done to better fit my needs. If I use each routine individually at the command line they work, but when I use all in a single command I got the following errors:
The routine SetColor - does not change color to Bylayer The routine RectWidth - ; error: bad SSGET list
Why?
See the attached file for more details and be free to improve whatever you want in my routines because they are very basic.
And, if I am not asking to much, is that possible to not be prompt to select objects? I mean, the routine could automatically select all viewports in the drawing...
I have plines of circuits that sometimes have T's (line goes along, then T's out then back to T point and then continues).
Here is example line -
(setq List_Pline (list (list 0 0) (list 1 1) (list 0.5 1.5) (list 1 1) (list 2 2) (list 3 3) (list 3.5 2.5) (list 3 3) (list 4 4)))
nth 0 = (0 0)
nth 1 = (1 1) - T point
nth 2 = (0.5 1.5)
nth 3 = (1 1) - T return point
nth 4 = (2 2)
nth 5 = (3 3) - T point
nth 6 = (3.5 2.5)
nth 7 = (3 3) - T return point
nth 8 = (4 4)
I need to be able to pick 2 points along the line and find the shortest route.
Examples -
1st point at 1,1 and 2nd point at 3,3 - new line is nth's 3,4,5
1st point at 0,0 and 2nd point at 1,1 - new line is nth's 0,1
1st point at 2,2 and 2nd point at 3,3 - new line is nth's 4,5
1st point at 3,3 and 2nd point at 4,4 - new line is nth's 7,8
1st point at 0,0 and 2nd point at 3,3 - new line is nth's 0,1,2,3,4,5
1st point is 1,1 and 2nd point is 1,1 - new line is nth's 1,2,3
I've tried using vlax-curve-getParamAtPoint, but it returns 1st T point.
Synopsis of program -
Select Pline
Pick 1st point
check if on line
Pick 2nd point
check if on line
check if 2nd point is before 1st point, if so swap locations
find last nth of 1st point
find 1st nth of 2nd point
return list
Now I have all block instances rounded into a 5mm-accuracy. How to also round in Line start and end points (and maybe even polyline vertices) into a 1mm (or custom) accuracy. There are hundreds of inaccurate line elements within the drawing .
View 4 Replies View RelatedHow to change the ltype in a PLINE drawn whith this
(defun c:cordaluminosa ()(if (tblsearch "LAYER" "Elétrico - Luminotécnico")(command "_.-layer" "_THAW" "Elétrico - Luminotécnico" "_ON" "Elétrico - Luminotécnico" "_SET" "Elétrico - Luminotécnico""")(command "_.-layer" "_MAKE" "Elétrico - Luminotécnico" "_COLOR" 3 "" ""))(command "._pline")(while (wcmatch (getvar "cmdnames") "*PLINE*")(command pause)))
I want to set the ltype FENCELINE1 to this object.
what I am attempting -
Pick a line
Pick a starting point on the line
Pick a ending point on the line
Pick side to offset
create list of offset points
Create a new line with a offset
I think I could do this using brute force, but would prefer a mathematical solution.
the resulting arc-fit pline has each pline segment converted into two arcs, the common radii of which are perpendicular to the original segment (unless direction of curverature changes)
the resulting arcs can be calculated given the angle of the tangents for each segment.
the factors for determining the tangents at vertex N are:
deflection angle at N
deflection angle at N+1 (90° or non-extant = not a factor, 0° or 180° = segment is the tangent)
deflection angle at N-1 (90° or non-extant = not a factor, 0° or 180° = segment is the tangent)
ratio of lengths of segments (N , N+1) and (N , N-1)
I can find the tangents when N±1 = 90° and when the segment lengths are equal but i can't figure out how to compute the tangent if these 3 factors are varied.
I don't want to use (command"._PEDIT" pl "_FIT""") because i need to collect the arc data anyway and at a high frame rate. The data will be used to further compute a spline frame that best fits a quadratic spline to the arcs. That part i know how to do!
I have this routine for using a selected arcs rad value as a new fillet rad. If you like, a "match fillet" routine:
;Fillet Copy
;Copies the Radius of an Existing Fillet or Arc;
(defun C:filletcopy ()
(setvar "cmdecho" 0)
(setq c1 (entsel "
Select Fillet to Copy:"))
(setq c1 (entget (car c1)))
(setq rad (cdr(assoc 40 c1)))
(setvar "filletrad" rad)
(princ "
Select Lines:")
(command ".fillet" pause pause)
)
I use the routine loads but could modify so it would pick up the value of a filleted polyline? As it stands it can only select an individual arc. I would like the routine to be able to pick individual arcs and/or filleted polylines, without exploding first, if possible....
I need to change the color of all lines/plines that intersect a given pline. How would I go about making the selection set of all lines that intersect that given pline.
View 8 Replies View RelatedI've been searching on and off all morning for a lisp routine, without any luck. I'm trying to draw a pline with a pre determined width (5") and be able to draw unlimited line segments then automatically fillet with a pre determined radius (5").
I wrote this generic macro: ^C^CPLINEWID;5;PL;\\;FILLET;R;5;F;P;LAST; to save SOME time but I want unlimited line segments. Can this be modified or would a lisp be the better route to go?
There are a ton of lisp to match text rotation to a selected line, but not vice versa.
View 9 Replies View RelatedI am using acad 2010. I have the ability to draw a 3d polyline on the screen with a different xyz value for each vertex using a digitizing puck. I need a lisp routine that will allow me to adjust the z value only (not the x and y values) on any 3d polyline. I just need to raise or lower the z value at any vertex and repeat if nessasary but I don't want to type it in, I want to raise/lower the z using digitizing puck (with z wheel)....example: I draw a 3d polyline which has 9 vertices with different elevations - vertex #6 is 22.6 (too high) in the z value so I need to drop it to 22.4 without typing it in. Vertex #8 is 12.2 (too low) so I need to raise the z to 12.6 without typing it in and using the z wheel on my digitizing puck. Others have tried and but this is a bit complicated and I may have not expressed it correctly.
View 2 Replies View RelatedIt's possible make a fillet with window selection?
View 4 Replies View RelatedI have a lips that creates a zero radius fillet.
(defun c:FZ () (setvar "FILLETRAD" 0)(command "_.fillet" "multiple"))
This works great.I would like to expand this by turning the line into a polyline..
I need to wright a routine in autolisp that selects all 3Dpolylines with the same vertex Z value.Qselect as no transparent mode and filter doesn't work.
View 7 Replies View RelatedI'm looking for something that, after selecting several plines (overlaped or not), I can insert/remove vertexes.
View 9 Replies View Relatedhow I can add in some vertex's at regular intervals on a fline or pline?
C3D 2013
Is there a lisp that will allow me to do a continuous dimension, but will alternate the dimension position from low, high, low and high? If there is no lisp already created, how to create one?
See Continuous dimension attachment for example.
I work at a glass and glazing company and this is how we dimension mullion width and DLO. See typical window dimensioning attachment for window elevation with dimensions.
I have a list ("temp.dwg" "temp2.dwg") and would like to add the string "insert text here" into each item in the list resulting in ("insert text heretemp.dwg" "insert textheretemp2.dwg"). how would i go about doing that using LISP?
View 2 Replies View RelatedIs there a way to programatically set a visual style before a drawing actually opens?
We have some huge models and people seem to forget to change their visual styles back to 2D wireframe before saving and exiting drawings. Some models will crash on some workstations when trying to open in a rendered mode.
I found a lisp with a function that looked to set viewport visual styles. But it does not seem to be supported anymore. --> (vla-put-VisualStyle vport 1)
I'm trying to write a lisp routine that, when I invoke the mleader command, osmode is set to "nearest" & orthomode is set off. I then would like the original settings to be returned.
attached is what I have written so far:-
Lisp that switches back on Selection Preview i.e. thickens and highlights lines when you hover over them?I don't know why, but they are always unticking the boxes.
View 4 Replies View RelatedIs it possible to execute a certain command based on multiple selections withinin a dcl? for example: two radio colums, one with selections A and B, and a second with selections 1 and 2. is it possible to program commands based on user selections from each column? ex: if A and 1- do a command. A 2- do a different command, etc...
I tried :
(action_tile "key1" "(setq A t")
(action_tile "key2" "(setq B t")
(action_tile "key3" "(setq 1 t)(done_dialog)")
(action_tile "key4" "(setq 2 t)(done_dialog)")
(if
(and (a) (1)
)
(command ...
but was unsuccessful. no matter which combination was selected, the command under all combinations would run.
I am trying to find a lisp that would get an attribute value (tag name = NBR_5) . I'm trying to run a simple routine that would let the user place the value from the titleblock attribute as text on a drawing. I see a ton of articles regarding getting attributes but I am not well versed in programming.
View 9 Replies View Related