Normally I plot in paper space and everything works well. when I plot in paper space all the lines ae much, much lighter and almost invisible, whereas if I plot the same drawing in model space the plot comes out perfectly, though not in scale. I must have pushed a wrong button somewhere but wnat button is beyond me.
View 7 Replies
If I import an Arcview shape file into Autocad Map, why can't i plot it out from Paper Space??? I can plot out shape file data in Model Space but not Paper Space. The data is mapped to a layer, and it can be viewed in "Print Preview" but nothing comes out when i plot from paper space.
View 2 Replies View RelatedWe have a T790 44in, with 42" roll paper installed.
The thing I'm having trouble with, is getting it to act like it has roll paper. I can set custom paper sizes in the printer drives all day (such as 42" x 42") but this is only half way accurate, and can waste a lot of paper.
Is there a particular way to set the printer to use the roll paper?
This is an issue for which no one in my office has any solution. We create all of our plan sets on E1 size paper. However, when we plot them for redlines we print to C-size to save paper. I know you can "publish selected layouts" to plot numerous tabs at a time. However, I am unable to figure out how to make them plot to a smaller size paper than what the page is set up for. Is there a way to plot all of the tabs at a smaller scale without plotting each tab individually?
We just recently upgraded to AutoCad 2014.
2 of 3 viewports in paper space do not show up in print preview, nor will they print. The viewports are all on the same layer, defpoint layer. Even if I create 3 new viewports and erase the old ones, still can only print preview one viewport and only one viewport will print.
View 6 Replies View RelatedHave a dwg with two layouts sheets that print to pdf in paper space - one layout works just fine the other NOT.
Both include one view port and a few small details as pdf underlays(@ 150 kb each) in the PAPER space layout.
The problem sheet - ran a very slow plot preview but it did complete a full view of the layout, then when selected to do the plot it never completes the pdf.
I tried a pdf plot of the same area in MODEL space and it previews just fine and plots to a pdf just fine.
I've run into a small problem while trying to export a drawing from paper space as a PDF. The drawing is of an electrical panel for a product. The panel is rather large, but the drawing includes some smaller details, such as a vendor logo on a component or a few extra lines on the border of a display screen. We have a large, multi page PDF file that uses A4 paper size that I need to insert this drawing into, so the export must be at this size. When exporting, I have CAD set to use monochrome and ignore the line weights, which solved my initial problem that the parts would show up as solid black splotches.
Now that the back story is over, here's the problem. When I export the pdf, everything looks great except these small details around the components. For some reason, the lines in the components will shift to one side or the other, causing breaks between features. Most of these breaks occur between an arc endpoint and a line endpoint. The export also excludes some smaller bits of geometry.
When printing a paper space viewport in Conceptual Visual Style mode, text objects are visible in the print preview but not in the printout on paper. Why are they not hidden in the preview if they are not going to be printed?
View 2 Replies View RelatedSo I have the educational version of ACAD 2012 and this is my first time using that version. My model is done and I formatted my layout with a border and the model to scale in the viewport. When I go to plot to PDF, all I see is the border. I've tried fiddling with colors and viewports but neither of those did anything.
View 3 Replies View RelatedI'm trying trying to plot something I just drew. I'm plotting from paper space and all the text and objects that are in paperspace come out under everything in the viewport that's their. I have tried display order but it doesn't seem to work; when you look at it on the screen the paperspace objects look like they are on top but when I plot it they come out underneath.
How I can fix this without moving everything into model space?
I have created some rectangles with a solid fill hatch in paper space in different colors, on different layers., when i plot them, they plot in black. what can i have checked or not checked to solve this? the viewport that i have in the layout plots in color, i am using the acad plot style.
View 9 Replies View RelatedI am trying to print a tall, thin window, auto-scaled to fit on 11x17 paper using a Windows PC3 driver. I want the image to be essentially 17" tall. No matter what paper orientation I choose in the printer Properties (Portrait or Landscape), the image is rotated automatically the wrong direction. (The print preview shows the paper rotated as Portrait or Landscape correctly, but the image is always rotated to fit the 11" dimension of the paper). I'm using AutoCAD Electrical 2008.
View 3 Replies View RelatedI have several objects on various layers in model space and they are exposed through a viewport in a paperspace layout. I also have a corporate CTB plot style.
Here is my problem: If i plot the objects from model space, they all plot with the correct lineweights as defined in our corporate CTB, but when i plot them from the paperspace layout, some but not all objects plot with a heavier lineweight than what is defined in the CTB.
I thought the CTB was supposed to override any settings applied to individual objects, but more importantly, why the different results, on the same objects, depending upon the space from which they're plotted?
I have been having this issue for a few weeks, where my contour lines will not plot in paper space, but the labels do. If I plot from model space everything shows up. All layers have been checked and nothing is frozen or turned off in the viewport.
View 3 Replies View RelatedI have a canon ipf605 plotter. I try to plot to a custom paper size with the "plot transparency" and it doesn't work.
View 3 Replies View RelatedI've created a drawing in model space, added text in paper space. When I go to plot the drawing the text is rotated 90 degrees instead of staying oriented the way I added it. There must be some setting that I am missing somewhere!
View 9 Replies View RelatedHow can I do this?
View 4 Replies View RelatedIve got a A3 drawing all set up to plot to my printer and it works fine.
Unfortunately the same cannot be said when I use the _exportpdf command (or the PDF function in the ribbon):-
- If I export using the current layout then the top and bottom of my title block are chopped off.
- If I change the paper size to A3fullbleed then it does plot the whole drawing, but not to scale (even though its still set to 1:1
- Changing to the other A3 options goes back to chopping off the top and bottom.
From my limited knowledge It appears that the columns need adjusting, trouble is, i'm not sure how?
I'm using 2004lt- I have current .dwg in modelspace and set up to plot in PS@ 3/23"-1'-0". I'd like to create a second set of PS tabs to plot portions at 1/4"-1'-0" on the same border when needed.
In its a single viewport in MS and PS the current scale is 1:1 but if i change it to 1/4"-1',etc the plot preview appears wrong
Is there a way to set the Dwg to Pdf.pc3 so that when I hit plot, it "knows" to save the pdf in the bloody folder that the source .dwg file is located....I can see how to set it to 1 single default folder in Options ( i.e. my main Clients folder) but really, how to get to to plot to the source folder..... has got to be less than 1/2 hours worth of coding....I get pretty tired of browsing/scrolling etc to where I want the pdf to end up.
View 2 Replies View RelatedMy computer crashed. Fixed it, but when I use "Cutewriter" now, it doesn't show
the different line weights.
it seems that it doesn't pick up the different weights.
am using ACAD2008 on windows XP. I have just started having this problem that if I choose to plot from a window the plot dialogue box locks up after the window is selected and the command line is still asking for the corners of the window to be selected. But everything plots ok if I use extents.
View 2 Replies View RelatedWe use several different printers at our company, and one thing that I find really bugging is that I have to change the plot settings on each sheet, if the file has been worked on by someone else.
Is it possible (for example) if I've got 7 sheets set up, they all have an A3 drawing set up (correct extents, pen settings etc), for me to highlight all of the tabs and just change the printer? Rather than going into each sheet and manually changing them?
We've got an HP Designjet 455C attached to an SBS 2003 computer.
From Autocad, I can print when I set the page size to A4 - as expect, it prints a nice A4 sized plot on the A1 width roll. But if I try to print full size plots, nothing happens; the document spools, but the printer does nothing.
It must be something to do with paper size or orientation, but I can't find what. I wondered if there was anything well known I should try (I'm not that familiar with Autocad - yet).
Part of the problem was inconsistency.. sometimes test documents would print, and then they wouldn't! I also got one which seemed to print at the right size, but was only printing part of the file content. These are existing Autocad files, with a printer that has been working in the past.
Two of our computers have windows 7 and we are unable to publish or if we plot we have to wait until that page is completed before sending another page otherwise only some the information shows up when printed (ie. no dimensions or no title block). This does not happen on the other computer in the office which still has windows XP.
View 2 Replies View RelatedI am finding that my DWF files sent to the plotter are plotting with the linework being heavier than the same file sent directly to our plotter. These are just lines that should plot with a narrow width (ie walls on a floor plan) but they seem to be about twice the width and hence look "darker". Is there a setting that I am missing or some other way to get the lines to plot out thinner? Also, TTF fonts plot thicker in DWF. I've tried the various options in the DWF viewer when sending to the plotter, but none seem to work.
View 6 Replies View RelatedI have an issue with plotting line thickness, when I use the company setup using a d-size B&W.pc3 and mono chrome.ctb files, i can't seem to get the plotter to show line thickness. But using the same setup with a customer border, I can get the line thickness.
Also I not sure if this makes a difference, but the company plots from model space and where most of our customers use paper space.
Years ago, there was a program of routine that would plot files to a sheet resembling a photographer’s contact sheet. You would tell it which folder to use and it would print the entire folder. You could tell it how many rows and columns and it would fill up the 8.5 x 11 or 11 x 17 sheet with little images of the files.
View 2 Replies View RelatedI am trying to plot a layout sheet 24'' W x 18" H. The frame on my sheet is 22''W x 16''L (inside the dash lines limits we see on the layout). I believe I prepare the print correctly:
- Select the printer (HP DESIGN JET PS)
- I use the window fonction to select the printable area ( left upper corner and then the opposite corner).
- Select Paper size Arch C (landscape)
- Paper orientation: Lansdcape
The preview shows that the upper and bottom lines of my frame will not print, and they do not, even if I try (see the attachement below).
Is this a driver problem?
I have a Dell 515 plotter printer connected to a network computer. I can print to it from other programs, but as of this evening, when I select the printer, the screen goes white and autocad dies. I can print to a pdf or even select another printer that is not even turned on. This also happens when the 515 is set as the default and I select print to default system printer.
this has happened before and It seemed like a lucky fluke that i got it to stop. something about the order of change scale, preview, change plotter etc, but no luck this time.
I have a bunch of pdf underlays in model space with four viewports referencing them in one paperspace layout. The viewports are on their own non-plot layer and the pdf underlays are on a plottable layer. This isn't an issue on the original dwg that I copied them from.
-Everything appears fine in paperspace (see FIG. 1)
-When I go to plot, only the viewport on the right shows up. (see FIG. 2)
-If I move the viewports on the left to the right side, they plot.(see FIG 3)
-When I move the original right viewport to the left side it no longer plots. (NOT SHOWN)
-If I toggle each viewport in the original layout and draw a random line in model space all four of them plot(see FIG. 4)
-I've checked the vp and pdf underlay layers and properties-all are good
-I've tried creating new vp's and still have same issues
-tried creating a new dwg, copied in the pdf underlays and still have same issue
