I was wondering if it is possible to measure the total length of lines I have in one layer without using the measure tool on each individual line. In searching other posts a lot of answers reccomend using LISP. Since I am not familiar with LISP at all and haven't purchased the add on is there a simpler way using AutoCAD LT?
View 2 Replies
In an attempt to aid purchasine I have started adding a length and width parameter to our models. These parameters are converted to a purchase parameter either in square feet or per foot length depending on how the material is purchased. I would like the paramater to also automatically update if the part size is changed. I now come to a part made of a round shaft that is bent and am looking for a way to get an accurate length for it. The part is made with a sweep and the square corners are radisuesd in the sewwp. I could pull the three dimensions in the sketch and add them together to roughly appeoximate the length but that would not be quite accurate. As the number I come up with will also be used by fab to cut the rod before bending I would like it to be correct. Is there a way to generate an accurate length that can be saved as a parameter? In SWx I would create a datum axis in a sketch that could be used but I am not seeing how to do that here.
View 9 Replies View Relatedwell i have a homework for the exams and i have no time,The question is, how i can measure the exact length of an arc (or a polyline) ? See the pic. ghrrhhr.JPG
View 3 Replies View RelatedIs there a tool where you just click on any line and it tells you how long the line is from end to end?
Basically I am drawing a curvy line that twists and turns here and there, but the line has to be less then so long. So I have to approximate the length by doing strait measurements and multiplying, it's really a pain.
I'd much rather just click the line, and it tell me how long it is from end to end, across turns and rounded edges and corners.
How can i get the length or diameter of a cylindrical face by selecting the face as shown in the attached picture.
View 4 Replies View RelatedIs there any way to quickly measure the perimeter of a part, and also measure the length of any circles?
Our estimator is taking the drawings supplied from the customers and needs to quickly know what the cut length is around the part, and then also know the cut length of all holes or internal openings.
Lenovo Think Pad
Windows 7 SP 1
64 Bit.
Inventor 2013
ACAD Mechanical 2013
I have just started to use ilogic, what i want to do is measure the length of a loop in a sketch and then use this measurement as a parameter.
I have found this rule that will measure the loop length and display it in a message box
Dim se As SketchEntity = ThisDoc.Document.ComponentDefinition.Sketches(1).SketchLines(1)
MsgBox(ThisApplication.MeasureTools.GetLoopLength(se)*10 & " mm")
but i do not know how to capture the measurement as a parameter .
I am trying to create a iLogic Rule that will measure the Length, Width and Thickness of a part and ut it into the custom fields we have. I am having a hard time remembering how to get it to do it from the assembly level. I want to run this on the assembly and have it populate all the parts inside of it. The code below will do it for a part but what is it I add to get it to drill down into the assembly?
iProperties.Value("Custom", "THICKNESS")=Measure.ExtentsHeight
iProperties.Value("Custom", "WIDTH")=Measure.ExtentsWidth
iProperties.Value("Custom", "LENGTH")=Measure.ExtentsLength
Then I want to add this formula to the Stock Number iProperty = <Length> X <Width> I can get it to add the values but I can not get it to add the formula to the stock number.
how to measure the length of a path in Photoshop CS ? Or is this impossible?
View 5 Replies View RelatedI'm working in laser cut and very often I need to know how long is the path I'm going to cut with my laser machine. It is very useful to know the length (and the area) of each path while you're designingin Illustrator. I know you can already measure lines or whole objetcs, what I mean is to know the exact path lenght of the lines included in a logo, for exemple, or in a complex drawing.
How I could get this informations in Illustrator CS6?
I have selected several lines (not pl or spl), just lines, all of which are the same layer and such. I want to be able to select all thirty or forty of the lines using either the select similar (lisp, AC2010) or quick select and return a total length of all of the selected lines. In the properties box it shows as varies.
View 2 Replies View RelatedI'm using paint.net ver. 2.6.
I'm trying to measure length using the grid and viewing the image in its "actual size", but 'm getting a wrong value (e.g. 3cm instead of 1cm).
Is there a correct way to measure length in paint.net?
Several people recommended DIMANGULAR. I have some concerns using this method because it is dependent on the precision of angular units in the drawings DIMSTYLE settings. For example, if a drawing file's DIMSTYLE has a precision set to the nearest whole decimal degree or only shows degrees and minutes but not seconds then the angle may appear at a certain angle, let's say perpendicular at 90 degrees. But in reality the angle might be slightly less than 90 degrees, if its off by a few seconds.
I learned an alternative way by selecting both lines and typing the LIST command. The Angle in XY Plane will show the measurement for each segment in bearings, not azimuths. I simply find the difference between the Angles in XY Planes for both lines to determine the angle. I have a few concerns with this method.
1. How do you add subtract bearings measured in degrees, minutes, and seconds? For example, N 76d3'18" W and N 13d56'42"E? I "think" there are websites that can do this? Can this be done directly in AutoCAD through QuickCalc or some other tool?
2. Lines, but not polylines, have Angles in XY Planes in the LIST command. Is this because AutoCAD assumes that polylines will be composed of more than one segment (and each segment with a possible different angle)? Is there anyway to measure the angle of a single one-segment polyline?
Is there a DIFFERENT way between the two methods I just described to measure the angle between two lines (and two polylines) in AutoCAD?
How to acurately measure the angle between 2 lines (or defined by 3 points) in illustrator?
View 6 Replies View RelatedI have Photoshop cs6 extended addition and was told Photoshop would work for the research application I need but so far I am finding it very difficult to do what I want. Basically, I need to be able to measure multiple lines (the red ones in the screen shot) of an image precisely, and make sure that the lines I measure are documented so that they are actually visible (so not just with the ruler tool) on the screen and labeled.
See image for example. I need the lengths (converted with the 2 micrometer scale at the bottom of the image). When I use the info, it gives me the lengths, but I can't save them, or look them up at a different time. Also, when using the line tool, then doing the "record measurement" it does not give me the length of the line but insted acts like it is a thin rectangle and gives me a height (which does not seem to be the same as if I used the measurement tool and put it next to the line, which is an idea I have, but not as accurate) and a width.
I use it to measure angles of micrographs (images taken with a microscope) --- the angle measure tool is great, and easy to use! I would like to be able to save the angle measure "rulers" into the image, for documentation purposes. Is there a way to incorporate the angle "ruler" in a layer or overlay in the image so that I can save a new file with the ruler "burned in" (for lack of a better term).
I will also be adding the text of the resulting angle measurement --- it would be cool if the result of the angle measure could be automatically added as text to the image (preferably in a different layer than the original image). I can type it the result with the text tool.
I have a lot of lines that I need a length, like in attached file. At this moment I do it with a vba that put fields in all lines.
The problems:
1) fields makes drawing slow to regen or after I modify line.
2) fields not follow lines slopes and position, if I stretch or move one end point of line. Text must be in middle of line.
So I thinking use reactors .
I tried reactor but I don't have much experience in lisp and I am having problems with persistent reactors, after I close file and open again, load lisp. Reactor not continue persistent.
This is a test that I tried. Works only for one line.
(defun print-align-text ( owner reactor lst / sp ep a d )
(setq sp (vlax-curve-getstartpoint line1))
(setq ep (vlax-curve-getendpoint line1))
[Code].....
I have read that is better store data using XData. In VBA I tried construct class module with events, without any success.
I have a large group of lines that I want to get a total length of. Right now the only way that I know how to do this is to highlight them all and use the list command but then I have to go through the text box and write down each line length and then add them up. This is fine if I have only a few lines but when you get into the hundreds or thousands it becomes a monster task.
I tried copying the text box data into a Word document, removing all of the text except for the line lengths and then dumping that into Excel to calculate. This works ok for a hand full of lines but is not really practical.
I know that there are LSP routines that can do this in the full version of AutoCad but LSP is not supported in AutoCad LT.
Is there a way to automate this process in LT?
Or maybe extracting just the length data from a line to a text file where I can send it to Excel and use Excel to add up the lengths?
Is there any way to import DWG/DXF files with measure lines with arrows.
system configuration:
Win 7 Pro 64bit, Intel i5-2500, 8 GB RAM, 128 SSD SAMSUNG + 2TB on hard drives.
corel version:
X6 VERSION: 16.4.0.1280
How can I have sketch lines drawn to perfect lengths. I mean it should be in multiples of 1/16 of an inch.
Inventor Professional 2013
Vault Collaboration 2013
I opened a part today and noticed that it had collapsed into itself.
This should be a rectangle 85x15.75:
On closer inspection it appears that the vertical lines somehow became zero length lines. Why does this happen?
Edit: I should mention that I was able to repair the skecth by making the 85" dimension driven, then dragging the line over...
Is there any easy way to get the total length of selected lines (even if they are not "connected") ?
View 6 Replies View RelatedI have a plan prepared for CNC steel sheet laser cutting. One factor in the costing of the cutting is determined by cutting time or length of cutting. I want to determine the total length of all the lines in a selection so that I can determine what is the most economical design to achieve my goal. Is this possible in ACAD?
View 2 Replies View RelatedI have a line that i would ideally like to divide into 3 equal segments. The divide command places points along the line, but I can't snap to them.
I know that I can place a block at each point which I could snap to, but is there a way of doing it without creating a block? Also is there a command that actually splits a line into 3 equal-length lines?
Some times when I re open a drawing I have been working on, I start to dimension and I notice that the dimension extension lines stay the same length when I move the dimension in and out from the object being dimensioned.
Not sure why this happens, I do all my dimensions in model space, in fact I do just about everything in model and then just set it up in paper space to print.
I never change anything when I start a new drawing in my template, so not sure why it happens.
I am drawing a diagram to describe a mathematical word problem. Since it is easier to visualize with a drawing, I want to draw it using the given dimensions. But angles used in the diagram are unknown and are not needed for the answer to be calculated, so the only way to draw this freehand is to guess at the angle resulting in the correct distances to be off.
Here is the word problem: There are two ladders, one 40 feet and the other 30 feet, each touching the base of one of two buildings and leaning against the other building. If the ladders cross 10 feet above the ground, how far apart are the buildings?
So for my drawing, being rather simple considering what AutoCAD can do, results in this:
Can AutoCAD calculate the angle needed to place a line of a given length between two parallel lines that are a distance apart less than the length of the line to place between them, having the endpoints of this line touching the parallel lines, fitting exactly?
For the word problem, the distance between the two parallel lines is what needs to be solved and the math is quite invloved, having to find the roots or solution of a quartic equation. (I have the solution figured out to be 26.03287754 feet)
What I am afraid of is that this would require to program an AutoLISP routine to create a new command that one can call from the command line. I see it using the the measure command with relative and absolute co-ordinates. This may be far from a "beginner" question. I can do this quite easily on a peice of paper: having two parallel lines drawn, take a ruler and placing the "0" mark on one line, then adjusting the angle until the desired length just reaches the opposite parallel line. I used to use this trick quite often when drafting with pencil and paper to divide a distance into a required number of even amounts, so this can't be that difficult to do with AutoCAD!
Is there any utilities that can select the entire drawing with the 2d polyline and erase all the polyline less than specify length (eg:10m,20m etc) ?
View 4 Replies View RelatedI have lisp code, which count total length, but I need that it count and multiply by constant which I choose manual (such as in example, total lines yellow length * y + total blue lines * x = ... , example 50*2 + 60 * 3=280),
remember the another code, such as I have d200 with total l=1000 and d250 with total l=1500, i need to count total cost such as 1000*y+1500*x
one think, diameters numbers is not only 1 or 2, it can be many different diameters.
dwg file here:
[URL]..........
lisp file here:
[URL]........
I just recieved a structural drawing from an engineer that has the entire drawing drawn on layer 0. This poses many problems for me as I need to differentiate text from lines and lines from lines. The darwing does have two colors although entities are still on same layer. Is there any way I can seperate the yellow lines from the red lines even though they are on the same layer?
View 6 Replies View RelatedI have an OS plan with the 100 metres squares marked.I want the ruler to coincide with the known 100m length.Then I can mark on layers various lines of say 7m or 25m long.How can I set the ruler and guides to enable me to draw lines such as this.
View 9 Replies View Relatedis it possible to extend the dropdown box so i can view whole layer names?
layer toolbar.jpg
