AutoCAD Inventor :: Distribute Space Between 2 Rectangular Assemblies?
May 15, 2013Now how do I smartest align two assemblys to same center point or distribute even space on 2 sides of the attached par example?
View 8 Replies
ADVERTISEMENT
AutoCAD Inventor :: Promoting Parts In Assemblies From Stock Sub-assemblies Or Component Groups
Oct 3, 2011I am working in an Inventor Assembly .iam, I have about 250 fasteners (screws) that are constrained to a flat washer and lock washer. I would like to put them in as a single unit (sub assembly if you will) and then promote or explode them in the top level so that my bom has 250 screws, 250 washers, and 250 lock washers all at the same level, not associated to one another except thru the constraints that were entered in the original assembly. I have tried Promote but that doesn't work because it removes the washers from the original file and I end up with only 1 instance of the assembly. Am I approaching this incorrectly? Is there a better way? I run across this scenario with different components quite often.
View 2 Replies View RelatedGIMP :: Distribute Tool Not Making Same Space Between Objects?
Jun 18, 2012I'm trying to get the distribute tool to distribute some text objects (for a website menu) evenly. however, using the distribute section of the alignment tool only enables me to set an offset that measure the distance between the left, center or right edge of each object. if the objects are different widths, they will have varying distances between their edges.
View 2 Replies View RelatedAutoCAD Inventor :: Busting Up Sub Assemblies In Upper Level Assemblies?
Mar 8, 2012If you have created a sub assembly and inserted it into an upper level assemby, is there a way to bust up the sub assembly at that level?
The issue arising is the individual components need to be called out on the upper level, but in the drawing are all showing up as the same balloon.
Illustrator :: Distribute Spaces Option Doesn't Space Evenly In CS6
May 24, 2012I'm working in Adobe Illustrator CS6 and neither the Distribute Spaces Option nor Distribute Object Option are working.It doesn't seem to matter if it's a print or web document. Doing the same thing to the same document/graphics in CS5.1 works perfectly.
Copypasteing the correctly distributed objects from CS5.1 to CS6 works ok, and if i then repeat the Distribute spaces option nothing changes and it stays correctly distributed. (read: it doesn't badly distribute like before)
AutoCAD Inventor :: BOM For Assemblies Within Assemblies
Jul 12, 2012i have a valve vault assembly that i am creating that has two headers running through a large cylinder vault. how i get a total BOM if i were to create the header assembly file separate from the the total vault assembly file. is there a way to explode the header assembly bom when i do the drawing.
View 1 Replies View RelatedAutoCAD Civil 3D :: Assemblies Not Registered / How To Get Assemblies To Work
Jul 20, 2012I'm trying to use assemblies when creating a corridor. The Tool Pallette is emply but I can drag the assembiles in from the Catalog. I've also created an assembly using the ASC. Neither work when I try to use them. The error message is attached.
I'm using a network installation and I do not have the option of changing it to a DVD installation.
AutoCAD Inventor :: Making A Rectangular Spring?
May 2, 2012I have to make a spring for an engineering class I have yet me nor the teacher know how to make a rectangular spring.
View 3 Replies View RelatedAutoCAD Inventor :: Twist Rectangular Tube
Dec 24, 2013Im trying to reproduce the part attached. Its a rectangular aluminum tube. .320 x .180 approx an inch long. I tried lofting 2 sketches but the result does appear like the attached image.
View 8 Replies View RelatedAutoCAD Inventor :: Equation For Rectangular Pattern
Feb 22, 2012Can an equation be used to calculate equal distances when using the rectangular pattern.Regarding the attached .ipt file i would like to place 25 holes in the X direction with equal gap size between each hole.Also how to calculate the number of holes in the Y direction again with equal distance between each hole.I have not done this before with equations but was thinking that i would need to use the Length x Width in the equation.Do i need to add figures into the Parameters box also?
The attached file with the Hole feature the sketch is not constrained for the purpose of using an equation so i know how far from the start of the part to get equal distances between each hole to the end of the part .
AutoCAD Inventor :: Dimensions Of Rectangular Prism
Jan 1, 2014regarding obtaining the dimensions of a simple retangular prism?
In this particular case (file attached) the geometry was imported from Revit, so it's really just imported SAT file. After importing, "Make components" was run to generate individual part files. The resulting part is therefore created using the origin of the parent assembly, so although it's "just a box" - it is spatially displaced and oriented at an unknown angle.
I'm looking for a way to identify the 3 dimensions that define the shape of the prism.
AutoCAD Inventor :: How To Adjust Rectangular Pattern
Feb 20, 2012I am using Inventor 2012. I have a horizontal feature that terminates at a vertical plane on one end and an angled plane at the other end. I want to pattern it down but when I use Adjust, the patterned features do not adjust to the angled plane. They just go strait down from the first feature.
Does Adjust only work if the terminator is a solid surface instead of a plane?
AutoCAD Inventor :: IPart And Rectangular Pattern
Nov 3, 2011I am having a problem with an iPart. I created a rectangular patern in an iPart. When I place the member of the iPart in the Assembly file the pattern is not there. I need it to constrain another part to it.
View 4 Replies View RelatedAutoCAD Inventor :: Non-Circular / Non-rectangular Pattern
May 14, 2013I am currently trying to model a multi cavity mould tool. The cavities themselves do not follow either a circular or rectangular pattern.I have modelled one of the cavities using a revolve internal to the tool. I have also sketched out on the upper surface centre points where I need the cavities to be.
I was hoping I would be able to copy the cavity feature, select a base point and then use the centres from my second sketch to place the cavities.
I don't seem to be able to find this option. The copy and paste feature will likely work but it is hugely long winded positioning each cavity individually. Any method I might be able to use to model such a part?
AutoCAD Inventor :: Rectangular Hole Pattern
Dec 1, 2009Looking for some sample code for patterning a hole in a part using Inventor 2010. I dont need it to be selected because it is the only hole i have in the part. My main trouble is that I am having trouble withobjectcollection idea. As you can guess I am a newbie at Inventors API.
View 5 Replies View RelatedAutoCAD Inventor :: Positioning 2 Sub-assemblies Exactly?
Mar 25, 2013I have 2 tanks, each one is an assembly in itself, and they have to be positioned on a steel skid, also an assembly and then interconnecting pipework between the two. My prioblem is that I can't seem to find a way to position the two tanks at a set distance from each other and in relation to the edges of the skid.
Because of this, my pipe router is going all over the place in trying to join up the two termination points.
AutoCAD Inventor :: FEA On Bolted Assemblies?
Sep 22, 2009Will the next release of Inventor have the capability to perform FEA on bolted assemblies?
View 9 Replies View RelatedAutoCAD Inventor :: Allow Motion In Sub-assemblies?
Dec 20, 2011In SW I was able to create assemblies that had components with limited motion and then set them as "Fllexable" and allow them to move in larger assemblies. How do I do this in Inventor? I have a trailer with both the front and rear axles able to pivot. These axle sub-assemblies are both able to pivot as top level assemblies but when they are assembled in the trailer assembly the only way I have found to allow movement is to make one axle active and move it then activate the other nad move it. This doesn't work well if there are several interdependant subassemblies that should move together. I am in Inventor 2012.
Inventor Premium 2013 SP1.1
Vault 2013- plain vanilla version
HP G71 notebook
celeron cpu w 4gb RAM and 64 bit system
Win 7 home premium
AutoCAD Inventor :: Re-Using Assemblies As Components
Oct 21, 2011I use hinges in my door assemblies and they are basically placed into the assembly each time and become flexible so the doors can operate. The hinges are one size and don't change in any way or shape. What is the best practice for inserting these hinges into my door assemblies?
Inventor 2013
Windows 7 Professional 64-bit SP1
HP EliteBook 8470w
Processor: Intel(R) Core(TM) i7-3610QM CPU @ 2.30GHz
Memory: 16 GB
AMD FirePro M2000
3D Connexion SpacePilot
AutoCAD Inventor :: Use Assemblies In Library
Aug 3, 2012I have converted a lot of STEP files to .iam files. What is the easiest way to put them in a library? there is realy no need to publish them is them, i already have them in subfolders etc.
View 6 Replies View RelatedAutoCAD Inventor :: Reference In Assemblies
Sep 27, 2011We have some structure issues going on. Below is an example of our current structure.
1. Overall Frame Assy
2. Frame Weldment
3. Spine Weldment
3. Bracket Assy
4. Deck Brackets
4. Air Brackets
4. Hyd Brackets
The biggest problem is we have all of these level 3 and 4 subassemblies that need to reference upper level assemblies to show placement on the drawings. We have tried utilizing LOD's and view reps but still can't fix the problem. The problem comes into play when we get to upper level assemblies that become so huge because of all of the references that are happening at lower levels. It is structured this way to create small BOM's and to be able to use in multiple different structures without having to pull a new Part Number.
We need the reference geometry to be able to show on the drawing our locations of all of these lower level assemblies and how they mount to the frame in their respected locations.
AutoCAD Inventor :: Sub-assemblies Disabled In BOM?
Apr 24, 2012I'm trying to change the BOM structure of some sub-assemblies from "Normal" to "Phantom". However, some are displayed as disabled and therefore do not allow any changes/overrides. How can I enable these in the BOM?
Inventor RS 2011
AutoCAD Mechanical 2011
ASD 2013
Vault Collaboration 2011
Windows 7 Pro
AutoCAD Inventor :: 2D IParts In Assemblies?
Aug 14, 2013This is using Inventor 2013 Professional.
I've created a simple iPart and want to insert multiple instances of it into an assembly. The plan is to use a parameter-driven iPart to create multiple variations on the same basic model which will eventually be lasercut.
I've included a sample archive. 2DiPart is a simple part with a couple parameters. 2Dassembly is where I've tried to include this part. I'm able to walk through all the dialogs to place the iPart, and will even see it in the canvas as I select the insertion point. However, after I dismiss the dialog, nothing shows up in the canvas. I'm still able to see the component instances in the project explorer however.
How to best to get multiple instances of a parametric iPart into a drawing that can be lasercut.
AutoCAD Inventor :: Circular / Rectangular Pattern Sketch Name
Nov 19, 2012I need to know what sketch is associated to either a "Rectangular"or "Circular"array. This is so I can filter out sketches that are not repeated in an array.
Here is my code so far (Circular Array).
Dim oCP As CircularPatternFeature
For Each oCP In oDef.Features.CircularPatternFeatures
THIS IS THE TROUBLE LINE If sketch = oCP.Parent Then
Set oCP = oDef.Features.CircularPatternFeatures.Item(oCP.Name)
[code]........
I have a simple test part containing an extruded disk (Sketch1) and 8 holes on a pcd (Sketch2). I only want to array a sketch if it is arrayed.
AutoCAD Inventor :: Rectangular Pattern Cannot Be Applied On Bolt
Jan 9, 2012I can not use rectangular pattern for bolt in an assembly.
View 7 Replies View RelatedAutoCAD Inventor :: How To Create Rectangular Pattern Of Welds
Mar 21, 2013I'd like to make a rectangluar pattern of a part that is groove welded into a plate. Inside the pattern command I can select the part but not the weld. How to avoid having to do each weld individually?
View 2 Replies View RelatedAutoCAD Inventor :: How To Suppress Items In A Rectangular Pattern
Aug 29, 2013If I have a RectangularPattern how do I suppress individual features in the pattern.
For example I have a single row of holes, and I want to suppress the odd numbered holes.
I've tried this...
CComPtr<FeaturePatternElements> pFeaturePatternElements ;
pRectPatFeat->get_PatternElements (&pFeaturePatternElements) ;
const int ikNumElements = pFeaturePatternElements->GetCount() ;
wprintf (L" this has %d FeaturePatternElements
[Code]....
... but it crashes at the assignment of Suppressed
AutoCAD Inventor :: Circular / Rectangular Pattern Feature
Jul 23, 2012While using the Circular Pattern feature or rectangular pattern feature in Inventor, sometimes I want to extrude (join) or cut the drawings that I made (augmented) with using circular pattern feature, rectangular pattern feature. in this case do I have to choose all the augmented members one by one (for instance I make 42 augmented members), it can take a lot of time. also after applied any of these features I can't use trim feature, can I ? but sometimes using the trim feature after applying the Circular Pattern feature or rectangular pattern can be necessary.
View 1 Replies View RelatedAutoCAD Inventor :: Curved Rectangular Spring / Animate
Sep 23, 2012A multi-part question:
1.) How do you recommend I model a rectangular spring?
2.) How do I apply the concept from the initial question and apply a curve to the spring?
3.) How do I mimic the properties of a spring in animation?
AutoCAD Inventor :: Shrink Wrapping Assemblies
Jul 6, 2012What is the best setting for shrink wrapping an assembly?
I've found shrink wrapping it as a surface causes problems with the video card when rotating the model and placing views on a drawing.
AutoCAD Inventor :: Highlighting Parts In Sub-Assemblies
Oct 16, 2012I'm having a problem highlighting parts within a sub assembly. A simple structure to demonstarte this issue would be:
TopLevel.iam
|
SubAssy.iam
|
ChildPart1.ipt
ChildPart2.ipt
Using this structure I wish to highligh ChildPart1.ipt, howver my vba macro code below doesn't seem to work (nothing happens):
Public Sub Highlight()
Dim SubAssy As Inventor.AssemblyDocument
Dim ChildPart1 As Inventor.ComponentOccurrence
[Code].....