is there a command or workflow to split all intersecting surfaces? currently we build surface models and split manually or open in autocad, explode, overkill, breakall, then export the lines for rebuilding in an FE package.
Ideally we would like to export straight from inventor with one hit i would like to do the 5 splits below the EOP marker automatically
is there a command or workflow to split all intersecting surfaces? currently we build surface models and split manually or open in autocad, explode, overkill, breakall, then export the lines for rebuilding in an FE package.
we would like to export straight from inventor with one hit
I am working on Sweeping three helix profiles around a cylinder to create a screw thread. When I sweep the profile, Inventor gives me the error messages:
"The attempted operation would create a self-intersecting surfaces. Try with different inputs".
or
"The attempted operation did not produce meaningful intersection edges from the face-face intersection. Try with different inputs".
However, this is exactly what I need to create the helix profile I require and eventually increase the size of the Extrusion Sweep profile to 80mm. When I increase the sweep profile to 80mm I get the same error message about the self intersecting surfaces.
I am working with Autodesk Inventor Professional 2011, 64bit, 8gb RAM, Windows 7, Intel Core i7-2860QM.
Using Conceptual View, I have hanger plates that intersect an arch, and previously where they intersect you couldn't see inside the arch just the surface. Since saving as another drawing to add hangers details something has changed in the display and the arch appears transparent at the moment so you cant see where along the plates the arch intersects.
Unless you zoom right into the intersection, the surfaces appear and zoom out and it goes transparent again.
I am trying to modify a hoop instead of having a half circle, i half to cut the hoop short and add a flange, instead of starting over, is there a command I can use that I can create a flange and join the hoop and flange at the intersect..... the hoop was made using the fold feature...
View 9 Replies View RelatedI have a rectangular chute, tapering in width and height, and intersecting, at an angle, with a round duct. I can't seem to find a way to determine the cut-out in the round duct.
Because the chute tapers projecting the size onto a flat plane to then project onto the round duct doesn't work.
I'm trying to find the intersecting points of a part that connects to the outside surface of a cylinder shaped part.
What is the best way to go about this? I have attached some images that hopefully illustrate my problem.
I want to create a solid using VB and loft definition.
I creat each time different planes that have a constant distance in x dimension and a steady rotation each time φ (deg).
On each each plane i sketch the same profile and that is happened for 360 deg.
The problem is that Loft is not made because a line of the profile must follow a line tragectory and all other points must follow a circular tragectory. Also, there is a problem from 180 deg to 360 because there is intersection of profiles.
The result must be a solid similar to snail shell but all the same solid, as a cylindar whith a half sphere in the bottom.
I need to trim a part that intersects with many other parts in several different sub-assemblies - on an angle.
**Attached is an image of my problem.
Split tool is disabled. It is only usable once I drill down into the assembly/part - it will not select the other cutting objects higher up the browser stack.They become ghosted.
What I need is a tool that projects intersection lines. Does Inventor have something like this? Standard projection lines on the part is not working because the cutting objects are not 90 degrees angled to the part to be cut.
This may be easy,.. I am just not seeing a way to do this with out a bunch of work-a-rounds.
In regards to sweeping, what does the title of the post mean (self intersecting paths or loops are invalid for this operation). I have a 3D sketch consisting of 1 straight line, one spline with 4 points dictated by 'points' and an arc. All have tangential constrains to each other and I am looking to sweep a circle along this path to create a bent wire. I don't have anypictures or files as it is a stand alone computer at the moment.
View 2 Replies View RelatedAttached shows lines (Parts) are intersecting each other in drafting mode. I have tried all but I am not able to resolve this issue.
View 1 Replies View RelatedWe build ASME chambers that have ports and tubes that intersect at various angles. When these tubes intersect at a standard angle, center on I have no problem creating the sheet metal layouts for the tubes. The attached PDF shows one intersecting at two differnet angles, off axis.
he sheet metal layout fo the tube part? I have modeled it pretty well, I just can't figure unfolding the tube portion. The head is a buy out item, we have that.
I have to ascertain two things ultimately, the hole size/layout (easy) and the tube (stumped).
I have a very large assembly drawing. The BOM is three times the height of my D size format. How do you split the BOM to break it into 2 or 3 columns instead of one large one that does not fit on the paper?
View 6 Replies View RelatedHow to get surfaces in a dwg to display correctly in inventor 2012? (just upgraded after SP1) I keep getting random results. I have a seat from our supplier translated from solid works brought in as a composite (converted in inventor 2011). I have assigned colors to faces and in the part/assembly environment it is fine, as soon as it is in a DWG it goes randomly transparent! Some times it is completely see through and others you get an odd face displaying correctly! Even in different views on the same sheet different faces appear normal.
Attached jpegs are: surfaces in dwg and surfaces in an assembly.
Inventor 2014 Professional
Dell Precision T3500 Intel Xeon
Windows 7
Quadro 4000
Inside Leg 35 inch
After you create a drawing view, surfaces can be included or excluded from drawing views. Files that contain only surfaces automatically include the surfaces in a drawing view. Is there a way to disable this functionality?
View 2 Replies View RelatedWorking on a part and after much extruding and intersecting ended up with pretty much what I was after, but there are all these surfaces that don't seem to clean up by boolean operation of the solids. Will this cause a problem when I go to manufacture from STL file ?
View 5 Replies View RelatedI am attempting to revolve a sketch between two surfaces in Autodesk Inventor Professional 2012. The problem is that the extrusion is being created on the opposite side of the two surfaces that I want.
For example, I have two flanges on a cylinder. I would like the feature to be created to stretch on the lower side, the larger angle, where the sketch is. Instead, it is creating the feature on the upper side, the smaller angle.
I have adjusted everything I can within the revolve feature options, including unchecking "minimum solution" and switching the starting and terminating faces.
In the attached file I am attempting to revolve "Sketch 7" about the x-axis, between the two flanges closest to the "top." The sketch is centered on where I want the revolved feature to be created.
I have a part I have drawn in inventor. It is saved as an ".ipt" file.
I would like to split this part into two seperate Ipt files so i can assemble it a different way.
For example,
the part i wish to design is an alternate keying of the one i just drew-
meaning that a solid of the part is rotated 60 degrees in this case.
Is it possible to do this with inventor commands?
I modified a box build in Inventor in Fusion and then imported it back into Inventor as a bowl. I am trying to split the bowl in half and create an assembly drawing which I can submit. When I try to split the bowl I get and error message: "The attempted operation did not successfully complete due to unforseen problems. Try with different inputs or outputs." I've attached the file in case you want to try yourself.
View 2 Replies View RelatedI want to apply a pressure load on portion of a surface in my INVENTOR solid model. My problem is that i cannot split the surface in inventor easily. I did it my creating a separate surface with an offset that i reduced to almost zero.
View 4 Replies View RelatedI made all my polygons with the same technique but somehow interactive polygon split tool does not split all polygons... I attached a file with which I have problem. Split tool just "disappears" after submitting changes...
View 1 Replies View RelatedI am using 2013 and my construction surfaces keep displaying in my drawing views. They are hidden at part and assembly level and include surfaces is greyed out but they show as visible in the feature tree in the idw, and in the views.
Is there a setting somewhere to stop this. This is from IDW. They should not be visible.
I have successfully opened a STEP file from our Engineering group and saved it away as an Inventor Assembly. I would like to define Materials and/or Surface finishes for all parts. Why wouldn't the Surfaces and Materials synchronize between the Styudio's Surface Creator and the BOM Materials Control in the Assembly area?
I have found the way to define a new Surface in the "Inventor Studio" Interface and saved it with a unique name. Now, I would like to assign that Surface as a Material to the parts in the assembly ... and of course I would like to define numerous other surfaces and materials for assignment to all the parts throughout the assembly. Finally, I would like these surfaces / materials to follow the model into Showcase for presentation purposes.
I have placed the views but whenever I want to include all surfaces from the history tree they appear for 1 second and then they disappear.
View 5 Replies View RelatedIs it possible to show surfaces in a drawing view of an ipart member - although the option of include all surfaces is there I can't get them to show. Similar issue with showing sketches - get model sketches is there but nothing can be shown.
View 2 Replies View RelatedI've been doing a layout drawing of a plant
The floor of the plant is split into different faces to denote walkways etc.
When i saw they were missing from the drawing i thought it could be because i haven't 'included surfaces'.
I clicked on include surfaces on the model and it worked!
However, when the green arrow update finishes, they disappear, and the include all surfaces box is unticked! i didn't untick it, so what did?
Inv 2013 64bit
I want to make symmetric surface i.e. golf ball with dimples. I found that I can do them by using revolve cut but how can I set them symmetrically on whole spherical surface.
View 5 Replies View RelatedI'm trying to make a solid part from the attached file. I tried sculpting the part but only the sides of the bracket become solids.
View 3 Replies View RelatedI have two .dwg files that represent two different surfaces. I would like to import each .dwg file into Inventor, then create a solid with the original surfaces serving as the top and bottom. I can send the .dwg files if necessary.
View 9 Replies View RelatedURL....However when I try to export to .STL it won't do it because it is only surfaces and not a solid.I have searched everywhere on how to convert from surfaces to a solid but nothing I have tried has worked.
View 8 Replies View RelatedI have a BIG assembly with parts and surfaces. Of this I only need a relatively small cutout through the XY plane.
I tried extrude cut but that won't include the surfaces, and it will still calculate everything before the cut, right?
Inventor standard 2012, 12GB of RAM,.