I have started to make a custom librabry in the Conter Center with our company products. At the begining I didn't think too much what categories I will need, but now I need to reorganize some categories and to move some families parts into other categories. But I can't find how to do that. I see that it's possible to move the them to other librabry.
So for the moment I just want to move 2 families for J-TEC catergory in the upper category named Piping and then just to delete the category J-TEC.
AIP 2014
Windows 7 x64
Dell Precision T7400 Intel(R) Xeon(R) CPU X5472 @ 3.00GHz (4 CPU's), 8Gb RAM, NVIDIA Quadro FX 5600 1536MB GDDR3
We have a custom content center. The families were brought in using "Copy to".Lately, sometimes, when editing a family in the custom content center the family suddenly "disappears" while I am still working on it. I can't see it. Other users on other computers can't see it, but content center editor believes it is still there.
In this particular case the "missing" family was called Hex Bolt -Inch.If I try to use "Copy to" to bring it back and start over I get a message like "Category Head Head in library GLM contains a family with an identical internal name. Would you like to replace the existing family ?(see attached file)" The filters do not seem to be the issue, since I can use "Save Copy as" to place the family (as long as I don't try to use Hex Bolt -Inch as the name) and I can see it.(see attached file).
Attempting to place the bolt after the disappearance causes runtime error and system crash.I always have to get our IT department to restore the file from backup, and I lose all the work i have done.
I am using Build: 219, Release: 2012 SP2 on a 64 bit Windows 7 operating system
We use different types of Stainless Steel fasteners. For example 18-8, 304, 316, etc. When I use the "Material Guide" in the Content Center Editor it only has the Autodesk default materials listed. How do I add CUSTOM materials to this list to create new families with my custom materials?
I want to select part of an image with just one layer. Say I just flattened the image and have to move one part of. I select it with the rectangular select tool. It seems intuitive that I could then just move what I selected, but when I drag the selection, the selection itself moves without moving what is inside the selection.
If I then remember to click the move tool and try to move what's in the selection (seems to work sometimes, maybe when there's multiple layers?) the entire image moves.
The only way I can move part of the image over is if I make a selection and then cut it (ctrl X) then paste it.
How am I supposed to move part of the flattened image, is there a way I can set it to default to "When I select something, I can immediately drag that selected area around."
I created a keyplan as a generic annotation family, with masked regions representing the various segments of the building. For some reason, my palette of hatches within this family template is very limited, and I cannot choose a dotted pattern for the masked regions, which is an informal company standard.
From what I've seen, adding new hatches is a cumbersome process. Since a simple dot pattern is available in project files though, is there a simple way to add that hatch to this family file?
in inv 2012, if I create a new part with adaptivity within an assembly the datum of the sketch ends up wherever, if I break links and remove the adaptivity, is it possible to move the absolute datum of the sketch to a decent position within the sketch?
I have probably a very simple problem but cannot figure out how to do it. I am adding text to a drawing and I want several leaders to be associated with this single text. I add my first text at tow head and then do a add vertex/leader. It will not let me add one unless it is on a line.
And it adds it but then I cannot get it off the line. I have tried holding down the shift, control and alt key before, during and after I have highlighted the arrowhead to move.
I've been making a model plane model in inventor 2012 from imported IGES geometry, and Realised that my sketches were not assigned to any part (and thus can't be lofted). Is there any way of moving the sketches to the newly created part without redrawing everything? I've tried dragging and dropping because it seemed to make sense, but alas, that had no success.
When I place parts in my assembly they are stuck in the position I place it and can only be moved once I mate it to another part of my assembly. I have only recently encountered this problem, as usually when I place a parts in an assembly I am able to simply click on the component and drag/move that part around to put it in a place that suits before I use any constraints.
What is the problem, have I clicked on some function unknown to myself which has disabled the ability to move parts/assemblies when I place them into an assembly?
I have some "insert" constraints for DIN rails in holes. I've moved the holes, but the DIN rail doesn't move. The refresh button isn't "lighting up", or when it does, it does not do anything to move the rail. Is there something that's been "shut off" to keep things from moving?
I like the new(ish) feature where you can drag a section plane through a component, but is it possible to program a moving section and record it to an avi file? Is this something I can do in 3ds, Studio or Showcase? IV2013
I created a sketch on a 'fixed workplane' and extruded it. I would like to know if it is possible to move the workplane? I understand I can change the workplane if it is a 'plane by offset from plane'.
If moving a fixed workplane is possible, does the extruded features move along together?
I have a problem regarding a mechanical design. I want to make a pin move around a complex shape, always tangent to the sides of the shape. The point is not to have it animated, but I need the constrain so I can further work on the mechanical design.
So I have this assembly with all parts constrained properly yet it won't let the parts move the way they should under the constraints applied and it's telling me I have interfering constraints.
I checked the "broken" constraints over but they look fine. It's a relatively small assembly (10-15 parts), although the parts have been used in a previous assembly. Would this affect their behavior?
I have numerous step files which I have imported into an assembly. I now need to move all the imported files to a predefined UCS (not 0,0,0). I can do this manually by using the assemble command and selecting the centre point then selecting the centre point of the pre-defined UCS.
I have potentially thousands of parts to move in various assemblies, is there a way to do this using iLogic and if so, how?
I need to find out how much smaller the part in the upper image is so it fits inside the similar shape in the bottom image. The real part is a bit more complicated so it's hard to calculate if it fits. Is it possible to make those parts in assembly mode so that they don't move through each other and I could move the upper part inside the lower and find out that way if it fits?
I'm new to Inventor and I've been working on a complicated part for quite some time. However, I've just realised that I've made an error at the very beginning. I'm drawing the part in the YZ plane and extruding along the X axis. My problem is due to the fact that I began the drawing at x=0 when I should have began at x=7780mm. moving the entire part in the positive X direction? I've tried several approaches but none seem to work.
I am trying to take a countertop that I have in this bathroom remodel floor plan and place it onto a separate sheet so that I can send it out for pricing. I created a new sheet "countertop details" However, it is not letting me add it - I keep getting this warning "Can't create this kind of element in this view in the current mode." I know the answer is in one of the parameters but I am still trying to get used to this program and teaching myself.
I have a pile family where i have created a Shared Text parameter under Identity data called Vert Load. I have nested this into a pile cap family in several locations and have the same Shared Text parameter. If i select the pile in the pile cap family i have the option to put a value in the properties dialogue box under Vert Load. The pile cap family is now loaded into my project and the parameters shared in the project. When i select the Pile cap in my project then i have the option to add a value for the Vert Load but in this pile cap i have 3 piles and i want to give different values for each. When i select an individual pile within the Pile cap family then the Vert Load value is greyed out.
I want these vert Loads to appear in a schedule... I've attached a couple of images.
I am doing a window nested family with two windows that have three voids to perform the wrapping of the stucco layer and the gypsum layer independently, but in the nested family I get a wall sleeve between both windows. I have used voids with parameters in the nested family, but when inserted in the projects the voids don't cut anything. See the images.
If i delete a family from the project browser, under families expanded folder group, will this delete them from the project and reduce the file size?
Best way to delete just unwanted families that have been loaded into the model?
I know of purging the model but i believe this will potentially delete tags i may want and other information that just not being utilized at the time of purge.
When I browse through the fonts in my control panel or character panel, they are not sorted alphabetically. Some of them are, but as far as I can see, they are first sorted by language, then alphabetically. Can this be turned off? I think this is common to all versions of Illustrator.
I have a script that is perfectly works in 2012 inventor pro version. It moves newly added virtual parts into the VIRTUAL_PARTS folder. Part of script is below:
Dim oFolder As BrowserFolder Dim oTopNode As BrowserNode oTopNode = oPane.TopNode() Dim oTopNodeOcc As BrowserFoldersEnumerator oTopNodeOcc = oTopNode.BrowserFolders For Each oFolder In oTopNode.BrowserFolders i = i + 1 Next If i = 0 Then oFolder = oPane.AddBrowserFolder("VIRTUAL_PARTS", oOccurrenceNodes) Else For Each oFolder In oTopNode.BrowserFolders If oFolder.Name = "VIRTUAL_PARTS" Then For Each oOcc In oAsmCompDef.Occurrences If TypeOf oOcc.Definition Is VirtualComponentDefinition Then oNode = oPane.GetBrowserNodeFromObject(oOcc) End If 'MsgBox(oTopNodeOcc(1).Name) oTopNodeOcc(1).Add(oNode) Next Else ' do nothing End If Next End If
In 2014 pro it works only once, when I add first virtual part. It creates a folder and moves it there. When I add 2nd virtual part it gives me a error
I've used the transitional constraints with good results but unfortunatley the cams are moving all over the place when I try to move them by dragging with the mouse and not very stable.
I'm trying to animate a couple of bodies along a path with a workpoint that will move the assembly at the beginning created using a rectangular array along the path. I have a UJ in the middle of the bodies attaching them together. As I change the distance of the rectangular array it will move the first body as expected. How I constrain the other body to follow along the path with the ride points as labeled?
I've trieds almost everything I think. Should I use dynamics to simulate this? I don't have the dynamic installed however is there a way I can get ahold of a test version so I can test this?
I am trying to move a component within a part drawing, not an assembly. When I do "move bodies" it wants to move every extrusion within my drawing. If I click move face, then I have to click every face that I want to move (which is time consuming) and then it often times doesn't work? Sometime it works other times it just moves the origin indicator and doesn't move the faces I have selected.
I can't move the assembly I'm building around without the parts moving out of place from where there constrained too. I manly use mate and flush constrains. I have to build a layout of a room later on with these assemblies in it and they must be able to be positioned where they need to be. How do you keep your constrain parts from moving out of place?
I am using Inventor 2010 and would like each view of a drawing to show a different machining step. I.e.. A rough cut dimension and then the finish cut dimension. Is it possible to create the part as it would be machined and then use the EOP marker to set each view. Would like to model one part and get all views.
I have a bunch of parts that are almost identical except for a few minor changes each time. Most have already been created in Inventor. My problem is that I want to rotate the part so that a face that was once along the XZ plane will now be in the XY plane. Is there anyway to rotate it like this? I would like to do this so that when I bring it into Mastercam, I don't have to rotate it each time.
I have a sub assembly with a sliding part in the main assembly but the sliding part is locked, the "flexible" option is greyed out?My head is not in gear this year yet! Am I able to move unconstrained parts in sub assemblies via the main assembly by pulling them with a mouse?
