Is there a way in Inventor (or any other Autodesk Design Suite program) to find the point on a cone (attached jpg) where the lifting lug should go so that when lifted, the cone stays in the same orientation as in the attached picture.
View 4 Replieshow to get a flat pattern from a cone with knuckle. I am using 2013.
View 5 Replies View RelatedI have a cone shaped part and would like to put a hole in the curved face. I would like have to hole square to the face in the flat pattern so it can be cut on the plasma table, is there a way to do this? I attached the part with holes in the approximate location.
Windows 7 Pro 64
i7-980X
12Gb ram
GTX460
Is it possible to make a cone with sheet metal that can be unfolded?
View 9 Replies View RelatedWe commonly weld two half cone sections together to make a complete cone. To show the weld prep i have modeled a chamfer on the cone edges.
When i try and show the chamfer on the drawing using a section I cannot dimension the angle as the surface is viewed as a curve by Inventor.
I have attached a drawing and part file showing the problem and showing the detail I would like (I've shown the detail using a simple sketch).
How do I make this flat pattern correct... it might be that I have to use a different way to folded up the crimp But I'm new to crimps
View 4 Replies View RelatedWe're seeing strange behavior on all of our workstations when using a Refold feature on a sheet metal cone. Surfaces are (very incorrectly) being added at the top and bottom openings of the cone when the Refold feature is added. The behaviour is the same whether using Contour Roll or Revolve. The surfaces dissappear when the cone is revolved to a lesser degree, such as 200 degrees instead of 359. The cone can be revolved to 360 degrees and ripped but that raises a whole nother problem because Inventor does not correctly refold a 360 ripped cone. File attached. By the way, the surface artifacts show up in the flat pattern as well.
Inventor 2012 SP2
Vault Collaboration 2013 SP1
Dell Precision T3500, Xeon W3503 2.4GHz, AMD FirePro V4900
Windows 7 64-bit, 8 GB RAM
I have tried everything. Its not really a cone, but same difference its a bottle neck. I want the company name around the bottle neck.
View 2 Replies View RelatedHow to draw with sheet metal rules centric cone? Ive spent hours on it and nothing, it always end up on ASM failure, or ceates the only one half( when sliced on asymetric way). This need to go in two halfs.
Ive tried:
two circles 1300 and 300, top circle centre moved from Y by 127mm on X axis.
contour roll will revolve on axis between circle centre points, than extrude something with cut and it is but the shape is an oval not circle.
Ive used loft command and slice command but only one side picke will work with flat pattern.
When i create a part in an assembly, i select a plane or face with the cursor, but then i select again a plane for the sketch.
Why this double selection, and what does the first selection do, if the part is actually sketched on the plane i selected in the second time.
Is there a way to anchor dimensions to views so that when the size changes, the dimensions retain their location in relation to the view?
View 5 Replies View RelatedHow does IV recognize iMate naming. I am trying to use specific named iMates on parts that when placed in the assembly that they can be placed in the correct postions. What I have run into is that no matter how I name the iMates I can place a part with one iMate name on a non-matching named iMate. Ex.- 1601-1 will mate with 2201-1 using the alt-Drag method. (These two iMates are both insert types.) This happens sometimes using the "Use iMate" checkbox on the place component dialog. I thought that the naming and type of iMate dictated what mates with what not just type.
View 5 Replies View RelatedIm just starting to look at I features to design, but even though my sketch is fully constrained when I place the iFeature with multiple references i can still move it using the arrows. How i could place them more accurately.
View 2 Replies View RelatedCreating a custom title block in innventor seems to be straight foward however when I save the new title block it offsets from the sheet, up and to the right. How do I get the title block to line up with the sheet
View 3 Replies View RelatedI am starting to model pipes for placement within assemblies.I could model the pipe and flanges in 1 part file but i thought this would take too long to create each flange individually so i modeled the pipe and flanges as separate part files and constrained them in a assembly file. How would you tackle this pipe work?
Future pipes will have different size/type flanges on a pipe depending on how it connects.
Is it possible to make the pipe in a single part file with the flange on 1 of the ends and with a command operation then move the flange to the others pipe ends?
my problem is that when I go to put in a gate (in this case a fan gate) of the type and shape shown below, I can't do it. It seems like gates have to only be above or below the parting line, rather than right on (and symmetrical about) it, and a fan gate (apparently) must always have a flat bottom.
(This is a snip of the drawing for the actual tool. I have to run some mold flow analysis on it before we authorize cutting steel. I could just model the whole 2-cavity assembly with gates and runners, and then lie to Inventor and tell it that the part actually has a sprue gate ... but I'd prefer to do it the right way.)
When creating views in Inventor 2013 the text displayed for example VIEW001 (1:1)VIEW 001 is placed under the view by default. I would like this to be above the view by default.
Autodesk Inventor Professional 2013 SP2 64-Bit Edition
Windows 7 HP Z400, Intel Xeon W3550 3.07GHz
12.0GB RAM, ATI FirePro V4800 (FireGL)
I am trying to edit the placement of vertical text within a dimension line - I wish for the text to be outside the dimension line not inside.
View 4 Replies View RelatedI'm using Inventor 2014.
I created a Punch Tool iFeature, everything seemed fine, I could save it without problems.
However, when I try to place it in a part with the Punch Tool, it says "The file has 0 volume changing features. To be a valid punch tool, the .ide file must contain at least 1 sketch-based feature."
I want to engrave the text 'TEST' all the way around this clonal object. When I use the emboss tool, selecting the option 'wrap to face,' it gives me an error message that the "face selected is not tangent to the profile plane."
I am using a work plane that is offset from the XY plane. I included a screen shot and the file that I am using (Inv. 2014)
I have a Wacom Bamboo Pen and Touch on Windows 7 64-bit and it appears to work fine in Windows on the desktop and in MS Paint. I can drag a box on the desktop, scribble in paint to my heart's delight, etc.
In PSP X4 the pen works...briefly. If I keep the pen down enough to make the red light appear on the tablet (to say it has detected the pen is close) it will happily draw in freehand with the paint/airbrush. If I lift the pen high enough to go out of detection range and put it back on the pad, PSP won't paint. The mouse will paint and the pen will work with tools like Pen or Flood Fill and in other apps but freehand doesn't work.
To get freehand back, I need to click on a button, tick box or other window control on the screen with the mouse. Then I can draw freehand again until the pen goes too high.
The PSP when it goes wrong like this is strange. Hovering the pen within detection range moves the cursor as normal, but on pressing down the 'dot' (or circle depending on brush size) stays where it is without making a stroke. The cursor moves around normally otherwise without applying anything to the image.
I've tried to re-install the drivers with a new copy from the manufacturer's site and removed Windows Tablet Support but nothing works to resolve this.
Am a very recent purchaser of Pro X6, and was wondering the best way to separate or 'lift' the darker areas of an image from lighter areas. I have attached an image as an example. Ideally, I'd like to separate entirely everything in the image that is yellow, from everything that is not.
View 14 Replies View RelatedI'm not sure what I'm doing wrong here. I have CS5 at work (CS6 at home is what's giving me an issue) and I could paint away for days if I wanted to, but with CS6 it randomly cuts out in the middle of using it.
View 4 Replies View RelatedI have an assembly that contains a part and a hole feature (the hole feature is at the assembly level). Using the api, I'm trying to get the hole location relative to the part's coordinate system in a without using the holeplacementdefinition.distance property, this way I can get the hole location regardless of the way it was defined.
View 2 Replies View RelatedHow to do a development of a frustum of a cone in auto cad?
I will prepare coal silo fabrication drawing in my office that is why i am asking.
I tried to convert the cone surface which is created by revolving line, to solid, but always fail. how to convert it? (Autocad 2013)
View 9 Replies View RelatedAssume that I have an odd pyramid 3D-solid say with a polygon basis that lies on a "floor". The apex was higher than the ceiling, so I "sliced" the pyramid to fit it right under the ceiling.
Now, I change my mind and want to make the ceiling slightly higher (say, 1"): after raising the ceiling I am left with a sliced pyramid that is cut 1"below the ceiling. Question is : what is the best way to re-extend the pyramid (and make it look like it was cut by the higher ceiling) ?
I cannot just "undo" because too many things happened in the meantime.
I can imagine re-creating the unsliced pyramid by press-pulling the upper sliced surface and then slice this extension with each side of the original sliced pyramid and ultimately re-slice with the new ceiling. Can I do better / faster than that ?
I am trying to place some objects on a cone. But i can't get it to work. The idea is that the 6 objects should be fitted on the cone so that they are placed all around the cone. But i can't get them to align with the angle of the cone. I have tried the 3D align, but this just doesn't work for me.
View 9 Replies View RelatedI have started a project and have a somewhat unusual condition. I have a structure with a Conical Roof. We are putting a parapet around this roof. With the parapet, we are also going to create 4 individual structures that direct water/rain flow to scuppers that will be fabricated into the parapet. Below is a sketch of our condition. How to get the shape of a line that follows the face of a cone. Obviously, this line is not projected to the center of the cone, so it is not just a straight line. I am imagining either a radial cut piece, or a complex/multiple radial cut piece. I don't really know how to put it into words exactly.... Take a look at the sketch.
Cone Info.jpg
How can I draw a 3d arrow in autocad 2012? (where the arrow head is a cone, or something that appears in all view angles).
Assuming the answer will be a cone and line grouped, how can I rotate them (I seem to be able to rotate only in the xy plane).
I am currently in the process of doing some traffic management drawings and need some road signs, but mainly im after some free cone software apparently. You can get some really good software, free if possible if not then the cheapest available. This is for autocad 2008.
View 9 Replies View Related