I am trying to add a list of External References to MTEXT. The diesel expression $(xrefs) works fine within RTEXT but when I enter it into MTEXT the result shows "$(XREFS)??
View 2 Replies
I have an attribute definition and I need to add its value to an mtext. I added it in mtext insert field it is ok, every thinks work fine it is only needs a regen but it is not a problem.
The problem is when my mtext and att in a block regen does not work in model space, I had to enter block and regen. Is there any way to do it without entrance in block editor?
I attached a simple example.
Is it possible to contol the visibility state of an external referenced drawing? I have an architectural plan drawing that uses a titlesheet drawing as an external reference. In my civil plan i want to use a different title sheet. Instead of having a different titlesheet drawing for the civil drawing i was wondering if i could turn my titlesheet drawing into a dynamic block. In my architectural drawing i would see visibility state #1 & in my civil drawing i would see visibility state #2.
View 1 Replies View RelatedThe standard AutoCAD Find & Replace dialog doesn't seem to work on a dynamic block's visibility states. I have quite a few blocks with 8-10 visibilities in each one that I need to change.
View 3 Replies View RelatedI needed to use an xref so loaded up the external references box to view all available xrefs. Since i did this i cant get rid of the xref box. Its there whenever i load cad up, load a new drawing and when switching clean screen on and off. Ive tried the close button in the top corner but it still returns.
View 8 Replies View RelatedHow to use External references?? i have worked in autocad but i dont know how to use this command, i have to do about 250 drawings of External references.
View 3 Replies View RelatedI want to load the external references in the drawing, how to implement this program?
I returned to the drawing path and the way I want to load it using the insertion point.The code error is probably somewhere not understand where.
[CommandMethod("TDMSXREF", CommandFlags.Session)]
publicvoid TDMSXREF()
{
Document doc = Application.DocumentManager.MdiActiveDocument;
Database db = doc.Database;
Editor ed = doc.Editor;
[code].....
Is there a procedure or command to use on an opened drawing to see if the drawing is used as an external reference anywhere else? For example, can I open Drawing A and determine whether it is used as an external reference in Drawing B without going to Drawing B and looking at the external references palette?
View 1 Replies View RelatedI've been asked to create several drawings using one external reference which contains doors, bund walls, lighting etc. My question is how do I take this external reference and create several new drawings when I cant even turn layers on or off once I have inserted it onto my new page?
View 4 Replies View RelatedI've made annotative blocks and I've made dynamic blocks... My intent is to integrate both but I can't find a way to move dynamic block parameters separately at different annotative scales.
In other words, if I insert an annotative dimension and add multiple scales I can move the dimension grips independently at each scale. If I insert a dynamic block I want to be able to use the dynamic block's action "grips" to do the same. However, with a dynamic block, if I move a stretch action at one annotation scale it moves the action at all annotation scales.
The attached file shows a simple example.
I have a DWG file with wipeouts. When I use the files as external references in another DWG and print to PDF the wipeouts do not work and all that is seen is the wipeout line. Is there a way to have the PDF have the wipeouts appear as they should?
View 3 Replies View RelatedI use this palette all the time and keep the icon displayed (in hidden form) on every session that I open. I started AutoCad this morning and "external reference" icon was not displayed on the screen. I went to the tools tab and selected the external reference palette. A box was displayed that could not be hidden and all screen function were stopped until I closed this box.
I went to customize tool palettes and compared it to the properties palette and they looked the same. I want to get my external reference palette function back to the way it was.
I'm trying to adjust the properties of some block objects in Mspace. When the file contains external references the function fails, when it has none it works perfectly.
Dim modelSpace As BlockTableRecord = DirectCast(M_trans.GetObject(SymbolUtilityServices.GetBlockModelSpaceId(db), OpenMode.ForRead), BlockTableRecord)
For Each id As ObjectId In modelSpace
Dim ent As Autodesk.AutoCAD.DatabaseServices.Entity = DirectCast(M_trans.GetObject(id, OpenMode.ForWrite), Autodesk.AutoCAD.DatabaseServices.Entity)
ent.Color = Color.FromColorIndex(ColorMethod.ByLayer, 256)
Using the above to get all objectid's and filter through them then using:
If TypeOf ent Is BlockReference Then
Dim br As BlockReference = DirectCast(ent, BlockReference)
Dim btr As BlockTableRecord = DirectCast(M_trans.GetObject(br.BlockTableRecord, OpenMode.ForRead), BlockTableRecord)
If Not btr.IsFromExternalReference Then
Here is the background.
A "MODEL" drawing exists that contains only the surface model. The surface model is data referenced into a "LABEL" drawing that contains the surface style (contours), contour labels, and spot elevations. This "LABEL" drawing is xref-ed into a "SHEET" drawing that contains the title block and some other xrefs containing the proposed layout, ex cond, etc..
When I open the "LABELS" drawing, the data reference works. My problem is that when I open the "SHEET" drawing, the contour labels and spot elevations cannot find the referenced surface and just contain a string of 20 or so characters.
I already have a workaround. If I open the "SHEET" drawing, then open the "LABELS" drawing and save it, I can reload the "LABELS" drawing within the "SHEET" drawing and the problem is solved.
HOWEVER, I have a bunch of sheets that I want to publish, and publish does not work when you have to open the file and re-reference everything. Is there anyway to get this reference working correctly so that I do not have to open multiple drawings to get my data correct?
FYI, I have already tried resetting my data shortcuts project folder, validating data shortcuts, etc. in the "LABELS" and "SHEET" drawings.
Civil 3D 2012, SP 2.1
I have created a dynamic block with several visiblility states. The block works great for what I need it for. however, I am trying to add one more action to the block but am having issues.
This block is essentially a 24" retail cabinet with the visibility states showing the different drawer and shelf configurations. I want to be able to lengthen the cabinet in 24" increments and have the visibility show for each 24" section.....e.g. I want a 10' cabinet so I bring in the 24" starter block. Then stretch the cabinet to the 10' mark, then I can chose any drawer/shelve config for each 24" section (they are all different).
I can get the block to stretch in 24" sections....no problem.....i just want the visibility state to be duplicated as well for each section. Now as it stretches, there is only one Vis state and it only populates the first cabinet.
I could do this by copying the block over and over 5 times.....but I am hoping there is a way to make this dynamic.
I have a block I am making into a Dynamic Block. I will be adding in different visibility states. Depending on the visibility state the block would need to be inserted from a different point.
My question is, is it possible to add multiple insertion points to a dynamic block so depending on the visibility state it defaults to the correct insertion point?
is it possible to retrieve the names of all the nested external references, and how should it be done?
View 2 Replies View RelatedIs there a way to localize all external material references? For instants I created a framing square with the proper materials assigned. When merged with another file it looses its bit map image placement so have to re-fit every thing again.
View 8 Replies View RelatedI'm having is that this is happening with a dynamic block. I don't know how it got this way...some 'genius' in my office went into this file and screwed something up, and saved it...so now I'm left with the task of fixing it.
When I go into the block, it opens as a regular drawing, with a dynamic block inside of it...as opposed to opening in the block editor. I just need to know how to get this back to the way it should be, without having to redraw the entire thing from scratch. I made a few scrap-copies of the drawing to fool around with and I can't find a solution. I tried deleting the block and purging it, I tried exploding it, and I tried saving it directly from the block editor...nothing worked.
not sure if it a stamp plot item but I am trying to list all the x-references that are associated with a particular drawing on the plot sheet?
View 5 Replies View RelatedI have a problem with selecting all references to a specific dynamic block. When I use the filter below only block “D2” is selected, which is not a dynamic block, Block "Bulb120227” which is a dyn block is not
Dim values() As TypedValue = { _
New TypedValue(0, "INSERT"), _
New TypedValue(-4, "<OR"), _
New TypedValue(2, "D2"), _
New TypedValue(2, "Bulb120227"), _
New TypedValue(-4, "OR>") _
}
How should the filter be done to filter out the dyn block that I want several block should be filtered out in one selection.If it is possible to achieve with just a filter at all?
is there a way to make dynamic blocks stretchable similar to a mleader,
the blocks i create are only stretchable by grips, and not by crossing
(i am using linear or point parameter stretches)
Is there anyway to link standard AutoCAD Grips and there commands to Dynamic Block Actions? I want to stretch an arc by its midpoint grip. This accomplishes something that no other commands do.
View 4 Replies View RelatedI'm searching an external RTF-Editor which is quicker then "MS Word" and better then the internal editor. Some applications use this RTF-modules.
Can one of these used by Autocad?
Is it possible to edit the standard pull down symbols list. There are lots to choose from but I would like to add a favorite to the current list.
View 9 Replies View RelatedSo I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies View RelatedI need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies View Related
