I am using AutoCAD Civil 3D 2012 and Adobe X Pro. When I print to PDF (using plotter DWG to PDF) the hatching for the slopes analysis does not show up. I have other hatching in the plan and that shows up, along with the outline for the slopes. Its just the actually slope hatching that doesn't show up.
View 2 RepliesCan you not perform a slope-slope intercept to place a PVI? Essentially holding the sta and elev of the PVI's directly before and after the PVI of interest and changing the grade in and out so that the sta and elev of the PVI of interest are changed.
View 2 Replies View RelatedCan't figure out how to match gutter slope to outside lane super subassembly slope. Have super eop targeting a feature line with elevations, but when i check section editor gutter slope doesn't match pavement slope.
Civil3D 2013
Windows 7, 64 bit
Intel i7 2600 @ 3.40Ghz
16 GB RAM
Nvidia Quadro 600
i need a shoulder subassembly that varies slope in relation to the lane superelevation slope. i know that i can get a subassembly for the shoulder that will follow the alignment superelevation xml data but in my case i can't use it because we are just adding a shoulder to an existing road. we're not changing the superelevation of the existing road, just milling and overlaying and widening. right now i've created a profile of the outside edge of the shoulder that gives me the correct shoulder slope but whenever i change my centerline profile i have to redo the shoulder profiles which is a real time suck.
View 9 Replies View RelatedI am in the process of transitioning from land desktop to Civil 3D. I design roads in steep terrain and sometimes need to have my catch (daylight) slopes change. So my question is, how do I change a daylight slope at a specified depth? For example, from the shoulder of the road I want a 3:1 fill slope to a depth of 10 feet than change to a 2:1 slope until it catches the existing surface. Can this be built into a subassembly such that if the fill is less than 10 feet it will daylight correctly at a 3:1 and if the depth is greater than 10 feet then it carries the 3:1 for 10 vertical feet and then changes to the 2:1 until it daylights?
View 9 Replies View RelatedIs it possible to change the cut and fill pattern from solid bands of colour to bands of colour cross hatch (for example)? The reason for this is, when printing the drawing uses a lot of ink.
View 8 Replies View RelatedI have a surface made out of 3Dfaces as shown in the .jpg attachment i added. I would like to have it hatched. What are my options?
I use Civil 2012 and have experience with AutoCAD plain, but only try to learn Civil 3D at the moment.
I am using MEP 2012, I have arch back rounds on in a Xref. Everything seems to be fine and work well. When we go to print the drawing on with the xref on it is barely visible. If I open the xref up and print it comes out fine. I have inserted the xref to its own layer.I do not know what to do from here.
View 9 Replies View RelatedI discovered a weird thing that seems like a bug...I tried to hatch manually while in profile view (couldn't figure out how to do what I want with the profile view hatching options) and it seems that if I try to make one hatch (by picking internal points) that includes multiple structure profiles on the same profile view, the first structure profile for that profile view works as a hatch boundary, but subsequent structure profiles are basically ignored if I keep trying to pick internal points to make a composite hatch.
I assume it's because of this same bug that I can't create a hatch by choosing boundary objects and using two structure profiles in the same profile view as boundary objects.
how to hatch using the profile view hatching and to use a pipe network as a boundary, that would also be useful.
if I hatch by picking internal points, and pick one area with a structure profile as part of the boundary, and then I pick a similar area in a different profile view, everything works fine...it's just the second (and though I don't have more than 2 structures per profile view in my drawing, I would assume any subsequent) structure profiles that I try to use as hatch boundaries that AutoCAD is basically ignoring.
I'm using C3D 09 with all the updates. OK, now that those are addressed, I am having an issue with my pipe hatching dissappearing when I connect it to a structure. See the two attached pics for clarity.
View 4 Replies View RelatedIs there a way for C3D 2013 to automatically hatch (with a style) in the profile view the area from the FG to top of pipes (Sanitary, Storm or Water). Currently we go old school with isolating the linework in the profile and hatching it manually. The interesting thing is the hatch still recognizes the grid in the profile view even though we've frozen the grid and other linework. AND we must put a line on the top of the pipe, or the hatching goes to the next "grid" of the profile.
Would be nice to get it to generate the hatch much the same way it does for the profile view with Cut area or Fill area or Multi boundaries.
I have searched the Help fine in Civil 3D, I have searched the tutorials and Knowledge Base online, I have searched the Mastering AutoCAD Civil 3D manual, and I can not fine how to turn on hatching in Section Views. I'm currently running Civil 3D 2013.
View 5 Replies View RelatedI am trying to show cut and fill hatching in the profile views but the hatching doesn't show up. I've tried changing the hatching styles, the scale, the colors, etc. but it doesn't seem to be working.
View 4 Replies View RelatedThe undefined areas of a slope map now have a hatch to them and are plotting black. This map was created a month ago in 2012 without issues, upgraded to 2014 and now the undefined range has hatch!
View 8 Replies View RelatedI have a TIN Surface, and I want to get the slope at a point (know X and Y).
Working Civil 3d 2010 and API.NET
I have a simple driveway corridor along a steep hillside. For cut, I would like to have a negative slope away from the shoulder edge. I have tried numerous approaches and all 'cut' reverts to positive. I searched and found no clear answer. It's such a short driveway, I can 'fake' it in, but I would like to calculate quantities.
Using 2012 sp1, 64bit, windows 7
Is there a way to create hatching for the slopes surface style instead of using solid colors?
View 2 Replies View RelatedI've got a surface that displays contours correctly. When I go to Surface Properties-Analysis tab, I can set an arbitrary number of ranges for contours, directions, elevations, slope arrows, etc, and they display correctly.
I can set an arbitrary number of ranges in the slope range box too, but when I click the Analyze button, Civil 3D 2014 hotfix 1 only displays two slope ranges: 0% to 2979736.0077% and 2979736.0077% to 99999900.0001%. (!)
Can I automatically have my slope patterns introduced with a command like matchprop or something similar ?
I have 284 streets and it's getting ages to finish the slope patterns on every street. Civil Engineer / Infrastructure of metropolitan transports. URL....
I'm trying to match an existing slope design that has a soft rounded off top of slope. The toe (green) is a feature line and I'm using a 1-1/2:1 slope to natural surface grading rule. You can see the rounded contours in blue that I am trying to match.
View 7 Replies View Relatedin my link "link slope to surface", i have the slope set to -2.00%. in the cross sections, it is at a +2.00%. why is this thing not linking at the defined -2%? see image.
View 1 Replies View RelatedI need to project a surface/grading (or something of that nature) across my berm and have it intersect with the inside bank. This is better explained if you see the attached image. In the plan view you see 4 featurelines. Outside TOE, outside TOB, inside TOB then inside TOE. I need to project the outside TOE across the berm (shown in the section view) then create a new featureline where the line and inside slope of the berm intersect. Note that all the elevation shots vary as does the widths across the berm. What's the best way to do this?
View 9 Replies View RelatedWhat formula Civil3D uses to calculate the average slope of a surface?
The formula I am using is S = I*L/A
S = Average Slope
I = Contour Invertval
L = Length of Contours (ft)
A = Area of parcel (sq. ft)
I just had to do four parcel calcs and the percentage I find using the formula is always 1-3% lower than the percentage Civil3D spits out. I can't find anything about how Civil3D arrives at that number, it just appears. I assume that Civil3D is more accurate but I can't give that number to a client without knowing how the program arrived there.
I created a profile view in order to create a corridor, I want the profile PVI stations to be on the same plane,
View 1 Replies View RelatedI need to have a subassembly for a superelevation where the lane and base slope to the left and the bottom of the sub-base will slope to the right. I was using the LanSuperelevationAOR subassembly, which worked fine with my superelevation when the lane, base and sub-base were all sloping the the left, now I need to edit the slope of the sub-base only to slope back to the right at a -2%.
Windows 7 x 64
8GB Ram
Intel Xeon CRU 4 Core @ 3.07GHz
Civil 3D 2012 .....
I can not get the slope analysis to come up with 10 slope ranges. My ranges are set to 10, but my Range details populate to 22? Screen Cap included. I've tried this with Equal Interval, Quartile, and Standard Deviation. Nothing will create 10 intervals.
My "slope analysis" surface style is set to show Slope, with the range set to 10. In surface properties, my range is set to 10.
I use slope symbols instead of contours to keep my maps less busy. Unfortunately I can only change my cut style and fill style to slope symbols with grading by right clicking on the little diamond in the grading and selecting grading properties.
I have created a surface with 3d poly lines not by creating grading and got contours that way, How can I create the slope symbols in a surface. I tried xploding them and then creating a block and using the measure tool on the 3d polylines but it doesn't do anything.
Picture 01 is the contours
Picture 1 is the contours turned off and cut/fill styles turned to slope symbols.
Please find the attached picture. It shows a surface with its data points. I extended the surface to the outer boarder shown by kriging. The slope of the surface that was added with the extension (past the data points) has an upward slope that was generated. I need the surface to stay level with the data points that are there.
How to avoid that added slope when extending a surface?
Trying to add slope markings on my corridors, and the only way I can find is to do it in the Corridor properties > Slope markings, then click add slope pattern, which asks you to select featurelines top and bottom of slope. Surely there is a way to simply switch on or off slope markings where in cut or fill?
View 7 Replies View RelatedI need to be able to do a slope analysis on a surface, but I need to have it calculate the slope in a direction - east and north. Any way to do it? Maybe even if there is a quick way to apply slope labels to a surface based on a grid - say the slope from N0.00, E0.00 to N0.00 to E 25.00
View 9 Replies View RelatedI am using Civil 3d 2013 and I am trying to calculate the superelevation information in which the curve will max at 2%. Is there a way in which the superelevation can be calculated using the superelevation wizard in which a 2% SE is the max? So far it will only let me use the SE for 4% local roads and I have to edit it using the SE layout.
View 3 Replies View Related