AutoCAD Civil 3D :: Moving Curb Grades In Profile View?
Aug 20, 2012
I am having a problem with moving my profile grades. I go to Utilities under Corridors and create a profile for the left and right curb. They show up in my Alignment Profile, but when I click on one to move it, it disappears. When I type regen, it shows back up. I am trying to set my crossection grades in my Multiple Section Views. I first create my Profile from Surface, then do a proposed centerline grade by Draw tangents with curves. I create the corridor, put in the regions, go to corridor properties and pick the right and left corridor lines I have created. Then I set the existing surface and attach it to my profile. I create the sample lines and the Multi Section Views. Where am I screwing up?
View 4 Replies
ADVERTISEMENT
Feb 28, 2011
I try to make curb return profile without profile view like a intersect command.
I was make curb return alignment but I can not find profile command without profile view.
View 6 Replies
View Related
Jul 20, 2012
I tried moving a Profile View and even though I selected everything at once and selected a base point and destination point, the Profile View Station and Elevation labels moved with a different offset than the Profile View itself. ?
Civil 3D 2012
View 2 Replies
View Related
Jun 4, 2013
how to label Profile Grades at a certain station other than high points, low points, pvis...etc?
I need to label an offset station with profile grades and cant seem to figure it out.
Civil 3D 2013
View 7 Replies
View Related
Nov 6, 2012
I am trying to get a street assembly to follow a top of curb profile. The profile is at the face of curb. The centerline of the street is my assembly target profile and alignment. I do not want to create an alignment for the curb. The curb profile is based on the centerline alignment. I can't figure out how to get a link that will track the curb profile at the face of curb.
View 4 Replies
View Related
Jul 6, 2012
we use three line road profiles. If there is a bus pullout or lane transition we show the curb profile based on centerline stationing. I'm able to generate a the corridor using a transition lane assembly from centerline and targeting a widened offset alignment or just a feature line. I can import the corridor curb feature line into a profile which would be a perfect solution, but it is all truncated. (i.e. no vertical curves) I can create a profile of the offset alignment, but the stationing doesn't match centerline.
How can I either generate a non trunidicated profile from the corridor for my curb profiles? How can create a design profile of a transition/pullout curb line that I can target and plot against centerline stationing?
View 4 Replies
View Related
Apr 4, 2012
We sre doing 3 line profiles for a road and the left and right curb should be .13' lower than the centerline elevation. In many cases we are getting .14' or sometimes more or less. We tried resampling the cooridor with a tighter interval but still the same results.
View 9 Replies
View Related
Nov 4, 2013
I'm working with a structure profile label style and it seems like the only way to anchor the position of the label is based on offsets from the structure itself... Any way to position the label based on the top of the profile view, so that I could make all of my labels horizontally aligned above the profile view?
View 9 Replies
View Related
Nov 22, 2013
I have a 10 foot profile view and a 15 foot manhole. I want to show the manhole but not the bottom 5 feet. It is extending beyond my profile view.
Civil 3D 2014 SP1
Windows 7 Professional
Intel Core Quad Q9650 3.0 GHz
8 GB, 64-bit
View 7 Replies
View Related
Jul 24, 2012
I have yet to produce a profile. I created a polyline and turned it into an alignment.
Looking at alignment Sample(3), I see that it is not superimposed over your surface. The polylines are, but the alignment is not. That will disallow creation of a surface profile.
Is the sample5 an alignment that sits on the surface? how come there is still no profile?
View 3 Replies
View Related
Nov 28, 2012
Attached are survey points that created the surface of a road embankment portion that caved-in. The road is very near a reservoir shoreline.
1. How can a surface profile be produce? I/'ve use line to change it into an alignement and then create a proile , then a profile view. But the the surface profile is missing.
2.the points having higher elevation are the top edge( road level) of the cave-n . A few few shots were take before the shorline elevations.
3. What the best way to come up with the rock volume to fill the cave-in given this surveying points., Also the shoreline elevation will be lowered some more while work is being done since the fill is not allowed to fall in the reservoir.
View 2 Replies
View Related
Jul 31, 2013
A tabular data sheet for profiles could be very interesting.
Civil 3D (2013)
View 9 Replies
View Related
Jan 22, 2013
I have an issue with a profile referenced into a plan sheet that is shifted when I view it in the plan sheet viewport. The profile stationing is correct in the profile dwg file and in the plan sheet dwg it is referenced into. But when I switch from model space to paper space in my layout sheet (the file the profile dwg is referenced into) the profile moves to the wrong station within my profile view in paper space.
The profile start station is 0+00, but it shifts to -1+00 within the viewport of my layout sheet.
The scales are the same between the dwg files (50) and the Annotation scale matches the dwg scales.
View 2 Replies
View Related
Jul 24, 2012
I am a C3D newbie who used ground survey points (Serrano_EG_surface) that generated a Civil 3D surface. The white line is consist of arc segments that I turned into polylines and then into individual CL alignments. The first alignment ,which has its left and right offsets do not generate the profile view that I needed to be created. There was a prompt asking for a profile to choose, but I don't know where in the drawing or in the propector panel to click on.
1. Are the ground survey points good enough so that any alignments over the those areas can provide me a surface profile, a design profile, cross sections every 50 feet, so that I can submit a preliminary drawing for environmental permitting. ?
2. When I check the object browser, the aligments preceding each other are not in the same elevation it seems. Do I have to to transform each of the polylines first into a 3d polyline and then an alignment so that I can create a profile.
3. Eventually , I wish to connect all these alignments to model a 1.5 mile rural road (more like an access road to a water reservoir).
4. What's a best techniques to keep track of modeling a road.This question pertains to e.g the object browser as one of the useful aid. I've also used the inquiry tool but not used it for its full potential.
View 2 Replies
View Related
Dec 20, 2012
I was wondering if after drawing an alignment, creating a profile, and profile view, is there a way I can mark items along the alignment so they could show up in the profile view. I am laying out a pipeline and want to have the profile display a marker for items such as tees, elbows, reducers and other items. The marker I would like to use will be something like the vertical style grade break markers.
Also on a side note, as each of these items will have a different name, is there a way that I can add these markers and then have each one with a unique name?
View 9 Replies
View Related
Nov 28, 2012
1. I had trouble with profile view of the alignment line shown. What step am i missing? Are there things that is turned off?
2. How can I best come up with the right volume to fill.
3. Do I need to learn the grading tools? or could i get buy with a section profile from the alignment. ( it is not even an alignment yet)
4. How to I render a rock fill in this cave-in.
The attached aerial image , has survey or cogo points that are imported to surface, to become surface points. . So I wanted to create a surface profile below and an outline of fill above it. Iideally the side profile would look like a trapezoid, where the base is the surface proile and top would be the design embankment.
But the reason , a surveying crew went down and took shots at the shoreline and a couple shots around the cave-in walls (higher elevation on the cave-in wall cannot be surveyed, although I coud have used a laser , did not) is so that a more accurate volume of the cave in can be obtained. I tried to label how far the road edge is from edge of the cave-in . Norice the higher elevations are the top edge around the cave in area.
The ouline for the embankment will be a mild slope then breaks to a more steep slope. like 4 :1 , then 1.5:1
View 5 Replies
View Related
Jan 18, 2013
I was given a horizontal centerline of a 5 mile bike path. We have to stake all the even stationing every 50 feet and all the VPC's and VPT's with vertical elevation. I have created the horizontal profile and also the vertical profile including all the vertical curve information. Is there an easy way to incorporate the elevation information back into the plan view so I can create points that carry x,y & z points that I can transfer out of autocad as a .txt file so we can upload it on our gps equipment?
View 9 Replies
View Related
May 29, 2013
Is there a way to easily add an object from a profile view to a plan view? I have developed a pipeline profile that has high and low points and I would like to show these points on the plan views.
View 9 Replies
View Related
Oct 18, 2012
Moving profile or alignment, I’m not sure why moving profile introduces a problem! Some data is missed!
View 9 Replies
View Related
Dec 3, 2013
The project I am working on requires shoulders sloperd at -1.5% to -3.0%. Is it possible to set up an assembly and corridor to cut anything above -1.5% and fill anything below -3.0%?
If I can show both the cut and fill in the same drawing, that would be ideal.
AutoCAD Civil 3D 2012
View 1 Replies
View Related
Apr 7, 2010
Any way to raise/lower a surface, but is there a way to offset a surface basically 1m (to make it easy) perpendicular to all grades? Because when you raise/lower a surface, if you have a 3:1 slope, it will raise/lower it vertical 1m or so, but then the perpendicular distance between the 2 surfaces is less then 1m.
View 9 Replies
View Related
Dec 25, 2012
I imported Google earth surface (at eye alt 600m) to civil 3d 2012 and created an alignment of length 181m.
When I exported same alignment to Google earth , it showed the length as 190m ( the difference increases with increase in length of alignment) And also the profile view of the alignment in the Civil D & Google earth varies.
View 4 Replies
View Related
Jul 9, 2012
using Civil 3d version 2012...Want to add existing and proposed profile grades to cross sections for the eastbound and westbound lanes. I have an alignment established for each
View 2 Replies
View Related
Mar 14, 2012
I am trying to get the existing and proposed grade from my surfaces to show up in the center bottom of my cross sections. I am working with the CL elevations band style and trying to set up so that major and minor increments are the surface elevations. Am I going about this wrong? I went in to the compose label tab and selected for the text to be section 1 elevation and section 2 elevation. When I am at the section view properties box / bands tab, all that shows up is my existing surface. I have created sample lines and a corridor. I have also created a surface from the corridor.
View 1 Replies
View Related
Dec 31, 2013
We have recently upgrading from 2012 to 2014. Several of our jobs are not reading the surface when we open the drawing. We have to force the sync of the surface and then the grades display.
AutoCAD Civil 3D 2014
HP Z620 Workstation 64-bit
Duel Intel Xeon E5-2620 @ 2.00 GHz
Ram: 48 GB
View 6 Replies
View Related
May 24, 2012
C3D 2012..Have a profile I'd like to have the PC, PT shown. (No Problem)But in doing so it also puts the PI'S of each of these curves in the profile view.
Is there a way to turn off the PI's and leave the PC's and PT's on?
View 6 Replies
View Related
Nov 6, 2012
I am using the profile sample VB.net program to create an alignment, profile view and profile. The profile view defaults to start at station -0+25. I want to set the Profile View starting station based on the "Align_strt_sta" value I have defined based on the Alignment Stationing. I have tried the .StationStart() shown below, but I just get a unhandled exception.
' Create the profile view and add it to the alignment's ' collection of profile views. If oProfileView Is Nothing Then id = ProfileView.Create(m_CivilDoc, Prof_View_Name, PROFILEVIEW_BANDSET_STYLE_NAME, Align_Name, pviewposition) oProfileView = pviewTransaction.GetObject(id, OpenMode.ForWrite) End If 'oProfileView.StationStart() = Align_Strt_Sta oProfileView.Description = "Profile view of alignment '" & m_SampleAlignment.Name & "'" oProfileView.StyleName = PROFILE_VIEW_STYLE_NAME
View 1 Replies
View Related
Nov 12, 2013
I discovered a weird thing that seems like a bug...I tried to hatch manually while in profile view (couldn't figure out how to do what I want with the profile view hatching options) and it seems that if I try to make one hatch (by picking internal points) that includes multiple structure profiles on the same profile view, the first structure profile for that profile view works as a hatch boundary, but subsequent structure profiles are basically ignored if I keep trying to pick internal points to make a composite hatch.
I assume it's because of this same bug that I can't create a hatch by choosing boundary objects and using two structure profiles in the same profile view as boundary objects.
how to hatch using the profile view hatching and to use a pipe network as a boundary, that would also be useful.
if I hatch by picking internal points, and pick one area with a structure profile as part of the boundary, and then I pick a similar area in a different profile view, everything works fine...it's just the second (and though I don't have more than 2 structures per profile view in my drawing, I would assume any subsequent) structure profiles that I try to use as hatch boundaries that AutoCAD is basically ignoring.
View 7 Replies
View Related
Aug 13, 2013
When inserting a piece of my watermain into my profile view, the watermain is not stopping at the edge of the first profile view. Instead it just continues out of the view. See attachment. When I change the style of the pipe to just centre line I do not have this issue. It seems the hatching is the issue.
View 1 Replies
View Related
May 7, 2013
I want to have the ability of take measures on my profile view.
The tool would consider the vertical exaggeration and give me the right distance and slope .
Civil 3D (2013)
View 3 Replies
View Related
May 22, 2013
How to upload Civil 3d Sample profile with full band
View 1 Replies
View Related
