dynamic block in a drawing - when i make a change in the block editor, it doesn`t apply in the model space although i save all the changes. There is also another dynamic block and this time everything is working properly - all the saved changes appear in the model space. The only difference between the two blocks is that the first one has attributes. I think attributes should not be the reason for not applying changes, but i just don't know.
My drawing- block is a little bit complicated, it contains few actions and parameters and everytime i open block editor to add, or to modify some action I can't see my drawing because actions grips and parameters grips obscure my drawing. I tried to refresh layout but it doesn't work.
Attached is a dynamic block of a smoke/c.o. detector. I have a few of these on a floor plan and at times the entire floor plan needs to be mirrored. I would like the text itself to mirror as well so I don't have to select each dynamic block and mirror it again to read correctly.
I have mirrtext set to 0. I have read that creating attributes will solve this problem however I have created attributes in the dynamic block and I still cannot get it to read correctly when mirrored.
I have created a library of dynamic blocks in AutoCad10. When I craeted them I could click on the Grip for a Linear Parameter that was associated with a Stretch Action and the current value would be displayed (Example: The width of a block). I could type in a new value and the block would stretch to that value. Something changed this week when I attempted to use my blocks. When I click on the Grip no dimension is displayed. The command line shows "Specify point location or [Base point/Undo/Exit]". I can drag the grip to change my block but I cannot simply type in a new dimension as before.
There doesn't seem to be an issue with this block when I open it with the block editor in the drawing where it was created. However, if I insert it into another drawing, it comes in as a block but when I select it, only the insertion point grip is visible. What happened to the parameters and actions? Oh they're still there but I have to open the block editor again for that block and then they display a great distance away from the block itself. This is all in model space with no change to the scale of the block upon insertion.
If I erase the parameters and actions and recreate them, the block behaves correctly in that second drawing but there is still the problem with the original block in my library.The attachment is supposed to be for a portion of metal deck that can be arrayed to whatever length is requied.
I am trying to insert a block into a drawing that uses dynamic blocks. I want the block to be associated to the dynamic block, so that when I alter a linear stretch parameter on the dynamic block it moves the other block.
I am probably missing something obvious, but have now googled my mind into a numb state and can't make any more progress.
I need simple code to do just one thing, inserting a dynamic block that is stored in a separate file on my computer (like C:/base/b-22) in the drawing that I'm currently using. For example, I have a windows form with a list box with names of many dynamic blocks that are stored on my c drive, I would like to pick a block with a name and upon a click event of a button or other will go get this block from a separate file and insert it in the drawing I'm currently using, and would need to be able to pick the point of where I want the block to go. I'm using autocad 2010 with visual studio 2008- using the new autocad .net language.
I have searched high and low and still could not find a tutorial to really explain how to create a drawing title with attributes (Detail Number, Sheet Number, Detail Title, Detail Scale). All I find are on creating dynamic block, which I could achieve, but I need one for a block that has (or will have) attributes.
I was able to find a tutorial on attributed door numbers, but it does not work for drawing titles that has attributes. GOAL: I would like to have all my seven drawing titles in one file and to be able to stretch the leg of any selected title to a desired length.
We currently have a bunch of Lisp programs to create drawings but I am interested in exploring how I can maybe use Lisp with either dynamic blocks or parametric drawings. I just don't know which would make more sense. Currently we have programs where we enter things like width, height, leg or radius, bars wide and high etc and it creates a drawing like the one I've attached. I know that if I can create this drawing as a dynamic block or a parametric drawing, then when there are revisions, I don't need to create the drawing again. I can just adjust the parameter or the dynamic block. What makes the most sense, a dynamic block or a parametric drawing? I should note that I'd still like to use autolisp to create the initial drawing (or insert the block) since that's what the users are used to.
It's possible to create a dynamic block programatically? I want to create a command that captures different selection sets of drawing objects and assign them to different Visibility States of a new block deffinition, on run time.
I created the attached block to add spot elevations to a drawing. The block has attributes allowing elevations to be manually typed in, but also includes many dynamic features for rotation, lengthening, mirroring, etc. The block was created as an annotative block.
The block and all of its features work perfect as long as the dynamic features (rotation, etc) are not used after additional annotative scales are added. I often times have a drawing set at 1:10 or 1:20 scale and need to do an enlarged detail at 1:5.
What I would like to do is have this block set at 1:10 scale and 1:5 scale and manually rotate it (ideally using the dynamic features) at different angles for each scale. Is this possible and if so, why is it not working with this block? This works flawlessly when using annotative multileaders, so why shouldn't it work with blocks or is this just too labor intensive for the software?
I have also tried attsync, etc. and often times when rotating at different annotative scales, the text attributes go "bonkers" for the opposing scale when applying attsync.
I created a Dynamic Block that works perfectly, however when I try to add it to my tool pallet, I get an error message that reads "Block XXX is not found in source drawing. If the source drawing is currently open in the editor please save your drawing."
I'm not in the block editor, and I've saved it multiple times before I tried doing this. I've even closed AutoCAD and reopened it and I'm still getting the same results. I've been able to add many other blocks to my tool pallet, but it just will not accept this one.
I was presented with a little renovation project and need to setup my own drawing. I've worked on CAD for a number of years while at a structural firm, an engineering firm and took classes in school but one thing I never had to do was setup was my own professional drawing from scratch. I know enough that it's crucial I start off on the foot. The engineering firm I worked at had everything ready so whenever I used CAD it was in an existing drawing or preparing a detail which the drafters imported. When I did some drafting work for an architect, he also had the drawing setup for me.
Since I'm now on my own I need to setup my own template drawing with a title block, layers, etc. Whats the best route for setting up my own sheets?
At my firm we always worked in a 1:1 scale & engineering units but since I'm doing floor plans for renovation work I plan on using the industry standard.
Is it possible to have a dynamic block with text which, when inserted into a drawing, will show the text orientation matched to the layout? I have a non-dynamic block which is simply a donut and a piece of text. When I insert it into a drawing, the text orientation will change to suit the orientation of the layout. I created another block with the same entities but I also added a couple of lines extending out from the center of the donut. I added stretch and rotation actions in order to rotate and stretch the lines. I also gave the block visibility states so that either one or two lines would appear (the block is a utility pole,by the way, with the lines representing guy wires). When I insert the dynamic block into a drawing, I cannot get the text to match the orientation of the viewport. I've tried changing different combinations of settings but the text won't appear horizontal.
The two blocks I mentioned above are inserted into one file with a number of other blocks. When I check the properties of the non-dynamic block, the "match orientation" is set to YES. I cannot, however, change the "match to orientation" setting to YES on the dynamic block. Is this simply because it is a dynamic block or am I missing something? I don't create a lot of dynamic blocks and therefore I am not a wizard at it so I am assuming I am doing something wrong.
1. What is the easiest way to find points that are not constrained? I get a notice that the block is not fully constrained and its a nightmare going through all the lines trying to find where I need to apply a constarinet.( I can't wait to get off ACAD and back to Inventor.)
2. When I try to save a dynamic block using the Save Block icon under Open/Save, if the dynamic block is not fully constrained, and I click save, when I reopen the block to edit all of my constraints are gone, this has happened twice. Now I just exit by Xing out and saving changes.
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
I need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
I need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.
I tried adding position point and link, etc....I run out options and don't know how to fix this.
I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).
I am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered
I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.
