is there a way to make a dynamic block that adapt when using with constrait...i want the block, wich will be a panel with different visibility, to adapt between 2 geometry using coincidence or colinar constraints
so when i change the parameter of the distance between the 2 geometry , the block length will ajust accordingly i'm not new to the dynamic block but to using parameters with it, never done that.
My boss gave me a copy of Autocad 2012. I've messed around with architecture 2010 before so the ribbons are no surprise. One thing I have noticed that's really different is the dynamic block constraints & block table actionblock properties table? I looks very similar to the lookup property table
View 0 Replies View RelatedThe attached image shows a block of a speed ramp. I have a linear parameter in the middle of the block to stretch the block. When I stretch the block I want the triangles to be evenly spaced. I have setup constraints as shown. They are all linked back to d6 but d6 is locked. How do I unlock it so that it changes and the dims update?
View 9 Replies View RelatedI created a block (Attached).
Is there a Geometric Constraint that can keep the two lines (red and green) keep touching the blue one and look like the drawing right below the block that is Exploded?
I am trying to create a dynamic block that represents a cable with an attribute attached. The block is essentially a line that runs along the Y axis. I have created a distance parameter with a stretch action attached. The line is to remain anchored at the top and the bottom end is permitted to stretch.
Problem: I have an attribute inserted to the left side of the line (offset at -2mm TC insertion) at a rotation angle of 270. When I select the stretch grip (in the drawing environment) I would like the attribute to remain centered with the line maintain the offset and maintaining the rotation angle. I have exhausted all of my options (limited experience).
I am in the process of fixing one of our dynamic blocks. It's a fairly simple fix where there was a typo in one of the names of our items in the lookup that needed to be fixed.
I changed the name of the item in the lookup table. I went and did the test block and it seemed to work fine, but when I bring the block into a drawing, it reverts back to the old lookup as if I did nothing at all.
I made sure that the path was correct and I even just dragged and dropped straight from Windows Explorer to no avail.Does AutoCAD keep referring to the old block? Did I forget to change something else?
my problem is whenever i make a new block a stretch point appears even if its not a dynamic block . also its not a stretch point, because when i click on it, it just move the block , and it always appear on the coordinates 0,0 it cause me a problem when I insert the block , autocad use this point as a base point , and its very far from the real block .
View 1 Replies View RelatedIs it possible to create 3D dynamic block and export dimension data ? in detail I would like to create a pipe block, use it in a dwg with different length and export data in order to know sum of all blocks with different length.
As alternative, In case 3d dynamic block is not feasible, is it possible to export data to calculate dimension of 3D object?
I want to create a dynamic block that as I select my pick point to move it over it stretches the box, however at the same time it arays 2 other lines at the same time. The trick is I need the 2 lines that array to renceter them self within the overall box thats being strtched. To put this in exact teerms I'm looking to create a dynamic block of a reinforced concrete slab that you can stretch to the length you want and at teh same time the reinforcing sysmbeol (----- X-----) will array itself and recenter. Is this possible to do?
View 9 Replies View RelatedI have created a drawing border block for my users to insert into their drawings. Within the block there are dynamic blocks which have visibilty states. However when you insert the border block with the dynamic ones you can't do anything with them? Is there anyway of making the border 'flexible' or something so that it maintains the fact that it is a block with all the attributes but you can use the embedded dynamic ones. Other than the obvious edit block in place or block editor?
View 2 Replies View Relatedwhat I need to do to fix the elevation tag block below? I want the text to rotate and be readable as I rotate the block. Right now the text rotates but it's not readable when it's on the left hand side.
View 3 Replies View RelatedI have a drawing with multiple instances of a dynamic block. I have a second drawing with said block modified.
I want the first drawing's block to be updated to the modified block without reinserting each block separately.
I don't have the block as a separate file to "insert", only available to copy. With it being dynamic, I don't trust using the block editor and just copy/paste from the modified into the original.
Is there a way to redefine the block?
Is there a trick in using a dynamic block in a table cell? When a dynamic block is inserted into a cell, any visibility can be viewed (Properties Manager) in that cell if the visibility state has a block in it. What happens if the visibility state does not have a block. That is, if the view has exploded block so one can use parts in actions etc? Can I view ANY state in a cell regardless if it has a block or not? Or must the visibility states have blocks to be able to use it in the table cell?
View 2 Replies View Relatedi'am trying to create a block that has 3 components that can change
1- crane model or base
2- crane boom has different lengths and needs to rotate at pivot point
3- crane jib has different length and offsets from the crane boom
How to do this in one block or do you need to have 3 seperate blocks and just piece together.
Is there a way to use more then one visibility parameter in a dynamic block in autocad 2013
View 1 Replies View RelatedFor my AutoCAD class we are supposed to make a dynamic block of a basic theater flat which we can then stretch into different sizes. I was able to do the vertical stretch no problem, but when it comes to the horizontal stretch, the lines do more of a move action then stretching. I have redone it several times but it still won't stretch properly.
View 1 Replies View RelatedI have made up an extensive dynamic block library over the year, however in the latest version when I have tried to modify blocks with visibility states you can not cycle through the different states it will just revert back to the first one.
View 3 Replies View RelatedI'm trying to create a Dynamic Block of an 3/4" x 3/4" aluminium angle with holes:
Depending on the length the number of holes will vary.
The distance between each holes need to be somewhere between 8" and a maximum of 12".
The holes must be centered and start from 1 1/2" up to 2" from each ends.
Each distance must be not more precise then 1/16" (no rounded off dimensions)
I'd like to simply drag the handle of the linear parameters (No lookup or visibility for 2 hole, 3 holes, 4 holes etc.)
i just upgraded to 2013 and my dynamc block functions have dissappeared. the ones that flip doors etc.
View 1 Replies View RelatedI have been building a bush cross section.I am building it as a dynamic block as I need copies in many different sizes.
Due to the cross section I am using hatches to indicate different materials (only 2)
When I change some distances linked to actions the hatch remains inside its boundary and conforms to the new shape, most of the grips work perfectly whereas one, the top left grip, misbehaves time after time and breaks the hatch associativity.
I should mention that I had it working perfectly earlier, but was asked to add a fillet onto my drawing and after putting this in and tweaking everything I have no longer been able to reach perfection.
So I'm creating a block with a block table and constraints. The constraints such as Geometric Constraints work just as assumed. When adding in dimensional constraints we start to have more fun. So I have dimensional constraints that use other dimensional constraints to manipulate itself.
EX. dimconC = (dimconB-dimconA)
dimconA is 12
dimconB is 14
dimconC would be 2
Now when ever dimconA or dimconB change dimconC would populate accordingly.
With this I wanted to make an attribute that could be placed in instead of a dimensional constant.
EX dimconC = ((Att1*dimconB)-dimconA)
Att1 is 02
dimconA is 12
dimconB is 14
dimconC would be 16
However when trying to place in formula that references a attribute I keep getting an error "A DEPENDENT EXPRESSION CANNOT BE EVALUATED" So I assumed it was missing an expression from the attribute, however once entering an expression in for it I still get the same error.
(full error message attached)Constraint_Error.JPG
Is this something that is not allowed at all or have I over looked something?
I sent the following message to autodesk:
Issue: Dynamic Block causes crash
Preface: A dynamic block c/w a "flip" parameter and a multiline attribute will crash when the block and attribute is flipped, and the attribute justificatiob modified.
Explanation: When the dynamic block is flipped, the multiline attribute is also flipped causing its justification to switch from "top left" to "top right". When the attribute is edited in the in-place attribute editor to switch the justification back to "top left", it causes AutoCAD to crash.
Workaround: Instead of using the in-place attribute editor (i.e. same as MText editor), the attribute justification is changed by modifying the attribute properties in the "Enhanced Attribute Editor" dialog box - on the "Text Options" tab
I am currently using Autocad 2014 and I am attempting to insert a dynamic block from a tool palette. I would like to click on a dynamic block in the tool palette and have it prompt for the (uniform) scale. It seems simple enough but either all the dynamic properties are lost or it is inserted at 1"x1" (the scale of my original block). How to get this to work?
View 3 Replies View Relatedthe layer order will not function as soon as the block is made dynamic. I have been creating my blocks the harder way and still have more to do, so what to do.
The last time I asked the Autodesk technician, I was told it is a program (Autodesk) issue which I call a bug. I have tried the draw order and the Textofront still, no better result.
I have searched high and low and still could not find a tutorial to really explain how to create a drawing title with attributes (Detail Number, Sheet Number, Detail Title, Detail Scale). All I find are on creating dynamic block, which I could achieve, but I need one for a block that has (or will have) attributes.
I was able to find a tutorial on attributed door numbers, but it does not work for drawing titles that has attributes. GOAL: I would like to have all my seven drawing titles in one file and to be able to stretch the leg of any selected title to a desired length.
I created a dynamic block to represent a room in a floor plan. It displays the dimensions and area of the room and can be stretched. But it's defeating the whole point of being dynamic. The area won't update unless I do a regen.
I've seen comments blaming MTEXT for the problem, so I tried putting the area field in a line of TEXT or DTEXT. It still didn't update unless I did a regen.
Infrastructure DSP '14 / Product DSP '14 / Vault Professional 2014
Dell Precision T1650
Windows 7 Professional SP1 64-bit
Intel E3-1270 V2 3.5GHz / 32G RAM
Nvidia Quadro 2000, Driver 331.82
Space Navigator, Driver Version 6.17.7
I'm trying to create a dynamic block that uses a parameter and an attribute definition to determine the diameter of a circle in that block. I plan to export GIS points with diameter in the attribute table into a CAD file with the block definition. I'm having trouble figuring out how to set up the parameters to read to attribute definition and adjust the circle diameter. Using AutoCAD 2013
View 5 Replies View RelatedI found an interesting dynamic block. It has a clipping boundary but you can drag the 'leg' out of the boundary. How can I make such block?
See attached dwg file.
I am tying to create a Dynamic Block of a steel angle of multiple sizes and thickness. I used Dynamic Blocks before and live the idea of changing sizes on the fly with out having to delete and recreate an object.. I got as far as creating an angle of different sizes, i.e.. 4x4, 5x5, etc. and different thickness but can't get the thickness to work with the radius of the angle.
View 2 Replies View RelatedI am trying to set constraints to this block and having some issues. I want to constrain the attribute text so when I stretch the block from the grips the text centers itself automatically within itself. The constraints will not let me pick the grip on the attribute text as a point.
View 2 Replies View RelatedI've only got LT2008 at the moment, but this is a pet project that if my office upgrades me I want to finish.
Is it possible to rotate a line by using the length of a separate line? But the degrees of rotation need to be worked out by the length of the line
as in the following sum
angle of rotated line = (fixed number/360) * length of linear line
Left handed and PROUD