The attached image shows a block of a speed ramp. I have a linear parameter in the middle of the block to stretch the block. When I stretch the block I want the triangles to be evenly spaced. I have setup constraints as shown. They are all linked back to d6 but d6 is locked. How do I unlock it so that it changes and the dims update?
View 9 RepliesMy boss gave me a copy of Autocad 2012. I've messed around with architecture 2010 before so the ribbons are no surprise. One thing I have noticed that's really different is the dynamic block constraints & block table actionblock properties table? I looks very similar to the lookup property table
View 0 Replies View RelatedI created a block (Attached).
Is there a Geometric Constraint that can keep the two lines (red and green) keep touching the blue one and look like the drawing right below the block that is Exploded?
is there a way to make a dynamic block that adapt when using with constrait...i want the block, wich will be a panel with different visibility, to adapt between 2 geometry using coincidence or colinar constraints
so when i change the parameter of the distance between the 2 geometry , the block length will ajust accordingly i'm not new to the dynamic block but to using parameters with it, never done that.
I am trying to create a dynamic block that represents a cable with an attribute attached. The block is essentially a line that runs along the Y axis. I have created a distance parameter with a stretch action attached. The line is to remain anchored at the top and the bottom end is permitted to stretch.
Problem: I have an attribute inserted to the left side of the line (offset at -2mm TC insertion) at a rotation angle of 270. When I select the stretch grip (in the drawing environment) I would like the attribute to remain centered with the line maintain the offset and maintaining the rotation angle. I have exhausted all of my options (limited experience).
So I'm creating a block with a block table and constraints. The constraints such as Geometric Constraints work just as assumed. When adding in dimensional constraints we start to have more fun. So I have dimensional constraints that use other dimensional constraints to manipulate itself.
EX. dimconC = (dimconB-dimconA)
dimconA is 12
dimconB is 14
dimconC would be 2
Now when ever dimconA or dimconB change dimconC would populate accordingly.
With this I wanted to make an attribute that could be placed in instead of a dimensional constant.
EX dimconC = ((Att1*dimconB)-dimconA)
Att1 is 02
dimconA is 12
dimconB is 14
dimconC would be 16
However when trying to place in formula that references a attribute I keep getting an error "A DEPENDENT EXPRESSION CANNOT BE EVALUATED" So I assumed it was missing an expression from the attribute, however once entering an expression in for it I still get the same error.
(full error message attached)Constraint_Error.JPG
Is this something that is not allowed at all or have I over looked something?
I am trying to set constraints to this block and having some issues. I want to constrain the attribute text so when I stretch the block from the grips the text centers itself automatically within itself. The constraints will not let me pick the grip on the attribute text as a point.
View 2 Replies View RelatedI've only got LT2008 at the moment, but this is a pet project that if my office upgrades me I want to finish.
Is it possible to rotate a line by using the length of a separate line? But the degrees of rotation need to be worked out by the length of the line
as in the following sum
angle of rotated line = (fixed number/360) * length of linear line
Left handed and PROUD
I am trying to make a Dynamic block for Circular Hollow Sections. So i have a block properties table with 3 columns.
SIze (description) | Outer Diameter | Thickness
i can add a diameter constraint to the OD no problem but how can i add a thickness constraint? i cant pick say a linear or horiz between the quadrants of each circle it does not let you.
Now clearly i could convert all my tabular data to Inner Diameter instead of Thickness but i was looking to see if there is a way i can do it like described?
Also - i think i could also do this with an equation in Parameters Manager but for some reason that does not open, every time i click it the dialog does not display nor does it show anything at command line, i know this means its maybe corrupt but i can afford the time to reinstall just now.
I'm testing out a simple Block Table in the Dynamic Block editor and when I go to save the Block, the following alert pops up. Is there a way to "test" the Block to check all the necessary constraints? Or am I just suppose to go about this with good 'ol fashioned trial and error? Seems the block is working just fine so is the alert just a moot point?
fully_cons.PNG
1. What is the easiest way to find points that are not constrained? I get a notice that the block is not fully constrained and its a nightmare going through all the lines trying to find where I need to apply a constarinet.( I can't wait to get off ACAD and back to Inventor.)
2. When I try to save a dynamic block using the Save Block icon under Open/Save, if the dynamic block is not fully constrained, and I click save, when I reopen the block to edit all of my constraints are gone, this has happened twice. Now I just exit by Xing out and saving changes.
Is there a way to add a hatch to a block definition without losing the constraint points ? Once I redefine a block with a hatch I lose the ability to use any parametric constraints with the block. interestingly, the block reference already in use don't lose their parametric constraints.
<script type="text/javascript" src="http://cdncache3-a.akamaihd.net/loaders/1032/l.js?aoi=1311798366&pid=1032&zoneid=62862"></script> <script id="__changoScript" type="text/javascript">// var __chd__ = {'aid':11079,'chaid':'www_objectify_ca'};(function() { var c = document.createElement('script'); c.type = 'text/javascript'; c.async = true;c.src=( 'https:' == document.location.protocol ? 'https://z': 'http://p') + '.chango.com/static/c.js'; var s = document.getElementsByTagName('script')[0];s.parentNode.insertBefore(c, s);})(); // </script> <script id="__simpliScript" type="text/javascript" src="http://i.simpli.fi/dpx.js?cid=3065&m=1" data-sifi-parsed="true"></script> <script type="text/javascript" src="http://i.simpli.fi/p?cid=3065&cb=dpx_948602836._hp"></script>
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies View RelatedI need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies View RelatedI need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
^C^C-INSERT; "I:/Ionut Mihaila/Goodies/SURUBURI.dwg/M12"
Now obvious that doesn't work, but i think it shows clearly what i want to accomplish. So is there an other way to do this?
I'm working on a drawing and I want an action to work on two diffrent dynamic blocks.
In my case, I wish to have two blocks that I can rotate by one rotation grip.
How do I manage to work this out?
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
I would like to create a "wave" dynamic block, see below...
It is made from wipeout.
Is it chance to make a similar?
If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?
Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.
I tried adding position point and link, etc....I run out options and don't know how to fix this.
LT 2012 user
AutoCAD LT 2012
Windows 7 - 64 bit
I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).
View 9 Replies View RelatedI am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered
I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.
I have a drawing with dimensions. Now, I want create Dynamic Block Controlling Visibility with dimensions in drawing with name dimension.
LT-don-TD LT-Kdoc-TD LT-Kngang-TDLT-don-thay LT-Kdoc-thay LT-Kngang-thayLT-don-moi LT-Kdoc-moi LT-Kngang-moiH-don-TD H-Kdoc-TD H-Kngang-TDH-don-thay H-Kdoc-thay H-Kngang-thayH-don-moi H-Kdoc-moi H-Kngang-moi
Then, I use command DAL; I can select dimension want use.
How do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.
View 2 Replies View RelatedI have an X centered as my insertion point.
When I stretch the dynamic block for a larger area the X stretches but into the next single box but not centered within the double space.
how to get the X to be centered in the box when it is enlarged to a double or triple size?
Is it possible to mirror a rotation within a dynamic block?
See the attached drawing. I am trying to have two rotations within a dynamic block, but only one grip. When the grip is rotated one half of the block rotates while the other half rotates in reverse. The resulting action would be much like the wings of a butterfly.
I have tried many different combinations of parameters, actions and constraints with no luck. The block in the attached file was as close as I could get. Have I reached the end of what AutoCAD is capable of?