A work mate here at sometime or another clicked on the "always perform my current choice" check box when the "Hatch - Large, Dense Hatch Patterns" dialogue box appeared.
Question is, is there anyway to reset this so the dialogue box comes back up?
Just downloaded Autocad 2013 and am missing quite a few of the standard hatches (siding, soldier, board and batten, etc.) What should I do to get them back. When I open old drawings with these hatches in them, they load just fine...but I am unable to hatch any new areas with these hatches (because they are not listed in the hatch library)
View 9 Replies View RelatedI have a line drawing from a draftsman. It was imported from some other program, but I'm not sure which. However, this has cropped up many times over the years on my drawings as well as others. It just is typically quickly remedied with a workaround.
The hatch spacing too dense issue requiring me to break up the area: this problem will occur on equally sized areas at the same zoom factor at which I just hatched an adjacent area. I have changed the "MaxHatch" variable environment from stock at 10k, to 100k, then to 1,000k; yet the problem persists. I don't have a particularly fast machine so by that point I decided there was no need to max the variable at 10,000k. There are no z variables in the drawing though it appears, almost randomly, to have plines or lines along the same length of wall.
The second issue is the closed boundary. This occurs on lines that are connected at all corners, even when I stretch and reconnect a line, though that is a very time consuming method. When I increase the hgaptol variable it will hatch bizzarre areas that have no relation to what I am attempting to hatch. This is also occuring even inside a REC that I created just prior to hatching due to error on the original layout. I have to hatch an object rather than select an internal point. It has become so obnoxious in this drawing that I decided to post with these questions.
I have been using AutoCAD Civil 3D lately but went to use my AutoCAD 2011 I noticed I have no hatch patterns. I thought that these patterns were located in the support folder so I got my DVD that has the program on it out and was going to reload AutoCAD to fix the problem. It would not reload it so I copied the support folder to my computer in the AutoCAD file and still nothing. What can I do to get my hatch patterns back?
View 7 Replies View RelatedWhere do I save custom hatch pattertns in autocad? What file? Support? Do they have to be saved one at a timeor can they be saved in a folder?
View 4 Replies View RelatedI opened a drawing that I had not opened in over a month originally created in AutCAD 2011, and now using 2012. It appears only some of the hatch patterns that I created are now duplicated, and in some cases up to 17 times! When I select the pattern it doesn't show that there are multiple hatches underneath, but when selected it shows in the properties box All(2) or more. One of my patterns was scaled down and rotated 90 degrees and because when I select it it's showing 10 entities selected I cannot scale it back or rotate it without deleting and re-hatching. The .dwg is pretty complex so doing this for every hatch that shows multiple would be very tedious.
View 4 Replies View RelatedRecently switched from AutoCAD 2006 to AutoCAD 2012, I have hatch patterns set up for different area, with scale, layer, etc., when inserted using the Tool Palette. Never had an issue with it, but in 2012 it doesn't seem to work. Instead of inserting the hatch with the layer specified in the tool palette, it assigns the hatch pattern whatever layer was used when hatching a previous area, using the hatch dialog box.
View 3 Replies View RelatedI have added my custom hatch patterns to the .pat file and they aren't showing up. Is there a certain step I am missing in order for this to work? Is there an easier way to load my custom hatches in CAD 2010 that I am not aware of?
View 2 Replies View Relatedrecently installed Acad R2010 and I need to install new custom hatches but don't know how.... I got working with Autocad since 1990; probably it was R2.0. This is the first time that I try to do it, so I don´t want to mess the whole thing misplacing my .pat files.
View 9 Replies View RelatedI just upgraded from Autocad LT to Autocad 2012 (full version). When I go to select a hatch pattern by left clicking on it the program locks up. Then I have to "force-close" Autocad 2012 and loose some of my work. It has done this in several diferent drawings. Autocad LT does not have this problem.
I have a HP Z workstation with 6 gigs of ram and an Intel I-5 processor (very fast machine) with a quadro fx 380 grahics card.
I tried reinstalling Autocad 2012 and that didn't work. Not sure what to do.
We are curently using ACAD2011.
I installed ACAD2012 but never got the Migrate custom settings box upon opening ACAD2012 for the 1st time.
I reviewed Autodesk Help that ensured me that I could also find it thru:
<start...Autodesk mech 2012Migrate custom settingsmigrate from a previous release>
Epic fail... all that showed up there was export and import autoCAD 2012 settings.
Where oh where could my migration tools box have gone? Why is it not there?
(FYI, this happened to us when we upgraded from 2010 to 2011 also but we thought we had done something wrong so we eventually just manually transferred files over. That was very time consuming and we do not want to perform that exercise again.)
I am in need of a lisp routine which will automatically pick up all hatch and solid hatch patterns within a drawing and change the colour to colour 254.
View 9 Replies View RelatedI just upgraded our office from 2010 (architecture package) to 2011 and I was very excited to use the new hatch improvements, but whenever I try to use the hatch command I don't get the contextual tab. I tried playing around with HPDLGMODE, and I can get the old style dialog box, but I was really looking forward to having all that on the ribbon. I looked in the CUI and I found the hatch creation one, and it's empty. I also noticed that many other contextual tabs are empty. I think maybe it's because of some setting I had it import from my previous release maybe?
We have multiple seats where I work (I'm in charge of everything computer related) and mine is the only one where this happens. Everyone one else that I set up has the contextual tab.
Should I just reinstall it without pulling in my settings and re-build my ribbon the way I had it?
I was adding hatch patterns to AutoCAD LT 2012 and have lost the hatch patterns that come on it (ANSI, ISO) is there anyway to get these back.
View 1 Replies View RelatedI am using AutoCAD 2014 trial version. There are no hatch patterns included that I know of. Is there any way to experiment with genuine hatch patterns, cross, brick, stone, etc.
View 9 Replies View Relatedim using autocad lt 2012 i got this autocad lt message says that no standard patterns available.
View 1 Replies View RelatedI have two, seemingly identical, installations of AutoCAD LT 2012 on two machines in our office. Both machines have the MEASUREMENT variable set to 1.
The acadltiso.pat file of both machines has been customized with the addition of two hatch patterns and both of these work just fine.
In addition, the support folders of both installation also have identical sets of custom hatch patterns. On one of these machines thumbnails for these are visible and all works entirely as expected. However, on the other machine, none of these custom hatch patterns appear at all. In fact I cannot even see the custom hatch pattern tab!
I would like to import some new hatch patterns, that I have downloaded, into AutoCAD 2008. Where those hatch patterns need to go?
View 2 Replies View RelatedWhere do you go to create new hatch patterns .
View 1 Replies View Relatedcreated any custom hatch patterns for Inventor , If so, how?
View 3 Replies View RelatedOur engineering department users are facing this problem that the hatch patterns are not visible. Everytime they have to use the FILL command when they open any drawing. They are facing this problem with some dwgs, when anybody else opens the same drawing this happens again. After that they are unable to see the hatch patterns in any drawing. After using FILL it becomes visible but restrting the AutoCAD reverts the setting back so they unable to see the hatch pattern again. After opening that dwg in all files they are unable to hatch.
View 3 Replies View RelatedI have new hatchs(extension PAT) patterns and want to put the in my autocad architecture 2010, I can't find where to paste them.
View 1 Replies View RelatedI am trying to load hatch files from StoneCAD. In the past I have been able to take hatch patterns from various sources and locate them in a file within AutoCAD LT, then use them without issue.
I have never touched a .pat file or written anything in notepad or word, just simply copied the .dxf files to a file on my computer and was able to use them through AutoCAD LT 2009. Recently I had to reload the software and I can't figure out where I would go to put these hatch files.
How do you install new hatch patterns in LT2006. Where are the pat files?
View 8 Replies View RelatedIs there a way to bring hatch patterns from AutoCAD Architecture into AutoCAD?
View 3 Replies View RelatedI downloaded new hatch patterns and I don't know to which folder I am supposed to install them. I have AutoCAD LT 2013.
View 5 Replies View RelatedI've not done custom hatch patterns in the past, but I'd like to create a custom hatch pattern using a block I have. Is there an easy way to do this?
Would like to make a 8" CMU (section) hatch pattern, as an example, to use in automated sections that I generate.
Pretty easy to see where I'm headed w/ this.
Any easy conversion tool or the ability to explode the block, select everything for a hatch pattern and click "OK".
Likely there isn't, but it never hurts to ask when starting out.
I am using AutoCAD Architecture 2012 and I would like to add a hatch file but all the hatch files are located in the following file C:Program filesAutodeskAutoCAD Architecture 2012ContentPackscp_ADT_UKsupport. Adding a hatch file?
View 2 Replies View RelatedI need to select various shading patterns in a section view drawing and assign all the same settings using VBasic but can not find the way to go. For example, all a 45 degree angle and scale to 0.25.
View 3 Replies View RelatedInventor 2010 Style and Standard Editor includes 35 CUST## hatches. My guess is, it stands for custom. Is there a way to import hatch patterns from AutoCAD PAT file? This functionality is available for line types through importing AutoCAD LIN file.
Xeon CPU 3.6GHz
Nvidia Quadro FX 3400
Driver version 6.14.11.8246
Win XP Pro (32) SP3
4GB RAM w/o 3GB switch
AIS 2010 SP1
I want to show Cut & Fill volume in Different Hatch patterns (Excluding Solid Hatch).
View 3 Replies View Related