I have a dynamic block that I found on a website [URL]...... I have inserted an image and a Z coord. The problem is when I move the block with the grip the image doesn't move. I have redone the selection sets but no joy.
AUTOCRDS.dwg
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block
I made a dynamic block with attributes. The block was to be moved using Linear parameter + move action, and then a lookup parameter and action.
The block moves as it is suppose to but the attributes are left behind. How can I get the attributes to move with the dynamic block?
The attribute properties are:
Verify = Yes.
Lock position: Yes or No don't seem to make a difference.
Is this a bug in AutoCAD or is there a solution to this?
I have a problem with using .Net to insert a dynamic block and set the size property. The attribute text does not move correctly on insert, but will if manually stretched after the fact. From my research the recommendation is to make sure the attribute definition is marked as "Locked".
I have an attribute definition inside a circle (classic door/window number), both the circle and attribute are included in the Action Selection Set, however only the circle moves correctly. It all works correctly if manually inserted/stretched.
In "test" mode, this block works well except for the point of the arrow. If you stretch the line under the title, then move the arrow point to somewhere else, then flip it, the arrow point and its associated grip needs to stay put.
It actually does, the first time. BUT then if you move the arrow point again and flip it again, it does not.
Then, when I inserted it into another drawing, either with "insert" or via SSM, the flip doesn't stick to the point even the first time.
So I guess my question is how to flip it but keep the point where it happens to be when the flip occurs. Like a multileader, because what I am actually trying to create here is a multileader that has an annotative block with attribute fields, to be used with SSM.
I need this block to do the following:
1. Move the right piece so it ends at 3', 4', & 5'.
2. the move right hook and 'backing' to stretch/copy (or array) so it adds a hook to the right and fills in the backing.
so this means that a 3' gets 4 hooks, 4' gets 5 hooks and 5' gets 6 hooks.
3. the block as shown is the smallest configuration with 3 hooks.
I could just set up a visibility and draw each one at it's appropriate length but I'm trying to keep this simple block to a min size. If all else fails, that's the route I'll take.
I've tried a couple different configurations and I keep getting duplicates or the end piece doesn't move the correct distance.
I have this Dynamic Block which has a few distance parameters on it and an attribute at beginning of each parameter which are attached to a stretch action. If manually bring the block in. And set a value to attribute and then stretch the it , attribute move along with action. But when I do it pragmatically it doesn't . Basically attribute stays at original location of original block before stretch. What is wrong with my code. Or Shall I do something to Attributes when I change the distance parameters in Program? I don't know .
I have a function which bring the block in and set attribute first and then another call which change the distance . So I don't show the first function which to me works fine . The problem is this part.
For Each myBRP As DynamicBlockReferenceProperty In myBRC
For I = 1 To NumbderOfDistanceParamsinDynBlk
If myBRP.PropertyName = "Distance" & Trim(i.ToString) Then
myBRP.Value = DynDistancevalue(i)
End If
Next
Next
I made a simple block for a utility pole in plan view. It consisted of a donut with one string of mtext beside it. I had created it so that the text would orientate itself to be horizontal in each viewport regardless of the ucs angle. I later added a line for a guy wire and made the block dynamic with visibility states. Now I am unable to have the text orientate to a horizontal position in the viewports.
View 8 Replies View RelatedWhen I move my mouse over my image the brush cursor is not moving and it will not let me click on my image (with the mouse) the crosshair/cursor will follow it, however the brush will not, nor will any other tools, my wacom tablet however works fine.
I thought it must be something to do with GIMP accepting input but its not going as of yet.
I don't know why but I don't see images of my dynamic blocks at tool palette.
View 6 Replies View RelatedThis process works fine on my desktop but when I try to move an image from LR4.4 to CS6 on my new Lenovo laptop (Windows 7) nothing opens and I freeze up.
View 5 Replies View Related1. What is the easiest way to find points that are not constrained? I get a notice that the block is not fully constrained and its a nightmare going through all the lines trying to find where I need to apply a constarinet.( I can't wait to get off ACAD and back to Inventor.)
2. When I try to save a dynamic block using the Save Block icon under Open/Save, if the dynamic block is not fully constrained, and I click save, when I reopen the block to edit all of my constraints are gone, this has happened twice. Now I just exit by Xing out and saving changes.
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
View 3 Replies View RelatedI need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
View 1 Replies View RelatedI need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
^C^C-INSERT; "I:/Ionut Mihaila/Goodies/SURUBURI.dwg/M12"
Now obvious that doesn't work, but i think it shows clearly what i want to accomplish. So is there an other way to do this?
I'm working on a drawing and I want an action to work on two diffrent dynamic blocks.
In my case, I wish to have two blocks that I can rotate by one rotation grip.
How do I manage to work this out?
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
I would like to create a "wave" dynamic block, see below...
It is made from wipeout.
Is it chance to make a similar?
If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?
Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.
I tried adding position point and link, etc....I run out options and don't know how to fix this.
LT 2012 user
AutoCAD LT 2012
Windows 7 - 64 bit
I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).
View 9 Replies View RelatedI am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered
I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.
I have a drawing with dimensions. Now, I want create Dynamic Block Controlling Visibility with dimensions in drawing with name dimension.
LT-don-TD LT-Kdoc-TD LT-Kngang-TDLT-don-thay LT-Kdoc-thay LT-Kngang-thayLT-don-moi LT-Kdoc-moi LT-Kngang-moiH-don-TD H-Kdoc-TD H-Kngang-TDH-don-thay H-Kdoc-thay H-Kngang-thayH-don-moi H-Kdoc-moi H-Kngang-moi
Then, I use command DAL; I can select dimension want use.
How do I stretch a hatch in dynamic block? It does not seem to work if I select the hatch along with other lines of a counter block.
View 2 Replies View RelatedI have an X centered as my insertion point.
When I stretch the dynamic block for a larger area the X stretches but into the next single box but not centered within the double space.
how to get the X to be centered in the box when it is enlarged to a double or triple size?
Is it possible to mirror a rotation within a dynamic block?
See the attached drawing. I am trying to have two rotations within a dynamic block, but only one grip. When the grip is rotated one half of the block rotates while the other half rotates in reverse. The resulting action would be much like the wings of a butterfly.
I have tried many different combinations of parameters, actions and constraints with no luck. The block in the attached file was as close as I could get. Have I reached the end of what AutoCAD is capable of?
I have a block of a roof screen. What i want to do is to stretch it & have the slats on the front & also the supports on the rear array @ different intervals. The slats on the front would array every 6-1/2" (The slats are 5-1/2" wide with a 1" gap). The supports array every 4'-0". I have tried to do this multiple ways with mixed results. How to get my desired outcome. I am enclosing my block.
View 5 Replies View Related