I want to make a simple dynamic block showing a plan section of a window with one mullion between the window jambs. I've succeded making the block stretchable to any given length that is required.
The problem is, that I can't figure out how to keep the mullion right in the middle between the jambs.
Is there any simple way to get there using the actions and parameters in the block authoring palettes?
I am trying to make a block that I can stretch. The end pieces (gusset block) never change size. The only piece that needs to stretch is bar that connects them. The gussets are always on a 45 degrees. If I stretch it over 5 inches on the X axis, it should move -5 on the Y axis.
View 4 Replies View RelatedI've made a simple dynamic block, a rectangle with a hatch and added a linear stretch to it. The stretch works fine on the rectangle itself, but the hatch only gets moved.
I've attached an image and a drawing containing the block.
I use autocad 2011 LT and I have some problem with polar stretching!I have to get from A(see picture) to B but C is always happening! I want to put in an angle in te propertieswindow so that I become B. the angle is variable but the middle stays the same length!
View 4 Replies View RelatedFor my AutoCAD class we are supposed to make a dynamic block of a basic theater flat which we can then stretch into different sizes. I was able to do the vertical stretch no problem, but when it comes to the horizontal stretch, the lines do more of a move action then stretching. I have redone it several times but it still won't stretch properly.
View 1 Replies View RelatedI have a profile drawing of a pv module that is a dynamic block. The dynamic block has options to let you select different attachment points. The location of the attachment points and where they attach to the pv module (the rectangle) is a manufacture requirement to maintain the warranty.
I am trying to modify this dynamic block so that I can stretch both the length and the height of the module. The height was the easy part and is working in the attached dwg.
As the length changes the location of the attachment points need to change as well but proportionally to the length. Basically scaling the rectangle but only on one axis.
I have seen references to how when you insert the block you can change the scale factor or once the block has been inserted into the drawing you can set the scale for one axis in the properties menu but is there anyway to do this dynamically?
The pv modules (the rectangle) come in a variety of specific sizes so scaling the block upon insert wouldn't really work anyway.
I'm trying to create a dynamic block for plywood. I have the stretch parameter working so that I can stretch the plywood to the needed length. I also have set a rotation parameter based on the various roof pitches that we use. The problem is I would like to be able to rotate the sheathing to a 45 degree angle and then stretch along the 45 degree angle. Once I rotate the sheathing the stretch does not follow the rotation angle. I have attached the file.
View 9 Replies View RelatedWhy the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.
I tried adding position point and link, etc....I run out options and don't know how to fix this.
LT 2012 user
AutoCAD LT 2012
Windows 7 - 64 bit
I have noticed in some dynamic blocks that have wipeouts in them, that they dor not stretch with dynamic actions.
In fact, they don't seem to be capable of stretching.
I have read some post about "Autodesk Sketchbook Designer for Autocad 2012" causing some conflicts.
Is there an advantage to having it installed?Do I need to uninstall it? or not?
Does it interfere with anything else in Dynamic Blocks or the drawing file?
AutoCAD 2012 / Inventor 2012
I'm currently creating blocks for our office library. One of these is a grille with some apposed blade dampers on it. I'm trying to set up an array that will duplicate the apposed blades as I change the length of the grille. However, it will only copy the blades in pairs, not singlely one after the other. Ie, the blades are 100mm apart, and in a / pattern meaning that each instance of / or 'should' duplicate every 200mm. Except when I lengthen the block by 200mm it won't duplicate untill I've gone double the distance (400) when it gives me both / and .
View 2 Replies View RelatedI have two "drawing title" lines in my block when I use the, stretch, move, scale parameter the attributes lose the position (the drawing titles lines are stacked) and will not scale with the rest of the objects. I tried all tricks that I could possibly think of but no success.
maybe LT2012 has a bug that does not allow me do this correctly?
LT 2012 User
Windows 7 professional
I have tried to make a dynamic block using annotative objects, text leaders, etc. The block was created initially as annotative but later somehow after going over it in the block editor. It has lost it's annotative properties. Is there a way to make a dynamic block that is not annotative, make it annotative. this block has only visibility features.
View 5 Replies View RelatedAfter all this time is there a way to assign layers to different objects with a block? Perhaps using Visibility states or Lookups?
As an example:
I have a dynamic block with a door swing and text. As I increase the size of the door the text changes to reflect door size. The objects are all on the 0 Layer. When I insert the block I can assign a 'Text A' Layer to the text and a 'Door A' layer to the door. So when I switch layer states around I will either see the door, the text or both. Then I move to the second floor which has been stacked on the first floor. I insert my DB and assign layers 'Text B' and 'Door B' respectively to the text and door.
Finally when I go to my layer states I either select 'First Floor' or 'Second Floor' and the respective blocks appear depending on the layer state.
I believe there is a way to create a block of displayed objects that are shown within viewport. I know I have done this before with basic Autocad. The closest thing at the moment that I can think of is "SOLPROF" but that only works for 3D objects.
The way I remember the command working was you started off with the command, select the objects with the viewport/or maybe it was just the viewport, the command made an instantaneous block of the objects that were only within the display area.
It's possible to create a dynamic block programatically? I want to create a command that captures different selection sets of drawing objects and assign them to different Visibility States of a new block deffinition, on run time.
View 2 Replies View Relatedhow to control the draw order of objects created within an array in a dynamic block?
I have a wipeout, which works fine on the array source, but when the array produces babies, it places them infront of everything (which is only logical), making the wipeout useless.
Can I set array babies to have the same draw order as their parent?
(AutoCADLT 2013)
I have a 4' light fixture that is a rectangle. Right now I have it set up to where I can stretch it and it copies it’s self whatever length that I stretch it in increments of 4'.
Is there a way for me to modify this so that when I stretch it along an arc, that it copies its self and rotates its self along the edge of the arc?
Is there a way to make a dynamic block where I will insert the total length of this “ panel”. Say 3720mm, and that it will divide the “panel” into equal segments with a maximum segment width of 1240mm. ( so with 3720mm that would make 3x 1240mm segments)
Say it would be a “panel” of 5500mm it would be 5 segments of 1100mm, and a “panel” of lets say 3750mm would make 4 segments of 937,5mm.
I made a drawing to illustrate what I mean, A dynamic block for this will save a lot of time!
(here is the example)
How do you insert title block, so your design is in the middle of block?
View 9 Replies View RelatedI can create a block where you stretch a line and the opposite side stretches equally in an opposite direction but I can't find anything with stretching equally in the same direction.
The block in questions is a door with windows to the side. The door size will remain fixed but as I stretch the window jamb I would like the two mullions to stretch to create an equal stretch.
I have been trying (albeit unsuccessfully) to draw a DB that requires a hole spacing of 16" maximum. The problem with this is that a pair of holes will need to be added or subtracted based on the width while not exceeding this 16" maximum dimension, but maintaining even spacing. I.E., when this block is stretched down, a pair of holes needs to be subtracted and the remaining holes need to be spaced evenly. I have attached the block drawn at it's maximum width and most required holes at this width with stretch parameters for each hole set. The best idea I could think of would be visibility states for each series of holes that would be activated when the block is stretched accordingly but just can't seem to make it work.
View 7 Replies View RelatedPlease see the attached drawing. It's for a conveyor system, and the idea is that when you insert the block, you could then select the size of the conveyor and the angle of the turn (straight sections are another block).
What is suppose to happen is, when you insert the block, you stretch the conveyor to the size desired, and the rest of the block should scale to match. Then you select the angle of "turn", and you're good to go.
I got it all to work except... when you stretch the line out, everything scales, but the line doesn't stay in place and just stretch to the left, it moves, which leaves a gap where the conveyor should be.
Why I can't get the attribute to stretch with right hand arrow.
View 2 Replies View RelatedI am working on a few dynamic blocks with ducts.The plan is when you stretch the duct to far it will automatically place a coupling and the next peace of duct.
This wasn’t the problem but if I connect more than 2 ducts it goes extremely slow. (see attached file)
I think that if I am using larger steps between stretching (still testing this theory) it will go faster but this goes against my nature of being possible to exactly decide the length on my one.
Attached is a block that I use a lot. Originally I had two separate single line text attributes for the "title". I modified it to have a single multiline text attribute instead. I want this attributes text box width to stretch along with the line below it, so that long text strings will automatically adjust to single or multiple lines as necessary and not run off the end of the line. As it stands now I have to stretch the line and then adjust the width of the text box to match.
Also it would be nice if the bulk of the text would stay on the bottom line and only the "overflow" would move up to the next line.
I'm looking at a block which has multiple visibility states, 2 of which show a beam as a side elevation, where the beam can be stretched to give a length. This works well.
But I'd like to be able to have the beam stretching so the bottom flange of the beam can stretch relative to the top to give an angle to the beam end, and also have the lines representing the flanges (whose position will vary depending on the steel size) can also be stretched to give a neat cutoff.
Stretching the bottom of the bottom flange is easy, but I can't figure out how to stretch the inner lines? They would have to be moved a proportion of the distance which will vary between beam sizes/flange thicknesses, so putting in a fixed multiplication factor won't work. The mathematics to set a multiplication factor based on other elements of the dynamic block is easy, but is it possible to have such implemented on a varying basis?
Elevation showing what I want to do, and the block itself attached.
is there a way to make dynamic blocks stretchable similar to a mleader,
the blocks i create are only stretchable by grips, and not by crossing
(i am using linear or point parameter stretches)
I have a problem with Dynamic Input suddenly displaying dimensions in the middle of a line rather than on screen as I work. What I mean is that if I draw a line the length of the line is displayed at the center of the line. When I zoom in to one end of this line the display of the length of the line is no longer displayed on screen but remains at the center of the line. I use AutoCAD 2008.
View 5 Replies View Related1. What is the easiest way to find points that are not constrained? I get a notice that the block is not fully constrained and its a nightmare going through all the lines trying to find where I need to apply a constarinet.( I can't wait to get off ACAD and back to Inventor.)
2. When I try to save a dynamic block using the Save Block icon under Open/Save, if the dynamic block is not fully constrained, and I click save, when I reopen the block to edit all of my constraints are gone, this has happened twice. Now I just exit by Xing out and saving changes.
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
See the attachement with the block