AutoCad :: Dynamic Block - Getting Set Of Parameters To Work Together
Jan 19, 2012
I'm having trouble getting a set of parameters to work together in this block i have created.
File attached for reference
Block 1 (EXTENT_OF_WORKS) and Block 2 (EXTENT_STRETCHED) are attached to file.
As is on both blocks i need a central insertion point/base point.
Block 1 has two rotate commands. The inner rotate command is to align the block so that it is perpendicular on a straight line of a route. The outer is to align perpendicularly in the case where the centre point of the block falls on an arc segment of a route.
Block 1 has also got a flip command.. to flip.
As is block 1 works well. but i also need a stretch command that can extend both ends of the block, away from the centre, at the same time. See block 2.
I have tried to complete this block in multiple ways to no avail.
I am looking for a way to use the ATTIN/ATTOUT workflow to bring in data from an excel spreadsheet to drive the size of each of my block's instances. The block will be simple, a rectangle, with width and length parameters. For each entity in my excel/csv file these parameter values are spelled out. I know how to display these parameters in my attributes, but I don't know how, if I were to feed in these values, to drive the geometry. If there's a better way to take a list of width and length values to generate a series of blocks each with a rectangle containing its respective size.
Is there a way to know what kind parameter type is using in a DynamicBlock Property ROTATIONPARAMETERENTITY, LINEARPARAMETERENTITY or POLARPARAMETERENTITY
I am trying to make a dynamic block below. I need the "end" of the line to be "moveable". I've tried the point parameter and the stretch action with no luck.
I am trying to create a dynamic block that allows me to insert a single rack into a drawing and make a single row of racking with all racks staying 9'-0" center of post to center of post. Also would like to be able to turn that one single row into a double row that spacing between rows can be modified. I have attached a cad file showing a single rack and two example, one of a row of double racks and one of a single row of racks. This rack is 48" deep i will also have to create this for a 60' deep rack so how i can create future rack sizes and rows.
I have created a pretty nice dynamic door block with flip parameters - size changes - and visibility parameters for jamb/no jamb. However I would like to add an option for changing the door from 90 degrees, 45 degrees and closed. I can't use the visibility parameter since I am using that for jamb/no jamb option. I was hoping to add a rotate parameter, but am having issue with the arc line. Is there a way to have the arc move with the swing in the door? If so, I can add that to the more refined door block. I have attached Drawing 2 (Door with just the rotate parameter) and Drawing3 (More refined door dynamic block without the swing option).
I have a new project coming up where I need to write some simple programs to access the dynamic action parameters in some existing dynamic blocks.I have viewed what I could find on AU, but I still ave not found anything relating in-depth to dynamic blocks.
Any good Tutorials, Articles, or White Papers, on working with dynamic blocks with autolisp/ vlisp? The main function is to access a parameter and change it by entering a numeric value, updating the block. say from a linear/polar stretch, or a linear/ polar move.
Is it just me or do the actions associated with parameters disappear on occasion from the block editor? Sometimes a regen will make them reappear, other times not. Closing/opening the block editor is one way to make them visible again (worked a few times at least).
I'm trying to create a window block with a grille. I've created the block and the horizontal grilles. What I'm having a hard time with is creating the vertical grilles. I would like to set up an array that would take the glass width, divide by 12, round up the value to get the number of vertical sections. Here's the code that I've figured out:
the layer order will not function as soon as the block is made dynamic. I have been creating my blocks the harder way and still have more to do, so what to do.
The last time I asked the Autodesk technician, I was told it is a program (Autodesk) issue which I call a bug. I have tried the draw order and the Textofront still, no better result.
I am having difficulty figuring out how to get my detail callout block to work properly. What I would like the block to do is scale/stretch the circle so a larger area can be detailed. Linked to this function I would like the attributed tag with line to stay on the outside of the circle once it's adjusted.
Another function I can't figure out is rotating the the text/line so it can be located anywhere around the circle. I currently have a vertical and horizontal flip but the attributed text doesn't remain on top of the line. So, I guess there are 2 things I can't get to work in that one.
I have problem with attached block (also with other similar blocks with field). This block include field in block attribute. Works fine if I copy and paste this block. When I drag and drop from Tool Pallete field disappeary.
I'm working on a dynamic door, that has specific parameters to change its size and orientation. Everything works pretty good, only the arc for the door won't react the way I want it.
I've made annotative blocks and I've made dynamic blocks... My intent is to integrate both but I can't find a way to move dynamic block parameters separately at different annotative scales.
In other words, if I insert an annotative dimension and add multiple scales I can move the dimension grips independently at each scale. If I insert a dynamic block I want to be able to use the dynamic block's action "grips" to do the same. However, with a dynamic block, if I move a stretch action at one annotation scale it moves the action at all annotation scales.
1. What is the easiest way to find points that are not constrained? I get a notice that the block is not fully constrained and its a nightmare going through all the lines trying to find where I need to apply a constarinet.( I can't wait to get off ACAD and back to Inventor.)
2. When I try to save a dynamic block using the Save Block icon under Open/Save, if the dynamic block is not fully constrained, and I click save, when I reopen the block to edit all of my constraints are gone, this has happened twice. Now I just exit by Xing out and saving changes.
So I've done a reasonable amount of work with dynamic blocks. I have a block with a rotation action and grip to arbitrarily align it. However I realized when trying to combine it with an alignment grip (which actions on the basic or fundamental block rotation angle) that there didn't seem to be a way to some how link a dynamic block rotation action or one of the custom angle properties to a the fundamental block rotation angle. Thus there are two additive rotations at work; the dynamic block one with its grip and the fundamental rotation property.
This can cause some confusion when one person aligns with the grip and another via rotating the block's fundamental property and would also be problematic in the generalized sense if one was trying to select or programmatically read back the net angle alignment.
I have a dynamic block, that represents a stirrup.
I inserted in the block a Block Propreties Table, that have some preset dimensions for the stirrups. The grip of this table I decided to put in the top right corner.
The problem is that I can't make this grip moveable )
new to dynamic blocks but looking to streamline my wiring diagrams here and have created a block that shows the typical wire styles we use in a simple easy way. I now want to add an overall flip to the entire block and have not been able to find set this. I would prefer to use the same label and go from there. I have included the block to show what I mean. It is only working on the single visible item at the one time. I know this has to be possible just let me know what I am doing wrong. I am running AutoCad LT 2013
I need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I wish to create a dynamic block containing some attributes. These attributes are inside rectangles that can't be modified in length using linear parameters ; but the attribute has to be always in the middle of the rectangle. So, I draw a line inside the rectangle (in a hidden layer) and insert the attribute with center justification (not sure for the translation) that I place in the middle of this line ; then I put a coincidence constraint (not sure for the translation, but it's the first one) linking the middle of the line with the middle of the attribute.
But here's the problem : when stretching my rectangle, the insertion point of the attribute suddenly changes from "center" to "bottom left".
I need to do some repetitive task on a lot of dynamic blocks, unfortunately, when I open each file, AutoCAD keeps asking if I want to open it with the block editor.
Is there a way to disable that dialog and open the files as normal dwgs?
A hint: BLOCKEDITLOCK doesn't make it, it shows another dialog...
I'm trying to make a dynamic block of a column radiator.
It should be very simple. It's a 46mm wide module that comes in a range of heights (300, 500, 600, & 750mm) and a range of assembly widths (9, 13, 18, 22 & 27 modules wide - more commonly given as mm widths of 414, 598, 828, 1012 & 1242 respectively).
My attempt at constructing it has gone quite well, but when 'stretching' the block a ghost of the core 414 (w) x 300 (h) unit remains. I attach the block to give you a better idea of what I mean.
I have a drawing ("SURUBURI.dwg") with several dynamic blocks ("M12", "M16", "M18" ... an so on...). I want to insert in my current drawing, one of the blocks from SURUBURI.dwg, for instance the block named "M12".
For that i tried creating a new command "INSERT_M12" that has the following script :
I have successfully created a dynamic block. I can insert it into AutoCAD, and it behaves like I want, except for one thing.
I can select the block and change it by taking a grippoint and place it at another position. So my block is e.q. stretched, just like I wanted.
But then. When I want to use the ordinary STRETCH command of AutoCAD, I can only stretch the insertion point of the block, but not the grippoints. Is there a way to set a grippoint to be select edable by commands like STRETCH.
Why the drawing title in my dynamic block will not scale up or down. The rest of the objects scale properly but just this the drawing title text attribute will not follow suit.
I tried adding position point and link, etc....I run out options and don't know how to fix this.
I have a dynamic block with several actions and parameters. There are three grip points. Two are visible. One appears when you move one of the other grips. If i insert or paste this block near my template, the X/Y basepoint stays near the template when i drag the block on the template with one of the other two grips.. When i print the drawing the basepoint stays visible and the scale on my printed drawing is not correct (smaller).
I am creating a dynamic block of a conveyor belt it has a set number of widths and needs to be stretchable in length, which I have managed to do. The motor is placed half way down the length of the conveyor and needs to stay centered
I know I need to use the move command and put in a factor of 0.5 somewhere, but I can't remember how to do it.
