I would like to create a "wave" dynamic block, see below...
It is made from wipeout.
Is it chance to make a similar?
If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?
T11.jpg
I would like to create a "wave" dynamic block, see below...
It is made from wipeout.
Is it chance to make a similar?
If I make a list for the length (from 125 to 350), after can I make a table /list /summary where these size are shown?
I need to create a dynamic block for a "Glass Panel" in a balustrade. I need to be able to insert it, in one corner and stretch it in another corner, to suit the staircase angle.
I've created the block, but it isn't working correctly. I've attached a drawing, with the left hand drawing a sketch of how it needs to be. The right hand drawing is my dynamic block attempt. As can be seen, when the block is stretched between the 2 points, it doesn't follow the angle of the staircase correctly (Very slight run off)
I have a drawing with dimensions. Now, I want create Dynamic Block Controlling Visibility with dimensions in drawing with name dimension.
LT-don-TD LT-Kdoc-TD LT-Kngang-TDLT-don-thay LT-Kdoc-thay LT-Kngang-thayLT-don-moi LT-Kdoc-moi LT-Kngang-moiH-don-TD H-Kdoc-TD H-Kngang-TDH-don-thay H-Kdoc-thay H-Kngang-thayH-don-moi H-Kdoc-moi H-Kngang-moi
Then, I use command DAL; I can select dimension want use.
I am looking to create a dynamic block that changes in scale, ex. If I have two (2) viewports in paper space, one 1/4"=1'-0" the other 1/8"=1'-0" I want my blocks to appear to be the same size in paper space.
Also, I would like my blocks to change attributes/features ex. If I have a "light switch block" I would like to have the option of switching the block from a 3-way switch, 4-way switch etc.
I would like to create an "Y" dynamic block, see bellow.
The hole length and the "cross" point will be variable, between the two sticks will be 90 deg, and it will be FIX.
I would like if I change the "variable 2" distance the two sticks follow the cross point, and the top of the sticks stay in the same level, but between the sticks the 90 deg stay!
I would like to create an "Y" dynamic block, see bellow.
The hole length and the "cross" point will be variable, between the two sticks will be 90 deg, and it will be FIX.
I would like if I change the "variable 2" distance the two sticks follow the cross point, and the top of the sticks stay in the same level, but between the sticks the 90 deg stay!
Is it possible to create 3D dynamic block and export dimension data ? in detail I would like to create a pipe block, use it in a dwg with different length and export data in order to know sum of all blocks with different length.
As alternative, In case 3d dynamic block is not feasible, is it possible to export data to calculate dimension of 3D object?
I want to create a dynamic block that as I select my pick point to move it over it stretches the box, however at the same time it arays 2 other lines at the same time. The trick is I need the 2 lines that array to renceter them self within the overall box thats being strtched. To put this in exact teerms I'm looking to create a dynamic block of a reinforced concrete slab that you can stretch to the length you want and at teh same time the reinforcing sysmbeol (----- X-----) will array itself and recenter. Is this possible to do?
View 9 Replies View RelatedI am trying to create a dynamic block library but can't quite seem to get it right.
The only dynamic feature I need to use right now is visibility states so i'm sure it's something simple that i'm just not seeing, but I thought I would ask everyone's opinion on the best way to do it.
What I am trying to do is set up a full common library on our network that our whole team uses. At the moment we all have our own block library which can sometimes cause problems. The file location / folder set up etc is sorted out but it's the actual blocks which are making life hard for me as until now we haven't really used dynamic blocks.
The only way i've been able to get the blocks where I want them so far ends up in a 'double block' meaning the block itself becomes a block again once I write it to the desired folder. This works but is not ideal as I can't get the vis state drop down menu by clicking on the block and have to edit the parent block to change the vis state.
Basically I have no problem creating the exact dynamic block I need, and no problem with a location to store them, it's more storing them that's giving me a headache.
how to work with anno text and dims, but I need to create an annotative, dynamic block.
View 9 Replies View RelatedI am trying to make a dynamic block below. I need the "end" of the line to be "moveable". I've tried the point parameter and the stretch action with no luck.
View 9 Replies View RelatedI want to create a dynamic block from existing geometry using C#.
View 1 Replies View RelatedWe have some dnyamic block share set of parameters, if we change a parameter's value, all block that reference this parameter should be change.we can do it by program.
but create user parameters for a dynamic block must be by hand, can we create a user parameter by code? another way is user global parameter. does AutoCAD Parametric function's user value can be share with dynamic block?
I have to create a dynamic block for our overhead cupboards. I've tried to do it myself but the solution is not forth coming and the brain is starting to hurt. I've attached a drawing to better illustrate what i want to do. It has the old style doors but i will create a new DB for the new style.
The OHC will be inserted with the top left point. I then want to stretch the top right point to the appropriate length and have the 3 doors stretch equally. The gap between the doors will be 22mm and must not change. The end gaps will vary because of door size but will stay within 31.2 mm to 32.7 mm (As close to 32mm as possible). Also the rh edge of the water level gauges need to be 58mm from the rh door edge.
I would like to add a new (user) parameter to a dynamic block within my code. I have noticed that this is possible manually. But couldn't find how to do this in .Net. When this parameter has been created it would be necessary to fill in a value. So the parameter can either be a general parameter, that can be adjusted later or a (user/dynamic) parameter specific for the block.
View 1 Replies View RelatedI'm trying to create a dynamic block with several different visibility states and for each visibility state I have created an attribute. Each attribute has a different text style because I need the size of the text to change when I change the visibility state. But on the model space I can only see and edit te attribute in one of the visibility states. How to create a block that allows me to see different attributes in different visibility states or that alows me to change the text stryle of the attribute acording to the visibility state?
View 2 Replies View RelatedHow to create a switch plate dynamic block. I can draw the light switch inside block editor no problem. My Objective: To insert a single light switch plate block into a drawing and have the ability to stretch the block to increase the number of switches from 1 to as many as 10 in a gang style. The light switch box would do a basic stretch, but I just can't figure out how to increase the number of switches as the block increases in width.
View 2 Replies View RelatedI cannot figure out how to create a flexible T-shaped dynamic block. It falls apart scattering the linework all over the screen. My constrain parameters for width, height and thickness are not controlling the lines. I have an I-beam shape that works, but using that to make a Tee didn't work. Or a link as to creating semi-complex dynamic blocks.
View 6 Replies View RelatedHow to create dynamic block with array action in both X and Y direction? And I have some conditions there like number in horizontal and number in vertical directions, but on exact distance (like 5 elements on 20 cm).
View 1 Replies View RelatedI have a block of a circle and a line coming from the left and right side quadrant of the circle to a common point (see pic). I want to create a dynamic block using a Stretch and Rotate parameter. You select the block, the Rotate point (grip) shows at the end of the two lines. I can grab that grip and rotate both lines and circle by moving this point around the screen, but cannot Stretch this point to a new location at the same time. How can I have the Rotation end point follow the Stretch parameter?
View 2 Replies View RelatedI run Autocad 2010LT at work, where I do fire alarm drawings. I've been trying to create a dynamic block (sort of a one stop-shop) for my wiring diagrams, and wanted to include device text with it.
My question is, is there a way I can create a dynamic block with multiple visibility states where each state has it's own independent/editable attribute definition?
Basically what I'm trying to acheive is the ability to make a different description layout for each one of my device types. (They all have a different function, and a different address style) Really so I can minimize the time I spend editing the formats when I'm trying to crank out a plan review ASAP.
I try to create dynamic block of Tectus hinges. Bassicaly I would like create multiple visibility block:
first grip - type of hinge (TE240, TE 340....)
second grib - type of view: elevation, side and plan.
For plan view I would like create third grip with options: close, open 90 deg, open 180 deg.
In attached file I'm started working on this. For now I focus on first two type of hinges TS240 and TS340. I'm close to realize my gola but still something doesn't work correct. If you play with grips sometimes block disappear on show as custom view.
I have searched high and low and still could not find a tutorial to really explain how to create a drawing title with attributes (Detail Number, Sheet Number, Detail Title, Detail Scale). All I find are on creating dynamic block, which I could achieve, but I need one for a block that has (or will have) attributes.
I was able to find a tutorial on attributed door numbers, but it does not work for drawing titles that has attributes. GOAL: I would like to have all my seven drawing titles in one file and to be able to stretch the leg of any selected title to a desired length.
I believe there is a way to create a block of displayed objects that are shown within viewport. I know I have done this before with basic Autocad. The closest thing at the moment that I can think of is "SOLPROF" but that only works for 3D objects.
The way I remember the command working was you started off with the command, select the objects with the viewport/or maybe it was just the viewport, the command made an instantaneous block of the objects that were only within the display area.
I've spent the last week and a half creating blocks that have between 2 and 10 visibility states in order to represent the separate iterations of common valves.
I would like to construct a lsp and dcl (we work off of a network drive that would enable a stable location for an accompanying dcl file along with the base lsp, though I believe that in order to do what I'm wanting done some on-the-fly dcl manipulation may be necessary) that would display the current drawings in our dynamic block folder and upon selection within the first List_box, would display the different options for visibility states for the block in the 2nd list_box. After a user selects one of the visibility iterations that are now displayed in the 2nd list, an image preview (or slide, I can handle creating the different slides for each block once if required) of how the block will be displayed in the selected visibility state would be shown in what would be the 3rd space, this time an image preview and not a list_box, though I would like proportionality between the list_boxs and the image preview. Some white space is allowable in the list_boxes.
I'm not even sure if this would be possible, but I'm assuming you can access the different visibility states in the same manner that you could access polyline verticies or block definition attributes.
I am trying to create a block that polar arrays the street lamp, but every time i try i just move the grip for it, is there something i am missing?
View 8 Replies View RelatedI'm working with Autocad 2011. My objective is to create a dynamic block made up of a circle with a letter or number inside. Here's the tricky part. As I add additional letters or numbers the circle increases in diameter automatically to fully encircle whatever it is I type. The more letters or numbers the larger the circle and the fewer the letters or numbers the smaller the circle?
Or is there a lisp routine for this type of request?
I have a ventilation attenuator I would like to compile into a dynamic block.
At the moment I have the files in folder (Folder name is length) I wish to create a dynamic block per length.
Is there and easy way to compile this without having to copy and paste from the other files?
I am tying to create a Dynamic Block of a steel angle of multiple sizes and thickness. I used Dynamic Blocks before and live the idea of changing sizes on the fly with out having to delete and recreate an object.. I got as far as creating an angle of different sizes, i.e.. 4x4, 5x5, etc. and different thickness but can't get the thickness to work with the radius of the angle.
View 2 Replies View Related1. What is the easiest way to find points that are not constrained? I get a notice that the block is not fully constrained and its a nightmare going through all the lines trying to find where I need to apply a constarinet.( I can't wait to get off ACAD and back to Inventor.)
2. When I try to save a dynamic block using the Save Block icon under Open/Save, if the dynamic block is not fully constrained, and I click save, when I reopen the block to edit all of my constraints are gone, this has happened twice. Now I just exit by Xing out and saving changes.